P Tec IN5130 Bedienungsanleitung

Static Eliminators

Instruction Manual

Overhead Ionizing Blower

Model IN5130

Contents

1Description

Model IN5130 1

About Ptec™ Technology 1

Features 1

Power Requirements 2

2Operation and Use

Environmental Conditions 2

Set-up and Placement 2

Mounting 3

Power Connection 3

3Maintenance

Periodic Maintenance 4

Cleaning Exterior 4

Cleaning Emitter Points 4

Emitter Point Replacement 5

Service 6

Troubleshooting 6

4Specifications 7

5Service and Warranty 8

6 IN5130 Line Drawing 9

Description

Overhead Blower Model IN5130

The Model IN5130 68KHz AC overhead air ionizer is

designed to cover a complete workstation and to protect

sensitive electronic components from damage due to elec-

trostatic discharge (ESD). Using AC corona technology to

make the air more conductive, Ptec™ ionizers produce a

balanced stream of positive and negative air ions that

never need calibration. These devices are used in many

industries and manufacturing applications where static

electricity is a problem.

About Ptec™ Technology

A specialized piezoelectric high voltage transformer

makes Ptec™ ionizers among the most reliable products

available. Ptec™ ionizers are designed to remain in bal-

ance and to alarm when the HV output affects perform-

ance. The model IN5130 overhead static eliminator pro-

duces a 68KHz AC output of approximately 2200V and a

continuous stream of balanced air ions. Ionizers that use

Ptec™ technology do not require calibration and only mini-

mal maintenance.

Features

On the front panel of the IN5130 are six LEDs. Three

green LEDs indicate that power is applied to each of the

three Ptec™ HV transformers. The red LEDs illuminate

when an alarm condition occurs. A variable fan speed

control and on-off switch are also on the front panel. The

side panel of the ionizer has the IEC power input connec-

tor.

Features cont’d.

 Complete workstation protection.

 Rapidly decays static charges. (1KV to 100V, < 6 sec.

@ 24”).

 Excellent ion balance, 0 +10V.

 Stable AC technology.

 Ionization indicator light.

 HV alarm (red) lights.

 No periodic adjustments.

 Durable, replaceable tungsten alloy emitter points.

 Removable front grill.

 Adjustable air volume.

Power Requirements

The Model IN5130 High Frequency AC overhead air

ionizer is powered by an internal DC switching power sup-

ply that operates from 100-240 VAC 50/60 Hz. The output

of the supply is +24 VDC @ 1.5 AMP.

Operation and Use

Environmental Conditions

The IN5130 can be operated in areas where humidity

is 20-70% RH (Non-condensing). Excess humidity may af-

fect ionizer performance. The temperature range for the

IN5130 is 65-78°F (18-25°C).

Set-up and Placement

Use the IN5130 overhead blower in proximity to a

static sensitive area or object. The unit can be mounted

on the workstation or attached to a structure using the

mounting holes provided.

Mounting

Install the overhead ionizer 24” (60.9 cm) above

the work area to achieve the most uniform decay per-

formance.

The IN5130 mounts easily using the S-hooks sup-

plied. Chain or cable is not supplied and may be re-

quired. S-hooks attach to the unit. Chains can be easily

attached and mounted to the ceiling or other structure.

Power Connection

 Connect the IEC Cable to the main unit, and plug it in

an AC socket. (Caution: Use the appropriate IEC

cable for the country of use).

 Make certain the unit is grounded (Via IEC cable).

 Turn the unit on to start the corona process. The ion-

izer creates a continuous stream of positive and

negative air ions. The ionized airflow is directed

through the front grill. Charged objects in the ioniza-

tion area are rapidly neutralized .

 The ion airflow is adjustable using the fan speed con-

trol knob.

Caution

Do not use this ionizer in an explosive environ-

ment! Corona ionizers produce a weak plasma

that can cause ignition in explosive environ-

ments.

 The red alarm indicator light illuminates in the event

of a problem with the high voltage power output.

 Turn the power switch off after operation.

Maintenance

Periodic Maintenance

The only regular maintenance required for the

IN5130 is the periodic cleaning of the emitter points and

ionizer grills. Emitter point cleaning affects the static de-

cay ability of the ionizer and is important for maintaining

its optimal performance.

Cleaning the front grill and external chassis

Disassemble the front grill by squeezing the grill side

clips. Temporarily remove the grill. Clean it with a polyes-

ter wiper and a cleaning solution of 50% IPA (electronic-

grade isopropyl alcohol) and 50% de-ionized water. As-

semble it when it is dry. Use the same method to clean

the exterior of the unit, including the inlet grill.

Cleaning the emitter points

Contaminants will gradually accumulate on the tip

of the emitter points with continuous use. Periodic clean-

ing of the emitter points is necessary to maintain the per-

formance of the ionizer. If the emitter points are dirty,

clean them with a polyester or cotton swab and IPA. Do

not damage or loosen the emitter points.

Caution

The only serviceable parts inside the ionizer are

the replaceable emitter points. Any unauthor-

ized service will void the warranty and may

result in additional repair fees.

Follow these instructions to clean the emitter points:

1. Remove the front grill.

Moisten a swab or wiping cloth in the IPA solution.

3. Swab or wipe the emitter points until they are free of

particles.

4. Make certain the emitter points are straight and parallel

to the plane of the fan.

5. Replace the front grill.

6. Make sure the emitter points are dry before powering the

ionizer again.

Emitter Point Replacement

The IN5130 uses tungsten alloy precision etched emit-

ter needles. Contact Transforming Technologies for infor-

mation about ordering replacement emitters. The part num-

ber for emitters is listed below:

Replacement part Part Number

Tungsten replacement emitters 22-6423

Because the IN5130 high voltage output is AC, emitter

erosion from the ionization process on the electrodes is

minimal. Unless physically broken or stressed, the IN5130

emitters should last the life of the ionizer.

Follow these instructions to remove the emitter points:

1. Turn off and disconnect the unit from the AC power.

2. Remove the front grill.

3. Unscrew the threaded emitter point using a needle nose

pliers.

4. Replace and tighten the new emitter using the same

tool. Do not over-tighten.

5. Repeat steps 3 and 4 as required.

6. Make certain the emitter points are straight and paral-

lel to the plane of the fan.

7. Replace the front grill.

Service

Ptec™ ionizers are reliable products with a long ser-

vice life. If you feel your unit is not operating properly,

turn off the unit and disconnect the power cord. Contact

Transforming Technologies’ Technical Support for repair

assistance.

Troubleshooting

The information below provides a reference for prob-

lems that may arise with your IN5130 overhead blower. If

you have other problems not covered below, please con-

tact Transforming Technologies’ Technical Support for

repair assistance

Problem Causes

 Balance outside Emitter points are dirty, damaged

specifications. or not straight. Clean or replace

 Alarm light activated Low HV output, call for repair

Unit is arcing, call for repair

Short circuit, call for repair

Specifications

Power input 100-240VAC, 50/60 Hz, 36W

Power outlet Un-fused, 0.5A or 1.0A max.

Ion Emission AC, 68KHz

Balance +/- 10 volts, typical offset

Decay Time 1000V - 100V < 6 seconds at 24"

Temperature 66-78°F (19-25°C)

Humidity 20-60% RH (non-condensing)

Airflow 115 x 3 CFM, typical, high speed

Noise level 60dB(A) (Distance 1 meter)

Indicators Power: green LED Alarm: red LED

Controls On/Off rocker switch, fan speed knob

Emitter points .036" dia. Tungsten alloy, etched

Ozone <0.007 PPM

Mounting 4 "S" hooks provided

Dimensions 2.5"H x 39.4"W x 5.75”D, (64 x 1000 x 146

cm)

Weight 11.5lbs, (5.0kg)

Certifications

Service and Warranty

Transforming Technologies, LLC provides a lim-

ited warranty for the Model IN5130 overhead

blower. All new products are guaranteed to be free

from defects in material and workmanship for a pe-

riod of one (1) year from the date of shipment. Li-

ability is limited to servicing (after evaluating, repair-

ing or replacing) any product returned to Transform-

ing Technologies. The company does not warrant

damage due to misuse, neglect, alteration or acci-

dent. In no event shall Transforming Technologies

be liable for collateral or consequential damages.

To receive service under warranty, please con-

tact Transforming Technologies Technical Support.

About Transforming Technologies

Since 1998, Transforming Technologies has

helped electronic manufacturing facilities to protect

their products and processes from the many serious

problems associated with static electricity.

Transforming Technologies offers a wide range

of unique and outstanding products to detect, pro-

tect, eliminate and monitor electrostatic charges.

Our products are integral components of an effec-

tive static control program.

Inhaltsverzeichnis

Andere P Tec Luftionisator Handbücher

P Tec

P Tec IN5110 Bedienungsanleitung

Beliebte Luftionisator Handbücher anderer Marken

Static Clean

Static Clean 4203UC Bedienungsanleitung

SCS

SCS 960 Bedienungsanleitung

Desco EMIT

Desco EMIT C/E Series Bedienungsanleitung

Best Living Systems

Best Living Systems KHAOS Bedienungsanleitung

SCS

SCS 963E Bedienungsanleitung

Desco EMIT

Desco EMIT Chargebuster 50680 Montage- und Bedienungsanleitung

ELTEX

ELTEX ES60 Series Bedienungsanleitung

SMC Networks

SMC Networks IZN10E Series Bedienungsanleitung

Alkamedi

Alkamedi AMS 4100 Bedienungsanleitung

Desco EMIT

Desco EMIT 50664 Leitfaden

Aerisa

Aerisa 8100 Gebrauchsanweisung

greenfan

greenfan 1600-01 Bedienungsanleitung

Terra Universal

Terra Universal IonBar Installationsanleitung

Phonocar

Phonocar 04971 Bedienungsanleitung

Klarstein

Klarstein ST. OBERHOLZ OFFICE Bedienungsanleitung

Life Ionizers

Life Ionizers Fuzion Bedienungsanleitung

ITW

ITW Simco-Ion IQ Power Fantom Bedienungsanleitung

LIFE Ionizer

LIFE Ionizer M7 X NG Bedienungsanleitung