Owon PC321-TY Bedienungsanleitung
PC321-TY
Single/3-phase Power Clamp
Quick Start Guide
2
Safety Handling
WARNING: Failure to follow these safety notices could result in re,
electric shock, other injuries, or damage to the Power Clamp and
other property. Read all the safety notices below before using the
Power Clamp.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit on your own.
• Do not expose the unit or its accessories to ammable liquids, gases
or other explosives.
3
Technical Specications
Wireless Connectivity
Wi-Fi • 802.11 B/G/N20/N40
RF Characteristics • Operating frequency: 2.4GHz
• Internal Antenna
Physical Specications
Operating Voltage • 100~240 Vac 50/60 Hz
Calibrated Metering Accuracy • ≤ 100W ( Within ±2W )
• >100W ( Within ±2% )
CT Provided • CT 80A (default)
• CT 120A/200A/300A(optional)
Operating environment • Temperature: -20 ℃ ~ +55 ℃
• Humidity: ≤ 90% non-condensing
Dimension • 86(L) x 86(W) x 37(H) mm
4
Welcome
1
PC321-TY Power Clamp helps you monitor the amount of electricity
usage in your facility by connecting the clamp on to the power cable.
It can also measure Voltage, Current, PowerFactor, ActivePower.
This guide will provide you with an overview of the product and help
you get through the initial setup to installation.
• Tuya compliant
• Support Tap-to-Run and automation with other Tuya device
• Single/3 - phase electricity compatible
• Three current transformers for Single phase application
• Measures real-time Voltage, Current, PowerFactor, ActivePower and
total energy consumption
• Display the current temperature of the device on the App
• Suitable for both residential and commercial application
• Lightweight and easy to install
Features:
5
2
CT: Current Transformer Cable
Get to know your device
LED indicator
AC Input cable
CT3
Clamp
CT2
CT1
6
Reset Button
• Reset. Press and hold the reset button for 5 seconds until the LED
indicator ashes 3 times quikly to restore the power clamp to default
factory settings (energy data will be cleared). And it will get into EZ
mode for 3 minutes.
Reset Button
LED indicator
The LED status gives the following information of the power clamp:
LED Status What it means
Green LED Rapidly blink: EZ pair mode
Slowly blink: AP pair mode
Green LED solid on Device has connected with router.
No light Device can not connect with router.
• EZ pair mode (Default): Quick pair devices. You can set all devices to
this mode, and then add devices in batches on your phone.
• AP pair mode: If you would like to pair one specic device during
many devices. Please refer to FAQ1 to configure network in this
mode.
7
3Installaion
Important safety information!
• The power clamp must be installed and serviced only by a qualied
electrical personnel.
• Do not touch the terminals of the device during testing.
• Turn o all the power supply for this equipment before installing.
• Make sure that the power supply is off before connecting or
disconnecting it to an auxiliary device.
• Always use a properly rated voltage sensing device to conrm power
is o.
• Replace all devices, doors and covers before applying power to the
equipment.
Failure to follow these instructions will result in death or serious
injury.
Get started:
Please make sure the main power in your facility is off before
installing. Follow the schematics below as an example to wire the
Power Clamp for dierent phase.
N
Red/L1
Green/L2
Brown/L3
White/N
PC321
Load1
L1 N
Load2
L2 N
Load3
L3 N
L1/AL2/B
L3/C
L3/C
L2/B
L1/A
Circuit
Breaker
3 Phase electricity wiring diagram
8
3. Open the clamp as shown below. Apply it on the electric meter
cable. The arrow on the clamp should face to the correct direction of
the electricity current ows (P1 → P2). If the arrow faces the reverse
direction, the reading meter will display 0.
Follow the steps below:
1. Connect AC Input cable to a socket near the Electrical Box to power
on the Power Clamp according to the corresponding phase wiring
diagram.
2. Attach both ends of the Current Transformer Cables first like the
picture shown below. Then spinning the waterproof latch clockwise
until both ends have been tightened and secured.
Single Phase electricity wiring diagram
L
N
Red/L1
Green/L2
Brown/L3
White/N
PC321
Load1
L1 N
Load2
L2 N
Load3
L3 N
L1/AL2/B
L3/C
Circuit Breaker
9
P2
P1
Tips about the clamp:
• Cable diameter does not aect usage as long as the cable can pass
through the clamp hole.
• The meter has three clamps which can be applied to cable devices
for separate measurement. If applied to the same cable, all clamps
will produce the same reading.
4Congure Network
4.1 To get started, you will need:
• Connect your phone to the 2.4Ghz Wi-Fi network.
• A mobile phone with a 'SmartLife' APP installed.
Then follow the steps below:
• 1. Power on the power clamp.
• 2. Make sure the LED indicator is ashing green. If not, please reset it.
10
1. Open your App.
2. Login with an existing account. If you are a new user, you need to
create an account at rst.
3. Please click the '+' button at the top right corner of the App to add
devices.
4. Select 'Switch Module' to add manually the Power Clamp in
'Energy' list.
4.2 Add devices
5. Enter your home Wi-Fi account and password (Only support 2.4Ghz
Wi-Fi), then tap "Next" button.
Inhaltsverzeichnis
Andere Owon Messgerät Handbücher
Owon
Owon XSA800 Series Bedienungsanleitung
Owon
Owon HSA1000 Series Bedienungsanleitung
Owon
Owon PC321 Bedienungsanleitung
Owon
Owon HSA Series Bedienungsanleitung
Owon
Owon XDM Series Bedienungsanleitung
Owon
Owon CM240 Bedienungsanleitung
Owon
Owon CM2100 Bedienungsanleitung
Owon
Owon XSA1000 Series Bedienungsanleitung
Owon
Owon Lilliput HDS2062M Bedienungsanleitung
Owon
Owon HSA1000 Series Bedienungsanleitung
