Panasonic WV-QDC500S Bedienungsanleitung
For U.S. and Canada:
Panasonic i-PRO Sensing Solutions
Corporation of America
800 Gessner Rd, Suite 700 Houston, TX 77024
https://www.security.us.panasonic.com/
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada
1-877-495-0580
https://www.panasonic.com/ca/
© Panasonic i-PRO Sensing Solutions Co., Ltd. 2020
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic i-PRO Sensing Solutions Co., Ltd.
Fukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Operating Instructions
Included Installation Instructions
Dome Cover
Model No.
WV-QDC500S
• Before attempting to connect or install this product, please read these instructions carefully and
save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product
within the scope that will not interfere with normal use due to improvement of the product.
Ns0620-0
Printed in China
Preface
This smoke type dome cover (approx. 45 % of transmittance) is used to install the indoor/outdoor
use dome-type monitoring camera.
For the latest information about the supported cameras, refer to our support website
(https://security.panasonic.com/training_support/support/info/ <Control No.: C0501>).
Specifications
Ambient operating temperature: –30 °C to +50 °C {–22 °F to +122 °F}
Mass: Approx. 20 g{0.04 lbs}
Dimensions: Diameter: 71.0 mm {2-25/32 inches}
Height: 37.5 mm {1-15/32 inches}
Diameter of the dome: 30.5 mm {1-3/16 inches}
Precautions
■ Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product.
Be sure to consult the dealer.
Standard accessories
Operating instructions (this document)....................................................................................... 1 pc.
Installation
Read the following descriptions together with the Installation Guide of the camera.
Note:
• When a smoke type dome cover is used, the IR LED irradiation distance and the illuminance
level are lower than for a standard clear type dome cover.
Check the settings after attaching the enclosure.
Step1
Loosen enclosure fixing screws (3 places),
and remove the enclosure from the camera.
<Outdoor camera>
Loosen the screws using the bit (camera accessory).
<Indoor camera>
Loosen the screws using a Phillips screwdriver.
* The right illustrations are examples of outdoor use
camera.
Step2
Remove the dome cover.
q Remove the fixing screws (3 pcs.) that secure the dome cover anchor bracket to the enclosure.
w
Remove the dome cover anchor bracket , the dome cover and rubber ring (outdoor camera only).
Note:
• These fixing screws
(3 pcs.)
, the dome cover anchor bracket and rubber ring (outdoor camera
only) will be used again in step3.
Bit (camera accessory) Enclosure
Enclosure fixing
screw (3 places)
<Outdoor camera> <Indoor camera>
Dome cover
anchor bracket
Dome cover
Fixing screw
(3 pcs.)
Enclosure
Rubber ring
Dust guard
sponge
Step3
Replace the dome cover.
q Remove the cover film from the outside of the dome cover (this product). Keep the removed
cover film for following step. (Take care not to damage the outside or inside of this product.)
w Attach the rubber ring to the enclosure. (Outdoor camera only)
e Attach this product to the enclosure.
r Using the fixing screws (3 pcs.) that were removed in step2, secure the dome cover anchor
bracket to the enclosure. (Recommended tightening torque: 0.40 N·m {0.30 lbf·ft})
t Attach the cover film removed in qto the outside surface of this product.
Note:
• When attaching, make sure that the rubber ring is properly set in the groove of the enclosure.
(Outdoor camera only)
• Do not remove the dust guard sponge adhered to the dome cover anchor bracket.
(Indoor camera only)
Step4
Attach the enclosure to the camera.
Tighten the enclosure fixing screws (3 places) using the bit (camera accessory) or Phillips screw-
driver.
Recommended tightening torque: 0.70 N·m {0.52 lbf·ft}
Refer to the Installation Guide of the camera for more information about installing the camera.
<Outdoor camera> <Indoor camera>
Dome cover
anchor bracket
Dome cover
Fixing screw
(3 pcs.)
Enclosure
Rubber ring
Dust guard
sponge
Andere Panasonic Kamerazubehör Handbücher
Panasonic
Panasonic YAX800G Bedienungsanleitung
Panasonic
Panasonic AJ-HVF20P Bedienungsanleitung
Panasonic
Panasonic HHR380A Bedienungsanleitung
Panasonic
Panasonic WVRM70 - ACCESSORY Bedienungsanleitung
Panasonic
Panasonic WV-CF5S Bedienungsanleitung
Panasonic
Panasonic WV7225 - PANA TILT Bedienungsanleitung
Panasonic
Panasonic Lumix H-FS014045 Bedienungsanleitung
Panasonic
Panasonic WVPS104C - CAMERA DRIVE UNIT Bedienungsanleitung
Panasonic
Panasonic AJ-CA905G Bedienungsanleitung
Panasonic
Panasonic H-NS043 Bedienungsanleitung
Panasonic
Panasonic DMW-DCC11 Bedienungsanleitung
Panasonic
Panasonic LUMIX DMW-MCTZ7 Bedienungsanleitung
Panasonic
Panasonic POH1000 Bedienungsanleitung
Panasonic
Panasonic POH1000 Bedienungs- und Montageanleitung
Panasonic
Panasonic WV-Q175E Bedienungsanleitung
Panasonic
Panasonic VariCam AU-VREC1G Bedienungsanleitung
Panasonic
Panasonic VRLA Bedienungsanleitung
Panasonic
Panasonic AWRP120GJ Bedienungsanleitung
Panasonic
Panasonic LC-R063R4P Bedienungsanleitung
Panasonic
Panasonic Lumix H-HS35100 Bedienungsanleitung
