Pacific hydrostar 68486 Bedienungsanleitung

1/4 HP Clear Water Pump With Float

68486 Clear Water Pump With Float

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

When unpacking, make sure that the product is intact and undamaged.

If any parts are missing or broken, please call 1-800-444-3353 as soon as possible.

Visit our website at: http://www.harborfreight.com

or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

Page 2 For technical questions, please call 1-800-444-3353. SKU 68486

Before start-up, note the following:

The pump can be connected to any shock-proof plug

which has been installed according to regulations.

The plug must have a supply voltage of 120 V~ at 60 Hz.

CAUTION

This pump is intended for use with clear water only.

WARNING

IMPORTANT! For your own safety –

before starting to run the pump, please have

the following items checked by an expert:

1. Risk of electric shock – This pump is supplied

with a grounding conductor and grounding-type

attachment plug. To reduce the risk of

electric shock, connect only to a properly

grounded, grounding-type receptacle.

2. Risk of electric shock – This pump has not been

investigated for use in swimming pool areas.

3. The electrical connections must be

protected from moisture. Do not

submerge power cord connection.

4. If there is danger of ooding, the electrical

connections must be taken to higher ground.

5. Circulation of caustic uids, as well as the circulation

of abrasive materials, must be avoided at all costs.

6. The pump must be protected from frost.

7. The pump must be protected from running dry.

8. Access by children should also be

prevented with appropriate measures.

9. WARNING: Handling the Power Cord

on this product will expose you to lead,

a chemical known to the State of California

to cause cancer, and birth defects or other

reproductive harm. Wash hands after handling.

(California Health & Safety Code § 25249.5, et seq.)

10. The warnings, precautions, and instructions

discussed in this instruction manual cannot

cover all possible conditions and situations

that may occur. It must be understood by the

operator that common sense and caution are

factors which cannot be built into this product,

but must be supplied by the operator.

Fluid Type

The Pump is designed for use with water with

a maximum temperature of 77° F (25°C).

Do not use the pump for other uids, especially not

fuels, cleaning uids, or other chemical products.

Specications

Electrical Requirements 120V~ / 60Hz / 2.3 A

Motor 1/4 Horsepower Electric

Power Cord Length

10 FT. (Do not submerge

beyond power cord length.

Do not submerge power

cord connection.)

Maximum Flow Rate 1200 GPH

Maximum Head Lift 20 FT.

Pressure 8.7 PSI

236418

PCP-801

Installation

The submersible pump must be installed with either:

a. A xed pipeline or

b. A exible hose pipe.

Please note!

1. Do not install the pump by suspending it

unsupported from its delivery pipe or power cord.

The pump must be suspended from the handle

or be placed on the bottom of the area.

2. Make sure the Pump rests on at, level

and solid foundation. Do not operate it on

earth, clay, sand or gravel surfaces.

3. Make sure the Pump’s inlet openings near

the suction base are free of debris.

4. Avoid installing Pump in areas

of extreme heat or cold.

5. If the piping installed with Pump runs in excess of

ten feet, use a check valve (not

included) to prevent back ow.

Power Supply

1. The pump is equipped with a shock-proof plug

according to regulations. The pump is designed

to be connected to 120 V~, 60 Hz safety socket.

2. Make sure that the socket is sufciently

secured and is in excellent condition.

3. When the plug is inserted into the socket

the pump will be on standby.

WARNING! If the power cord or plug is damaged,

do not use the pump. The power cord or plug

may only be repaired by a certied electrician.

Page 3For technical questions, please call 1-800-444-3353.SKU 68486

Hose Connections

1. Use the included adaptor to connect a 1-1/2”

or larger hose to the pump outlet using a step

nipple and hose clamps (not included).

2. Route the hose to the desired discharge area. The

hose should be kept as short as possible with a

minimum number of turns. For best performance,

the max. recommended hose length is 50 ft.

3. To reduce vibration and noise, a short section

of rubber hose maybe be attached to the

end of the discharge line with clamps.

Areas of use

1. This pump can be used to transfer water

(e.g. household, farming, plumbing).

Operation

After reading these instructions,

consider the following points before starting the pump:

1. Verify that the pump rests on the oor of the shaft,

if it is not suspended by the handle.

2. Verify that the delivery pipe is properly connected.

3. Verify that the electrical connection is 120 V~, 60 Hz.

4. Verify that the electrical socket is in good condition.

5. Verify that water and moisture cannot get near the

power supply socket or power cord connection.

6. NOTE: Snap the cord for the Float Switch into

the cable clip on the side of the housing. Once

the cord is snapped into place, you can adjust

the level that the Pump turns on by adjusting

the length of the Float Switch’s cord.

7. The Float Switch will automatically turn off the Pump

when the level of water drops below the Switch.

8. Verify that the pump is installed so as to

prevent running dry. NOTE: The oat

must be allowed to move freely and must

shut off the Pump before it runs dry.

9. CAUTION: Do not run the Pump dry.

Doing so will increase wear on the unit and

can possibly lead to seal damage.

10. NOTE: The Pump has a built-in thermal protector

for the motor, which automatically shuts it off

to avoid overheating. After it cools, it will cycle

back on. Wait for the cycle to continue-do not try

to manually turn on Pump after it has cut off.

11. Plug power cord into an outlet tted with a GFCI.

12. Verify that the discharge water travels

several feet from the foundation.

13. NOTE: It is normal for air bubbles from trapped air

to appear around the handle or pressure switch.

The pump is equipped with a de-aerating device

with removes air locked in the Pump. Also, if the

water level drops below the vent valve, some

water might purge from Pump via the vent valve.

Page 4 For technical questions, please call 1-800-444-3353. SKU 68486

Maintenance

TO PREVENT SERIOUS INJURY FROM

ACCIDENTAL OPERATION:

Unplug the Pump from its electrical

outlet before performing any inspection,

maintenance, or cleaning procedures.

If the pump is moved during operation,

ush it out with clean water after every use.

Quarterly Maintenance

The below maintenance must be performed at least

once every 3 months under optimal conditions.

For frequent use, or dirty areas,

more frequent maintenance is required.

1. Clean sludge and debris from the base of the Pump.

2. Rinse the housing off with clean water.

3. Clean bers from inside the pump housing

with a clean cloth, then store Pump in a dry

and clean location away from children.

4. If the pump housing cannot be cleaned from

the outside, it must be thoroughly cleaned.

Unplug the power cord before maintenance.

Dismantle the bottom part of the pump as follows:

a. Clean the impeller with clean water.

b. To prevent damage, do not rest the pump on

the impeller or pry against the impeller.

c. Reassemble in reverse order.

Page 5For technical questions, please call 1-800-444-3353.SKU 68486

Troubleshooting

Problem Possible Causes Possible Solutions

Pump runs, but

will not deliver

any water.

1. Filter and/or impeller clogged.

2. When starting, the water

height falls below the minimum

water level (1-1/2″).

3. Low line voltage.

4. Optional check valve stuck

or installed backwards.

1. Remove lter. Clean out dirt and debris from

lter and impeller. Then replace Filter.

2. There must be at least 1-1/2″ deep water

for the Pump to operate properly.

3. Consult with an electrician.

4. Remove and examine check valve.

Pump won’t

start or run.

1. Check power connections

and circuits/fuses.

2. Water level too low.

3. Filter and/or impeller clogged.

4. Defective motor.

1. Consult with an electrician.

2. Allow water level to rise enough to operate the

Float Switch or move Pump to a lower location.

3. Remove lter. Clean out dirt and debris from

lter and impeller. Then replace lter.

4. Have a qualied service technician repair or replace.

Excessive noise

or vibration.

1. Worn bearings.

2. Debris in impeller.

3. Discharge hose restricted.

1. Have a qualied service technician repair or replace.

2. Remove lter. Clean impeller. Then replace lter.

3. Clean Pump and discharge hose.

Pump starts

and stops too

frequently.

1. Water temperature too high.

2. Back ow of water from

discharge hose.

1. Do not exceed 77° Fahrenheit water temperature.

2. Install or inspect optional check valve.

Follow all safety precautions whenever diagnosing or servicing the tool.

Disconnect power supply before service.

Page 6 For technical questions, please call 1-800-444-3353. SKU 68486

Part Description Qty.

1 Power Cord 1

2 Float Switch 1

3 Screw 1

4 O-Ring 1

5 Screw 4

6 Motor Cover 1

7 Capacitor 1

8 Capacitor Frame 1

9 Screw 1

10 Capacitor Holder 1

11 Stator 1

12 Rotor 1

13 Lock Ring 1

14 Bearing 2

Part Description Qty.

15 Motor Case 1

16 O-Ring 1

17 Seal 1

18 Impeller Washer 1

19 Seal 1

20 Impeller 1

21 Nut 1

22 Pump Housing 1

23 O-Ring 1

24 Nut 1

25 Elbow Connector 1

26 Base 1

27 Screw 1

28 Connector 1

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

PARTS LIST

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Page 7For technical questions, please call 1-800-444-3353.SKU 68486

ASSEMBLY DIAGRAM

39 float switch 1

Page 8 For technical questions, please call 1-800-444-3353. SKU 68486

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure

that its products meet high quality and durability

standards, and warrants to the original purchaser

that this product is free from defects in materials and

workmanship for the period of 90 days from the date

of purchase. This warranty does not apply to damage

due directly or indirectly, to misuse, abuse, negligence

or accidents, repairs or alterations outside our facilities,

criminal activity, improper installation, normal wear and

tear, or to lack of maintenance. We shall in no event

be liable for death, injuries to persons or property, or

for incidental, contingent, special or consequential

damages arising from the use of our product. Some

states do not allow the exclusion or limitation of incidental

or consequential damages, so the above limitation of

exclusion may not apply to you. THIS WARRANTY IS

EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part

must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation

of the complaint must accompany the merchandise. If

our inspection veries the defect, we will either repair

or replace the product at our election or we may elect

to refund the purchase price if we cannot readily and

quickly provide you with a replacement. We will return

repaired products at our expense, but if we determine

there is no defect, or that the defect resulted from

causes not within the scope of our warranty, then

you must bear the cost of returning the product.

This warranty gives you specic legal rights and you may

also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 Camarillo, CA 93011 • (800) 444-3353

Inhaltsverzeichnis

Andere Pacific hydrostar Wasserpumpe Handbücher

Pacific hydrostar

Pacific hydrostar 69747 Montageanleitung

Pacific hydrostar

Pacific hydrostar Pacific Hydrostar 212cc Gasoline Powered Clear Water... Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 69302 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 95977 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar SUBMERSIBLE DIRTY WATER PUMP 93819 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar Pacific Hydrostar Portable Utility Pump... Installationshandbuch

Pacific hydrostar

Pacific hydrostar PACIFIC HYDROSTAR 66351 Installationshandbuch

Pacific hydrostar

Pacific hydrostar Pacific Hydrostar 2" or 3" Dirty Water Pump... Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 68476 Montageanleitung

Pacific hydrostar

Pacific hydrostar 66585 Stücklistenhandbuch

Pacific hydrostar

Pacific hydrostar 37952 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar PACIFIC HYDROSTAR 95267 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 47906 Installationshandbuch

Pacific hydrostar

Pacific hydrostar 94639 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 69297 Montageanleitung

Pacific hydrostar

Pacific hydrostar 65351 Stücklistenhandbuch

Pacific hydrostar

Pacific hydrostar Pacific Hydrostar 1-1/2" Gasoline Powered Clear Water... Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 47907 Installationshandbuch

Pacific hydrostar

Pacific hydrostar PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float... Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 94649 Assembly and Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 69303 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 69297 Montageanleitung

Pacific hydrostar

Pacific hydrostar 68390 Bedienungsanleitung

Pacific hydrostar

Pacific hydrostar 69746 Montageanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung