Pacific B-1500 Bedienungsanleitung

PLEASE READ THIS BOOK

This operator’s book has important informaon for the use and safe operaon of this machine. Read this

book carefully before starng the machine. Keep this book and tell all operators to read the book. If you

do not follow the instrucons, you can cause an injury or damage equipment, furniture or buildings.

For new books, please download your copy from our website www.pacicoorcare.com or write to:

Pacic Floorcare

2259 S. Sheridan Drive

Muskegon, MI 49442-6252

Carefully inspect all components to ensure that there is no concealed freight damage. If such damage is

discovered, le a “CONCEALED DAMAGE REPORT” immediately with the delivering carrier.

The contents of this manual are based on the latest product informaon available at the me of

publicaon. Pacic reserves the right to make changes or improvements without noce.

Thank you for purchasing a Pacic Floorcare product. Warranty registraon will allow us to beer

serve you over the lifeme of the product. For quick and easy registraon, go to:

www.pacicoorcare.com/Register Product.

PARTS & OPERATING MANUAL

B-1500 BURNISHER

1500 RPM WITH ABS BASE

IMPORTANT SAFETY INSTRUCTIONS

To ensure the safe operaon of this machine, you must read and understand all warnings and instrucons in this book. If you

do not understand, ask your supervisor.

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE

WARNING: To reduce the risk of re, electric shock, or injury:

1. You must be trained to operate this machine. This machine is to be operated for its intended use only.

2. Do not operate this machine unless it is completely assembled.

3. Always use a three-wire electrical system connected to the electrical ground. For maximum protecon against electrical

shock, use a circuit that is protected by a ground fault circuit interrupter. Consult your electrical contractor.

4. To prevent electric shock, always remove the electrical plug from the electrical outlet before doing any repairs or mainte-

nance and when leaving the machine unaended.

5. To prevent electric shock, keep the machine surface dry. Do not subject to rain. Store the machine in a dry building area.

Clean the machine with a dry cloth only.

6. Machines can cause an explosion when near ammable materials and vapors. Do not use this machine with or near fuels,

grain dust, solvents, thinners, or other ammable materials. Do not use ammables to clean this machine.

7. A qualied or authorized person must do maintenance and repairs.

8. To prevent damage to the power cord, do not move this machine over the power cord. Always li the power cord over

the machine. Do not pull or carry cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or

corners. Keep cord away from heated surfaces.

9. Do not use with damaged cord or plug. If the machine is not working as it should, has been dropped, damaged, le out-

doors, or dropped into water, return it to a service center.

Grounding Instrucons

This machine must be grounded. If it should malfuncon or break down, grounding provides a path of least resistance for

electric current to reduce the risk of electric shock. This machine is equipped with a cord having an equipment-grounding

conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded

in accordance with all local codes and ordinances.

WARNING - Improper connecon of the equipment-grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do

not modify the plug provided with the machine - if it will not t the outlet, have a proper outlet installed by a qualied

electrician.

This machine is for use on a nominal 120-volt circuit, and has a ground-

ed plug that looks like the plug illustrated in gure A. A temporary

adapter that looks like the adapter illustrated in gures B and C may be

used to connect this plug to a 2-pole receptacle as shown in gure B

if a properly grounded outlet is not available. The temporary adapter

should be used only unl a properly grounded outlet (gure A) can be

installed by a qualied electrician. The green colored rigid ear, lug, or

the like extending from the adapter must be connected to a perma-

nent ground such as a properly grounded outlet box cover. Whenever

the adapter is used, it must be held in place by a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permied by

the Canadian Electrical Code

EXTENSION CORDS

Use only three-wire 12/3 or larger gauge approved extension cords

that have three-prong grounding type plugs and three-pole receptacles

that accept the appliance’s plug. Replace or repair any damaged cords

or plugs.

When servicing, refer to authorized person only. Use only idencal

replacement parts.

NOTE: Do not use adapters shown in

gures B & C in Canada

OPERATING PROCEDURES

WARNING! For the safe operaon of this machine follow the instrucons given in this booklet and the training given by

your supervisor. Failure to do so can result in personal injury and/or damage to machine and property!

DO NOT OPERATE MACHINE IN AN EXPLOSIVE ENVIRONMENT!

The models shown in this manual are intended for commercial use. THIS MACHINE IS NOT INTENDED FOR SPRAY BUFFING.

USING THIS UNIT FOR SPRAY BUFFING WILL VOID WARRANTY.

PREPARATION

To prepare the machine for operaon, make sure it is of correct voltage and properly assembled. If in doubt, ask your su-

pervisor.

Your new oor machine operates in a straight-line forward moon, rather than the normal side to side moon of a conven-

onal single disc machine. Be prepared by having your oor area cleared and ready for the fast acon of a burnisher.

Prepare the oor area by sweeping, dusng or mopping as needed. Check the proper applicaon recommendaons and

procedures found on the label of your nish container. IF IN DOUBT, CALL YOUR SUPERVISOR .

WARNING! NEVER USE THIS MACHINE WITH FLAMMABLE OR EXPLOSIVE MATERIAL!

For Burnishing: Select the correct clean oor pad (your supplier can help you). The lighter color oor pads (bu or white) are

normally used for the burnishing procedure.

NEVER OPERATE THE MACHINE WITHOUT THE FLOOR PAD INSTALLED!

It is very important to select clean, dry pads of uniform thickness. Pads with high or low secons, or hard or so spots are

unacceptable. Pads of open weave are recommended; because close weaves tend to load up fast, bog down the machines,

cause circuits to overload and generally give poor results.

Unplug the machine from the wall outlet and then p the machine back to expose the pad driver. Remove the pad center

lock ring. Carefully center the pad onto the pad driver and secure with the locking ring. Check for level, centering and at-

ness.

OPERATION

Set the machine upright onto the pad. Plug the machine’s power cable into a properly grounded outlet (see Safety Instruc-

ons). Next, release the handle by unlocking the knob and allow the handle to lower into a comfortable posion. THEN

ALWAYS SECURE THE HANDLE LOCKING KNOB. This will allow the operator to easily control the pad pressure.

Depress the handle slightly to elevate the pad from the oor. This is to avoid burning the oor on inial start up, before the

operator is ready to move forward. Pull out on the “Watch Dog” Safety Lock buon and start the machine by depressing

either the le or right switch levers.

When you’re ready to move forward, lower the machine head and pad to the oor and proceed forward in a straight line, at

a steady pace.

MAINTENANCE

AFTER EACH USE: Store the machine in a clean dry area. Wipe the enre machine and cord down with a clean cloth.

Remove the pad and clean thoroughly. Wrap the machine’s electrical cord onto the handles and the cord hook provided.

CHECK the cord and plug for nicks, cuts or damage. Report these to your supervisor for correcon.

WARNING! Always disconnect the machine’s electrical plug from the electrical outlet before performing any service, main-

tenance, pad changing or inspecon of the machine.

MOTOR: The motor is lubricated for life under normal use. No oiling or greasing is necessary. However, if the machine is

used in dusty areas the motor should be cleaned. Blowing the motor out with compressed air or with the exhaust from a

vacuum is suggested. Keeping the motor clean will allow the clear passage of air for venlaon and prevent overheang.

BELT TENSION: Proper belt tension is important for smooth operaon and belt life. Check the belt tension and have no

more than a 1/8-inch deecon. If adjustment is needed, loosen the four (4) motor mounng bolts. Then move the motor

and reghten the four (4) motor mounng bolts.

CARBON BRUSH INSPECTION: Long life 3000-hour carbon brushes are installed in the motor. The machine is also equipped

with a carbon brush wear indicator light to signal when a carbon brush change is required.

B-1500 BURNISHER, ABS BASE

485904 - Pad Assembly, Flex Drive

6 7

14 15

16 17

39 40

59 60

65 66

ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY.

1962002 Screw, 10-32 x 1/2 Oval 2 42 502396 Cover, Motor 1

2504810 Interlock Assembly 143 See Pg. 7 Motor, 1.5HP DC 1

3962011 Screw, 10-32 x 1 3/4 Oval 2 44 502481 Collar, Upper Shaft 1

4486407C Cover, Switch Box 145 920002 Nut, 3/8-16 Hex 4

5980018 Washer, #10 C-Sunk External 1 46 980009 Washer, 3/8 Lock 4

6509821 Washer, Rubber 2 47 980003 Washer, 3/8 Flat 9

7920005 Nut, 3/8-24 Hex Jam 1 48 501380 Bearing, Block 2

8505121 Lever, Switch Left 149 486602 Plate, Stiffener 1

9485002 Switch Kit 150 483214 Base, B-1500, ABS 1

10 505120 Lever, Switch Right 151 501286 Bumper, Base, 48" Gray 1

11 920001 Nut, 10-32 Nyloc Stop 152 962162 Screw, #10 x 1/2 FHP HILO Zinc 3

12 509830 Washer, Handle Tube 1 53 502110 Clip, Bumper 3

13 503320 Flange, Strain Relief 154 962018 Screw, 3/8-16 x 2 HH Zinc 4

14 505720 Nipple, Handle 255 915001 Key, 3/16 x 2 7/8L 1

15 481310C Switch Box 156 980009 Washer, 3/8 Lock 4

16 515150 Label, Warning 1 57 962048 Screw, 3/8-16 1 1/4 HH 4

17 501210 Bumper, Handle 1 58 506980 Pulley, Motor 1

18 962003 Screw, 10-32 x 3/4 PHP 1 59 506994 Pulley, Pad 1

19 962006 Screw, 1/4-20 x 1/2 PHP SS 7 60 903005 Belt, 1500 RPM 1

503711 Grip, Handle, Gray 2 61 962073 Screw, 1/4-20 x 5/8 Soc Set 2

501501 Cap, Protective End 262 503382 Flange, Flex Pad Driver 1

21 980015 Washer, #10 External Tooth 2 63 962036 Screw, 1/4-20 x 1 FHP 6

508520 Strain Relief, Complete 164 962014 Screw, 5/16-18 x 3/4 1

502020 Clamp, Strain Relief 165 980006 Washer, 5/16 Lock 1

23 962015 Screw, 10-32 x 3/8 PHP 2 66 504471 Pad Holder Assembly 1

24 502422 Cord Assembly, 50' 167 962076 Screw, #8 x 5/8 PHP 3

25 509082 Tube, Handle 168 509780 Wheel, 4" Gray Non-Marking 2

26 504420 Hook, Cord 169 487202 Retainer, Axle 1

27 962005 Screw, 1/4-20 x 3/8 Set 1 70 507781 Shaft, Wheel 2

28 505010 Knob, Turn 1 71 980005 Washer, Wave 8

29 980007 Washer, 5/16 Flat 2 72 509820 Washer, Fiber 12

30 500880 Brace, Handle 2 73 507320 Ring, Snap 4

31 908008 Handle Cord Assembly 174 962161 Screw, 10 x 3/4 PHP HILO 2

32 502021 Clamp, Handle 1 75 508080 Strap, Bumper, 51" 1

33 962009 Bolt, 5/16-18 x 2 1/2 Carriage 1 76 962016 Screw, 10-32 x 3/8 Set 1

34 507481 Rod, Brace 177 509781 Wheel, 5" Gray Non-Marking 2

35 507310 Ring, 3/8 Snap 1

36 509920C Yoke 1Labels Not Shown:

37 507480 Rod, Yoke 1485106 Label, Handle Warning 1

38 962161 Screw, 10 x 3/4 PHP HILO 3 506318 Label, Interlock 1

39 502319 Cover, Bearing 1506340 Label, Brush Indicator 1

40 962026 Screw, 8-32 x 1/2 Type F 3

505181 Light, Brush Wear Indicator 115V 1

505182 Light, Brush Wear Indicator 220V 1

B-1500 BURNISHER MOTOR PARTS LIST

ITEM PART NO. DESCRIPTION QTY.

505286 Motor 115V, 1.5HP 1

505278 Motor 220V, 1.5HP 50C 1

A502919 End Bell - Motor LOWER 1

B500417 Armature Asm.w/Bearings,115V 1

500424 Armature Asm.w/Bearings, 220V 1

902012 Bearing, Motor Lower 1

CField & Shell Assembly 1

D902003 Bearing, Motor Top 1

E500903 Carbon Brush, Motor 115V 4

510901 Carbon Brush, Motor 220V 4

F507322 Brush Ring Asm. Complete, 115V 1

507326 Brush Ring Asm. Complete, 220V 1

GEnd Bell - Motor TOP 1

I960018 Bolt, Motor Thru 4

J911048 Rectifier, 115V 1

911081 Rectifier, 220V 1

K908024 Cord Assembly, Motor 1

B-1500 BURNISHER WIRING DIAGRAM

WARRANTY POLICY

BURNISHER, MODEL B-1500, ABS BASE

The Pacic Floorcare B-1500 Burnisher has been manufactured, tested and inspected in accordance with specic engineering

requirements and is WARRANTED to be free from defects in workmanship and materials as follows:

Eighteen (18) months parts, One (1) year labor - DC Motors (except recer and carbon brushes)

One (1) year parts and labor – All other components unless excluded below.

This warranty extends to the original user/purchaser and only when used, operated and maintained in accordance with Pacic

Operang and Maintenance instrucons.

This warranty does not apply to the following wear parts and accessories of the machine including:

Part Number

502422

509780

509781

503711

501286

903005

500903

Nor does it apply to damage or failure caused by improper use, abuse or neglect. Warranty credit or replacement of return

parts including motors, etc., is subject to incoming inspecon of those items.

To secure repair under this warranty, the following procedure should be taken:

• The inoperave machine or warranted parts must be delivered to the authorized dealer with shipping and delivery charges

prepaid. If unable to locate the Dealer, you may contact Pacic at the address listed herein for the locaon of the nearest

Pacic repair center or agent or for other instrucons pertaining to your warranty diculty.

• Upon compliance with the above warranty procedure, all warranted repairs would be completed at no addional charge

or cost to the user.

• Only Pacic or its authorized dealers and agents may make no charge warranty repairs on this product. All others do so

at their own risk.

This warranty limits Pacic liability to the repair of the product and/or warranted parts replacement and does not include

incidental or consequenal damages arising from the use of a Pacic machine whether defecve or not.

This warranty is in lieu of all other expressed or implied warranes and is extended to the original purchaser/user.

2259 S. SHERIDAN DRIVE

MUSKEGON, MICHIGAN 49442-6252

800-968-1332

FAX 800-863-9536

10/12

Part Name

Cord Assembly

Wheel, 4”

Wheel, 5”

Handle Grip, Grey

Bumper Base

Belt

Carbon Brush, 115V Motor

Andere Handbücher für B-1500

Inhaltsverzeichnis

Andere Pacific Bodenreinigungsmaschine Handbücher

Pacific

Pacific FM-17EHD Bedienungsanleitung

Pacific

Pacific Floormaster 18B Installations- und Betriebshandbuch

Pacific

Pacific FURY 20BB Installations- und Betriebshandbuch

Pacific

Pacific FM-17 EHD Bedienungsanleitung

Pacific

Pacific Z26T Bedienungsanleitung

Pacific

Pacific B-1500 Bedienungsanleitung

Pacific

Pacific FURY 1500DCP Bedienungsanleitung

Pacific

Pacific 545411 Bedienungsanleitung

Pacific

Pacific Proteus 26 Installations- und Betriebshandbuch

Pacific

Pacific FURY 21 HSB Installations- und Betriebshandbuch

Pacific

Pacific FURY 1500P Bedienungsanleitung

Pacific

Pacific FM-17HD Bedienungsanleitung

Pacific

Pacific TRIUMPH 1190 Handbuch

Pacific

Pacific FM-17DS Bedienungsanleitung

Pacific

Pacific B-1500 Bedienungsanleitung

Pacific

Pacific Z26BA Bedienungsanleitung

Pacific

Pacific 2000 DCP Installations- und Betriebshandbuch

Pacific

Pacific MINISWEEP Installations- und Betriebshandbuch

Pacific

Pacific Z20BA Bedienungsanleitung

Pacific

Pacific S-20 Bedienungsanleitung

Pacific

Pacific Z20T Bedienungsanleitung

Pacific

Pacific SANISWEEP Installations- und Betriebshandbuch

Pacific

Pacific TIGERRAY 21 Installations- und Betriebshandbuch

Pacific

Pacific ScrubMaster 32B Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch