Pablo CLAMP Programmierhandbuch

ASSEMBLY & INSTALLATION INSTRUCTIONS

pg. 1

CLAMP

INSTALLATION

LOCKING

CLAMP

pg. 2

ALIGN THE FRONT SURFACE OF THE

CLAMP TO THE EDGE OF THE TABLE

SLIDE CLAMP FORWARD UNTIL THE

EDGE OF TABLE MEETS POST

USE INCLUDED HEX TOOL TO

TIGHTEN SET SCREW AND LOCK

TOP CLAMP IN POSITION

NOTE: CLAMP CAN ONLY BE APPLIED

TO SURFACES UP TO 3” THICK

3MM HEX KEY

ASSEMBLY

CLAMP

pg. 3

LIFT ARM TO ADJUST HEIGHT AND

ROTATE LIGHT SOURCE TO DESIRED POSITION

ADJUSTMENT

SLIDE ARM ONTO STEM

CONNECTOR LOCK

ABC D

PLUG TYPES:

POWER

SUPPLY

LOCK

1. SLIDE PLUG INTO POWER SUPPLY

2. ALIGN CONNECTOR/POWER

SUPPLY LOCKING FEATURES

3. INSERT CONNECTOR

4. TURN CONNECTOR 90 DEGREES

TO LOCK

A. N AMERICA B. UK C. EU D. AU

NOTE: CONTACT MANUFACTURER FOR

ADDITIONAL PLUG TYPE REQUIREMENTS.

ASSEMBLY & INSTALLATION INSTRUCTIONS

pg. 1

CLAMP FS

ASSEMBLY

CLAMP FS

pg. 2

REMOVE BASE FROM PACKAGING AND PLACE VERTICALLY IN

BOX SLOT AS SHOWN TO ASSIST WITH ASSEMBLY PROCEDURE

REMOVE EXISTING TOP

CLAMP FROM STEM

SLIDE BOTTOM OF CLAMP LAMP

INTO BASE CAVITY AS SHOWN

BOX SLOT

ASSEMBLY

CLAMP FS

pg. 3

2X SCREWS

AND WASHERS

SECURE CLAMP LAMP INTO BASE WITH

SUPPLIED WASHERS AND SCREWS

5SLIDE ARM ONTO STEM

CONNECTOR LOCK

ABCD

PLUG TYPES:

POWER

SUPPLY

LOCK

1. SLIDE PLUG INTO POWER SUPPLY

2. ALIGN CONNECTOR/POWER

SUPPLY LOCKING FEATURES

3. INSERT CONNECTOR

4. TURN CONNECTOR 90 DEGREES

TO LOCK

A. N AMERICA B. UK C. EU D. AU

NOTE: CONTACT MANUFACTURER FOR

ADDITIONAL PLUG TYPE REQUIREMENTS.

pg. 4

INFO@PABLODESIGNS.COM

888 MARIN STREET

SAN FRANCISCO, CA

94124

PABLODESIGNS.COM

CLAMP FS

ADJUSTMENT

LIFT ARM TO ADJUST HEIGHT AND

ROTATE LIGHT SOURCE TO DESIRED POSITION

pg. 1

CLAMP

MINI

ASSEMBLY & INSTALLATION INSTRUCTIONS

ASSEMBLY

CLAMP MINI

pg. 2

INSERT POST INTO BASE AS SHOWN

MAKE SURE THAT ARROW ON ORIENTATION

STICKER IS POINTING TO FRONT OF BASE.

REMOVE STICKER.

INSERT PROVIDED SCREW INTO HOLE IN BACK OF BASE.

USING HEX KEY SUPPLIED, TIGHTEN UNTIL POST IS SECURE.

HEX KEY AND SCREW

ORIENTATION

STICKER

ASSEMBLY

CLAMP MINI

pg. 3

SLIDE ARM ONTO POST

CONNECTOR LOCK

ABCD

PLUG TYPES:

POWER

SUPPLY

LOCK

1. SLIDE PLUG INTO POWER SUPPLY

2. ALIGN CONNECTOR/POWER

SUPPLY LOCKING FEATURES

3. INSERT CONNECTOR

4. TURN CONNECTOR 90 DEGREES

TO LOCK

A. N AMERICA B. UK C. EU D. AU

NOTE: CONTACT MANUFACTURER FOR

ADDITIONAL PLUG TYPE REQUIREMENTS.

ADJUSTMENT

LIFT ARM TO ADJUST HEIGHT AND

ROTATE LIGHT SOURCE TO DESIRED POSITION

HI-LOW SWITCH

Andere Handbücher für CLAMP

Andere Pablo Außenleuchte Handbücher

Pablo

Pablo LIM360 Programmierhandbuch

Pablo

Pablo circa Programmierhandbuch

Pablo

Pablo LUCI TABLE Bedienungsanleitung

Pablo

Pablo Uma Mini Bedienungsanleitung

Pablo

Pablo Corner Office Programmierhandbuch

Pablo

Pablo CLAMP Programmierhandbuch

Beliebte Außenleuchte Handbücher anderer Marken

Sealey

Sealey LED37 Bedienungsanleitung

nordlux

nordlux VEJERS Benutzerhandbuch

SImx

SImx ELITE LED LHTC637 Bedienungsanleitung

GEV

GEV CAROLINE 10833 Bedienungsanleitung

NEBO

NEBO NEB-LSP-0020 Bedienungsanleitung

WE-EF

WE-EF PFL540 LED Bedienungsanleitung

Lindby

Lindby 9949029 Bedienungsanleitung

HEPER

HEPER DOGO Side LW6048.585-US Montage- und Bedienungsanleitung

HEPER

HEPER LW8034.003-US Montage- und Bedienungsanleitung

Maretti

Maretti VIBE S 14.6080.04.A Bedienungsanleitung

BEGA

BEGA 84 253 Handbuch

HEPER

HEPER MINIMO Montage- und Bedienungsanleitung

LIGMAN

LIGMAN BAMBOO 3 Bedienungsanleitung

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung

urban ambiance

urban ambiance UQL1273 Bedienungsanleitung

TotalPond

TotalPond 52238 Bedienungsanleitung

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Bedienungsanleitung