Pacific hydrostar 37952 Bedienungsanleitung

SUBMERSIBLE PUMP

Model 37952

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at: http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions, please call 1-800-444-3353.

REV 04e, 08i

PRODUCT SPECIFICATIONS

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly, op-

erating, inspection, maintenance and cleaning procedures, parts list and assem-

bly diagram. Keep your invoice with this manual. Write the invoice number on the

inside of the front cover. Keep this manual and invoice in a safe and dry place for

future reference.

GENERAL SAFETY WARNINGS AND PRECAUTIONS

1. KEEP WORK AREA CLEAN AND DRY. Cluttered, damp, or wet work areas

invite injuries.

2. KEEP CHILDREN AWAY FROM WORK AREA. Do not allow children to handle

this product.

3. STORE IDLE EQUIPMENT. When not in use, tools and equipment should be

stored in a dry location to inhibit rust. Always lock up tools and equipment, and

keep out of reach of children.

4. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR

DRUGS. Read warning labels on prescriptions to determine if your judgement or

SKU 37952 PAGE 2

reﬂexes are impaired while taking drugs. If there is any doubt, do not attempt to

use this product.

5. USE EYE, BREATHING, HEARING PROTECTION. Wear ANSI approved safety

impact eye goggles and an ANSI approved full face shield when using this prod-

uct. ANSI approved safety impact eye goggles, full face shield, are available from

Harbor Freight Tools.

6. DRESS SAFELY. Do not wear loose clothing or jewelry, as they can become

caught in moving parts. Wear a protective hair covering to prevent long hair from

becoming caught in moving parts. If wearing a long-sleeve shirt, roll sleeves up

above elbows.

7. DO NOT OVERREACH. Keep proper footing and balance at all times to prevent

tripping, falling, back injury, etcetera.

8. INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS.

9. STAY ALERT. Watch what you are doing at all times. Use common sense. Do

not use this product when you are tired or distracted from the job at hand.

10. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that

it will operate properly and perform its intended function. Check for damaged

parts and any other conditions that may affect the operation of this product. Re-

place or repair damaged or worn parts immediately.

11. REPLACEMENT PARTS AND ACCESSORIES: When servicing, use only identi-

cal replacement parts. Only use accessories intended for use with this product.

Approved accessories are available from Harbor Freight Tools.

12. MAINTAIN THIS PRODUCT WITH CARE. Keep this product clean, dry, and keep

all cutting bits and chisels sharp for better and safer performance.

13. MAINTENANCE: For your safety, service and maintenance should be performed

regularly by a qualiﬁed technician.

14. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or

attachment to do the work of a larger industrial tool. There are certain applica-

tions for which this tool was designed. It will do the job better and more safely

at the rate for which it was intended. Do not modify this tool, and do not use this

tool for a purpose for which it was not intended.

15. WARNING! The warnings, precautions, and instructions discussed in this

manual cannot cover all possible conditions and situations that may occur. The

operator must understand that common sense and caution are factors, which

cannot be built into this product, but must be supplied by the operator.

SKU 37952 PAGE 3

SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS

1. MAINTAIN A SAFE WORKING ENVIRONMENT. Keep the work area well lit.

Make sure there is adequate surrounding workspace. Always keep the work area

free of obstructions, grease, oil, trash, and other debris. Do not use this product

in areas near ﬂammable chemicals, dusts, and vapors. Do not use this product in

a damp or wet location.

2. GROUND THIS PRODUCT. This product is equipped with a 3-Prong Electrical

Plug. To comply with the National Electric Code, and to provide additional pro-

tection from the risk of electrical shock, this product should only be connected to

a 115 Volt, 3-hole, electrical outlet that is protected by a Ground Fault Circuit

Interrupter (GFCI).

3. NEVER USE AN EXTENSION CORD TO POWER THIS PRODUCT.

SKU 37952 PAGE 4

4. WARNING! Do not pump ﬂammable, explosive, or corrosive liquids such

as gasoline, fuel oil, kerosene, etc. Do not use this product in the presence of

ﬂammable gases or liquids.

5. USE EYE PROTECTION. Always wear ANSI approved safety impact eye

goggles when assembling and using this product.

6. NEVER PLUG THIS PRODUCT INTO AN ELECTRICAL POWER SUPPLY

WHILE STANDING ON A WET OR DAMP SURFACE.

7. NEVER LIFT THIS PRODUCT BY ITS ELECTRICAL POWER CORD.

8. AVOID UNINTENTIONAL STARTING. Make sure you are prepared to begin

work before turning on this product.

9. SECURE THE DISCHARGE HOSE (not included) BEFORE STARTING THE

PUMP. An unsecured discharge hose may whip, causing personal injury and/or

property damage.

10. NEVER RUN THE PUMP DRY. It will increase wear to the unit and possibly

cause Seal damage.

11. ALWAYS CHECK THE DISCHARGE HOSE (not included) FOR WEAK OR

WORN CONDITIONS BEFORE EACH USE. Check to make sure all connec-

tions are tight and secure.

12. ALWAYS UNPLUG THIS PRODUCT FROM ITS ELECTRICAL SUPPLY

SOURCE BEFORE PERFORMING ANY INSPECTION, MAINTENANCE, OR

CLEANING PROCEDURES.

14. WARNING: People with pacemakers should consult their physician(s) before

using this product. Operation of electrical equipment in close proximity to a heart

pacemaker could cause interference or failure of the pacemaker.

SKU 37952 PAGE 5

13. MAINTAIN LABELS AND NAMEPLATES ON THIS PRODUCT. These carry

important information. If unreadable or missing, contact Harbor Freight Tools for

a replacement.

UNPACKING

When unpacking, check to make sure all the parts shown on the Parts List on page 7are

included. If any parts are missing or broken, please call Harbor Freight Tools at the

number shown on the cover of this manual as soon as possible.

ASSEMBLY INSTRUCTIONS

NOTE: For additional information regarding the parts listed on the following pages, refer

to the Assembly Diagram on page 8.

1. WARNING! Always make sure the Submersible Pump is unplugged

from its electrical outlet prior to performing any assembly or making any

adjustments to the unit.

2. Along with the Submersible Pump are three accessory Hose Adapters

(parts #1A, #1B, #1C) and one Rubber Washer (part #2). The sizes of the Hose

Adapters are 5/8” O.D., 3/4” O.D., and 1” O.D. (See Figure A.)

DISCHARGE HOSE

(NOT INCLUDED)

1” HOSE ADAPTER (#1C) 5/8” HOSE ADAPTER (#1A)

3/4” HOSE ADAPTER (#1B)

RUBBER WASHER (#2)

SCREW SLEEVE

(#3)

RUBBER WASHER

(#2)

HOSE ADAPTER

(#1A, #1B, #1C)

SCREW SLEEVE (#3)

HOSE ADAPTER (#1A, #1B, #1C)

POWER CORD/PLUG

(#43)

Figure A

4. Unscrew and remove the Screw Sleeve (part #3) from the Pump. Place the

Rubber Washer (part #2) on the previously selected Hose Adapter

(part #1A, #1B, or #1C). (See Figure A.)

5. Screw the Screw Sleeve (part #3), with its Hose Adapter (part #1A, #1B, or #1C)

and Rubber Washer (part #2), ﬁrmly back onto the Pump. (See Figure A.)

6. Insert one end of the Discharge Hose ﬁrmly onto the Hose Adapter (part #1A,

#1B, or #1C). Then, route the other end of the Discharge Hose to the desired

drainage area. (See Figure A.)

7. Lower the Pump in the water on a solid, level surface. Do not lower the Pump by

means of the Power Cord/Plug (part #43) or Discharge Hose. Do not place the

Pump directly on clay earth or sand sufaces. A minimum of two inches of water

is recommended to properly prime the Pump.

8. IMPORTANT! Do not run the Pump unless it is submerged in water. Doing

so will damage the Pump.

9. Route the Power Cord/Plug (part #43) to its electrical outlet safely to avoid trip-

ping over the Power Cord or damage to the Power Cord/Plug. Do not allow the

Power Cord/Plug to become wet. Always place the Power Cord/Plug in a dry

location and as far away as possible from the draining and drainage areas.

10. Plug the Power Cord/Plug (part #43) into its electrical outlet. The Pump will then

begin to operate.

11. NOTE: If during operation the water stops ﬂowing from the Discharge Hose,

unplug the Pump immediately to avoid damage to the Pump. This indicates the

water level is probably too low, causing the Pump to lose its suction seal.

12. Once the pumping process is completed, unplug the Power Cord/Plug (part #43)

from its electrical outlet. Remove the Pump from the draining area, and store the

Pump in a clean, dry location.

SKU 37952 PAGE 6

3. Select the Hose Adapter (parts #1A, #1B, or #1C) that coincides with the inside

diameter of the Discharge Hose (not included) you will use. (See Figure A.)

INSPECTION, MAINTENANCE, AND CLEANING

1. CAUTION: Always unplug the Pump from its 115 volt electrical outlet before

performing any inspection, maintenance, or cleaning.

2. BEFORE EACH USE, inspect the general condition of the Pump. Check for

loose connections, misalignment or binding of moving parts, cracked or broken

SKU 37952 PAGE 7

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DIS-

TRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE

OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED

TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTUER AND/OR DISTRIBUTOR

EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN

BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES

ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR

REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-

MENT PARTS THERETO.

NOTE: Some parts are listed and shown for illustration purposes only, and are not avail-

able individually as replacement parts.

PARTS LIST

3. BEFORE EACH USE, check to make sure the lower Filter (part #20) area of the

unit is clean and free of dirt and debris. If neccessary, use a wet-and-dry vacuum

or compressed air to clean the Filter area.

4. WHEN NOT IN USE, THIS PRODUCT SHOULD BE STORED IN A DRY LOCA-

TION TO INHIBIT RUST.

parts, damaged electrical wiring, and any other condition that may affect its safe

operation. If abnormal noise or vibration occurs, have the problem corrected be-

fore further use. Do not use damaged equipment.

SKU 37952 PAGE 8

ASSEMBLY DIAGRAM

NOTE: Some parts are listed and shown for illustration purposes only, and are not avail-

able individually as replacement parts.

A,1B,1C

LIMITED 1 YEAR / 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high

quality and durability standards, and warrants to the original purchaser that for a period

of ninety days from date of purchase that the engine/motor, the belts (if so equipped),

and the blades (if so equipped) are free of defects in materials and workmanship. Harbor

Freight Tools also warrants to the original purchaser, for a period of one year from date of

purchase, that all other parts and components of the product are free from defects in ma-

terials and workmanship (90 days if used by a professional contractor or if used as rental

equipment). This warranty does not apply to damage due directly or indirectly, to misuse,

abuse, negligence or accidents, repairs or alterations outside our facilities, normal wear and

tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons

or property, or for incidental, contingent, special or consequential damages arising from

the use of our product. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation of exclusion may not apply to you. THIS

WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with

transportation charges prepaid. Proof of purchase date and an explanation of the com-

plaint must accompany the merchandise. If our inspection veriﬁes the defect, we will either

repair or replace the product at our election or we may elect to refund the purchase price

if we cannot readily and quickly provide you with a replacement. We will return repaired

products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning

the product.

This warranty gives you speciﬁc legal rights and you may also have other rights

which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

SKU 37952 PAGE 9

Inhaltsverzeichnis

Andere Pacific hydrostar Wasserpumpe Handbücher

Pacific hydrostar

Pacific hydrostar Pacific Hydrostar 2" or 3" Dirty Water Pump... Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 69297 Montageanleitung

Pacific hydrostar

Pacific hydrostar Pacific Hydrostar Portable Utility Pump... Installationshandbuch

Pacific hydrostar

Pacific hydrostar 68486 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 47906 Installationshandbuch

Pacific hydrostar

Pacific hydrostar 69303 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 68390 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 47907 Installationshandbuch

Pacific hydrostar

Pacific hydrostar 69302 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 94649 Assembly and Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar Pacific Hydrostar 212cc Gasoline Powered Clear Water... Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 95977 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar Pacific Hydrostar 1-1/2" Gasoline Powered Clear Water... Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 98342 Installationshandbuch

Pacific hydrostar

Pacific hydrostar 90107 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 69746 Montageanleitung

Pacific hydrostar

Pacific hydrostar 94639 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 66585 Stücklistenhandbuch

Pacific hydrostar

Pacific hydrostar Pacific Hydrostar Portable Sprinkler Pump Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float... Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 66514 Handbuch

Pacific hydrostar

Pacific hydrostar 68476 Montageanleitung

Pacific hydrostar

Pacific hydrostar 69747 Montageanleitung

Pacific hydrostar

Pacific hydrostar PACIFIC HYDROSTAR 66351 Installationshandbuch

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung