Panasonic AJHDP2000 - 2K PROCESSOR Bedienungsanleitung

2K Processor

Operating Instructions

Model No. AJ-HDP2000P

Before operating this product, please read the instructions carefully and save this manual for future use.

F0707N0 -F @

Printed in Japan VQT1F04

ENGLISH

Read this first

indicates safety information.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD AND ANNOYING INTERFERENCE,

USE THE RECOMMENDED ACCESSORIES

ONLY.

FCC Note:

This equipment has been tested and found to comply

with the limits for a class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference when the equipment is operated in a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy, and if not

installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

Warning:

To assure continued FCC emission limit compliance, the

user must use only shielded interface cables when

connecting to external units. Also, any unauthorized

changes or modifications to this equipment could void

the user’s authority to operate it.

CAUTION:

In order to maintain adequate ventilation, do not

install or place this unit in a bookcase, built-in

cabinet or any other confined space. To prevent risk

of electric shock or fire hazard due to overheating,

ensure that curtains and any other materials do not

obstruct the ventilation.

CAUTION:

KEEP THE TEMPERATURE INSIDE THE RACK

BETWEEN 41°F to 104°F (5°C to 40°C).

zBOLT THE RACK SECURELY TO THE FLOOR

SO THAT IT WILL NOT TOPPLE OVER WHEN

THE UNIT IS DRAWN OUT.

CAUTION:

The mains plug of the power supply cord shall

remain readily operable.

The AC receptacle (mains socket outlet) shall be

installed near the equipment and shall be easily

accessible. To completely disconnect this

equipment from the AC mains, disconnect the mains

plug from the AC receptacle.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, REFER CHANGES OF SWITCH

SETTINGS INSIDE THE UNIT TO QUALIFIED

SERVICE PERSONNEL.

_DO NOT REMOVE PANEL COVERS BY

UNSCREWING THEM.

To reduce the risk of electric shock, do not remove

the covers. No user serviceable parts inside.

Refer servicing to qualified service personnel.

_THIS EQUIPMENT MUST BE GROUNDED

To ensure safe operation, the three-pin plug must be

inserted only into a standard three-pin power outlet

which is effectively grounded through normal

household wiring. Extension cords used with the

equipment must have three cores and be correctly

wired to provide connection to the ground. Wrongly

wired extension cords are a major cause of fatalities.

The fact that the equipment operates satisfactorily

does not imply that the power outlet is grounded or

that the installation is completely safe.

For your safety, if you are in any doubt about the

effective grounding of the power outlet, please

consult a qualified electrician.

WARNING:

zTO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS

EQUIPMENT TO RAIN OR MOISTURE.

zTO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, KEEP THIS EQUIPMENT AWAY

FROM ALL LIQUIDS. USE AND STORE ONLY

IN LOCATIONS WHICH ARE NOT EXPOSED

TO THE RISK OF DRIPPING OR SPLASHING

LIQUIDS, AND DO NOT PLACE ANY LIQUID

CONTAINERS ON TOP OF THE EQUIPMENT.

Table of Content

Read this first! ............................................................................................... 2

Operating Precautions ................................................................................. 4

Overview/Features ........................................................................................ 5

1. Overviews ........................................................................................................5

2. Features ..........................................................................................................5

2.1. Compression .............................................................................................5

2.2. VTRs Migration .........................................................................................5

2.3. Dual-Link SDI & I/O ...................................................................................5

2.4. Maximum Record Time .............................................................................5

2.5. Indicator Display ........................................................................................5

2.6. Compact and Lightweight ..........................................................................5

Controls and their Functions ....................................................................... 6

1. Front Panel ......................................................................................................6

2. Connector Section (Rear) ................................................................................7

3. I/Os ..................................................................................................................8

3.1. VIDEO Input ..............................................................................................8

3.2. VIDEO Output ...........................................................................................8

3.3. AUDIO Input ..............................................................................................9

3.4. AUDIO Output ...........................................................................................9

3.5. TC (Time Code) Input ...............................................................................9

3.6. TC (Time Code) Output .............................................................................9

3.7. META DATA Input ...................................................................................10

3.8. META DATA Output ................................................................................10

3.9. Other I/Os (HD REF IN, VTR I/F) ............................................................10

3.10. Service Only (15 Pin) ..............................................................................10

2K Processor & HD-D5 VTR System Connections .................................. 11

Connection with existing systems ............................................................ 12

Indicator Display (Front Panel LED) .......................................................... 13

Connection Check ...................................................................................... 14

Service Switch (Rear) ................................................................................. 14

Power On ..................................................................................................... 14

Restrictions ................................................................................................. 15

Rack Mounting ............................................................................................ 17

Specifications .............................................................................................. 18

Operating Precautions

_Power supply

Use an AC 120 V (U.S.A. and Canada) power supply.

zBe sure to take hold of the power plug when connecting and

disconnecting the power cable.

zDo not run the power cable near a heating source.

zDo not place heavy objects on top of the power cable.

zDo not tamper with the power cable in any way.

_No insertion of foreign matters

Do not insert or drop metal or any foreign objects into the unit’s

openings (such as the fan vents).

Foreign objects inside the unit can cause a fire or short circuits.

Contact the dealer for assistance.

_No disassembly

High voltage is supplied to some parts inside the unit, and

touching these parts is not only dangerous but may cause a

malfunction.

Leave all internal insections and adjustments to the dealer from

whom you purchased the unit.

_DANGER: No operation if unit is

malfunctioning

If smoke comes out or strange sounds or smells are detected

from the unit, ask the dealer from whom you purchased the unit

for repairs.

Overview/Features

1. Overviews

This new 2K Processor (AJ-HDP2000) for the HD-D5 VTRs (AJ-HD3700H*1, AJ-HD3700A*1, AJ-HD3700B*2)

is designed for post-production and telecine systems, and this new technology provides a cost-effective and

efficient method of recording, editing and archiving full-size 2K and 4:4:4 HDTV images on the film post-

production standard D-5 mastering video tape recording system.

The 2K Processor allow professionals to record full 12-bit 4:4:4 “2K” 2048

1080 resolution film image data, or

12-bit 4:4:4 sampled 1920

1080 HD images onto Panasonic’s AJ-HD3700H, AJ-HD3700A or AJ-HD3700B

HD-D5

VTRs for editing, archiving, and distribution, a process that formerly was not easily achievable.

*1The software must be upgraded. For details, contact the dealer where you purchased the product.

*2The software for some VTRs must be upgraded. For details, contact the dealer where you purchased the

product.

2. Features

2.1. Compression

The 2K Processor uses JPEG2000 compression,

the similar compression scheme specified by the

Digital Cinema Initiative (DCI) for cinema release,

to convert film to digital data for subsequent

processing in advanced DI environments while

maintaining its resolution. The processor's

advanced encoder ensures that images remain

faithful throughout the recording process, and

minimizes distortion and resolution degradation

and offers optimized bit rate control and increased

error tolerance for the reliable interchange required

for editing.

2.2. VTRs Migration

The numerous Post facilities with capital

investments in D-5 will be able to use their current

AJ-HD3700 series, and the workflow that has

worked so well for them with existing HD-D5 VTRs

can be continued with a simple software upgrade

for 2K and HD post-production.

2.3. Dual-Link SDI & I/O

For ease of monitoring and interfacing with more

traditional high definition equipment, The 2K

Processor has added a 4:4:4 to 4:2:2 conversion

capability. The full audio capability of the D-5

format is maintained, including eight-channel 24-bit

recordings, as well as the ability of the system to

handle compression audio streams for multi-

channel / second language applications. Audio I/O

is by means of embedded HD-SDI or HD-D5 VTR’s

AES/EBU inputs, analog inputs. Interconnection

from the processor to the HD-D5 VTR is by

mapped compressed data over the HD-D5 VTR’s

existing HD-SDI input / outputs. The processor

accepts dual link SMPTE 372M video / 2K inputs.

Time Code in/out is embedded or HD-D5 VTR’s

XLR.

2.4. Maximum Record Time

Maximum recording time is 155 minutes, the same

as the HD-D5 VTR’s 24fps modes.

2.5. Indicator Display

Alarm indicator (RED):

When flashing, indicates that some errors

have occurred.

When lit constantly, indicates a serious

problem such as the fan has stopped or the

rear service switch is ON.

2048/1920 indicator (GREEN):

Indicates the Horizontal sample number of

System settings.

2.6. Compact and Lightweight

With a height of 2U and weight of 7.5 kg (16.5 lb),

this compact and lightweight unit can be

transported easily.

Controls and their Functions

1. Front Panel

!1" Power Lamp This lights when the power is turned on.

!2" Power Switch When the ON side is pressed, the power is turned on; when

the OFF side is pressed, the power is turned off.

| : Press the “ | ” side of the power switch to turn the power

on.

±:Press the “ ±” side of the power switch to turn the power

off.

!3" Alarm Lamp This lights when a problem has occurred in the main unit,

making it impossible to guarantee operation. (Refer to the

messages on page 13.)

!4" Horizontal Sample Display Lamp This displays the H sample of the video signal that is system

setting.

!2"!1" !3" !4"

Controls and their Functions (Continued)

2. Connector Section (Rear)

!1" AC Input Socket Use the accessory power cord to connect the socket to the power outlet

!2" Fuse Power circuit fuse

!3" GND (ground) Terminal When connected with another unit, the unit must be ground here

!4" Dual-Link SDI Input For inputting the Dual-Link digital signals

!5" Dual-Link SDI Output 1, 2 For outputting the Dual-Link or HD digital signals

(4:4:4/4:2:2 switchable)

!6" HD-SDI Monitor Output For outputting the HD digital signals (4:2:2 samples)

!7" Serial Data input (HD-SDI) This is connected to the HD SDI OUT connector on the HD-D5 VTR for

inputting for video/ audio/ tc output data from the HD-D5 VTR.

!8" Serial Data Output (HD-SDI) This is connected to the HD SDI IN connector on the HD-D5 VTR for

outputting the video/ audio/ tc data.

!9" HD SYNC OUT This is connected to the REF IN HD connector on the HD-D5 VTR.

The sync signal re-generated from the HD REF IN signal of the

processor.

!10" HD REF IN For inputting the tri-level sync signals as reference signals

!11" HD Reference Through Output

(Auto Terminated)

This is through output of input reference signal

!12" Service Switch

(only Use Service Maintenance)

This slide switch is used only in service mode.

Please Slide OFF for Normal Operation.

!13" SERVICE ONLY (RS-232C)

<15pin>

(only Use Service Maintenance)

This connector is used only in service mode.

!9"!8"!7"!6" !2"!11"!13"!12" !10" !1" !3"!4" !5"

Controls and their Functions (Continued)

3. I/Os

3.1. VIDEO Input

zThe following two VIDEO input signals are supported.

1920 a1080/23.98PsF, 24PsF XYZ/RGB 4:4:4 12 bits

2048 a1080/23.98PsF, 24PsF XYZ/RGB 4:4:4 12 bits

zThe color space signal format is selected from the following two types in FRONT MENU of the HD-D5 VTR.

SYSTEM settings for the RGB and XYZ color spaces

RGB: Mode for recording and playback RGB color space

XYZ: Mode for recording and playback XYZ color space

3.2. VIDEO Output

zThere are three types of VIDEO output signals, and output signals are set in SYSTEM FORMAT in FRONT

MENU of the HD-D5 VTR.

1920 a 1080/23.98PsF, 24PsF XYZ/RGB 4:4:4 12/10 bits

2048 a 1080/23.98PsF, 24PsF XYZ/RGB 4:4:4 12/10 bits

1920 a 1080/23.98PsF, 24PsF YPbPr 4:2:2 10 bits

zThe main output is available in 4:2:2 format a 4 lines.

zBoth main output and monitor output have the Dynamic Rounding function when 10-bit output is selected.

zThe VANC/HANC data, such as Audio/TC/Meta/Payload information, is not embedded on the OUTPUT MON

(Monitor) output.

zIn OUTPUT MON (Monitor) and when the 4:2:2 format is selected for the main system, an H CROP function for

1920 samples is available in 2048 samples. However, the Squeeze and Letter Box functions are not available.

The following three kinds of modes are available as fixed Crop modes.

CTR Crop: Both sides are equally cropped so that the number of samples is 1920.

L Crop: The left side is cropped so that the number of samples is 1920.

R Crop: The right side is cropped so that the number of samples is 1920.

zOUTPUT MON (Monitor) has a function to turn on/off superimposition in SUPER.

Name Video Input Signal

INPUT A

INPUT B

Dual Link SDI Input BNC a2, 75 Ω

1920 a 1080/23.98, 24PsF XYZ/RGB 4:4:4

SMPTE 372M/291M/292M/299M standard

2048 a1080/23.98, 24PsF XYZ/RGB 4:4:4

Name Video Output Signal

OUTPUT 1A

OUTPUT 1B

Dual Link SDI Output BNC a2 a2, 75 Ω

1920 a 1080/23.98, 24PsF XYZ/RGB 4:4:4

SMPTE 372M/291M/292M/299M standard

OUTPUT 2A

OUTPUT 2B

2048 a1080/23.98, 24PsF XYZ/RGB 4:4:4

1920 a 1080/23.98, 24PsF YPbPr 4:2:2

SMPTE 291M/292M/299M standard

OUTPUT MON Single HD SDI Monitor Output BNC a1, 75 Ω(Super ON/OFF)

1920 a 1080/23.98, 24PsF YPbPr 4:2:2

SMPTE 292M standard

(Video Signal only w/o ANC data)

Controls and their Functions (Continued)

3.3. AUDIO Input

zFor AUDIO input, an SDI Embedded Audio function is available with the 2K processor, and AES/EBU Digital

Audio, Analog Audio, and CUE Audio inputs are available from the HD-D5 VTR in a manner similar to the single

operation of the HD-D5 VTR.

zThe AUDIO input signal is selected in FRONT MENU of the main unit in a manner similar to the single

operation of the HD-D5 VTR.

zSDI Embedded Audio input signals are available only for Ach of Dual Link SDI signals.

3.4. AUDIO Output

zFor AUDIO output, an SDI Embedded Audio function is available with the 2K processor, and AES/EBU Digital

Audio, Analog Audio, and CUE Audio outputs are available from the HD-D5 VTR in a manner similar to the

single operation of the HD-D5 VTR.

zThe AUDIO output signal is selected in FRONT MENU of the HD-D5 VTR in a manner similar to the single

operation of the HD-D5 VTR.

zSDI Embedded Audio output signals are available only on Ach of Dual Link SDI signals.

zSDI Embedded Audio signals are not available on OUTPUT MON (Monitor).

3.5. TC (Time Code) Input

zFor TC input, an SDI Embedded HANC TC function is available with the 2K processor, and the LINEAR TC

input is available from the HD-D5 VTR in a manner similar to the single operation of the HD-D5 VTR.

zFor SDI Embedded HANC TC input signals, only Ach of Dual Link SDI signals is supported.

zLTC or VITC can be selected as a SDI Embedded HANC TC input signal.

zThe TC input signal is selected in FRONT MENU of the HD-D5 VTR in a manner similar to the single operation

of the HD-D5 VTR.

3.6. TC (Time Code) Output

zFor the TC output, an SDI Embedded HANC TC function is available with the 2K processor, and the LINEAR

TC output is available from the HD-D5 VTR in a manner similar to the single operation of the HD-D5 VTR.

zSDI Embedded HANC TC output signals are available only on Ach of Dual Link SDI signals.

zSDI Embedded HANC TC signals are not available on the OUTPUT MON (Monitor).

Audio Input Signal

Dual Link SDI Input

(Embedded Audio)

BNC a2, 75 Ω

SMPTE 299M standard

Audio Output Signal

Dual Link SDI Output

(Embedded Audio)

BNC a2 a2, 75 Ω

SMPTE 299M standard

TC Input Signal

Dual Link SDI Input

(Embedded LTC/VITC)

BNC a2, 75 Ω

SMPTE 291M standard

TC Output Signal

Dual Link SDI Output

(Embedded LTC/VITC)

BNC a2 a2, 75 Ω

SMPTE 291M standard

Controls and their Functions (Continued)

3.7. META DATA Input

zFor META DATA input, an SDI Embedded VANC function is available with the 2K processor, only Y signals in

Ach of Dual Link SDI signals are supported.

zMETA DATA can record up to 2,880 words per segmented frame.

The capacity of 2,880 words is the upper limit even when data exceeds the capacity (the same as single

operation of the HD-D5 VTR in the specifications).

3.8. META DATA Output

zFor META DATA output, an SDI Embedded VANC function is available with the 2K processor, and META DATA

signals are embedded only on Y signals in Ach of Dual Link SDI signals.

zMETA DATA output is embedded up to 2,880 words per segment frame on Y signals, where data is entered

from the head (the same as single operation of the HD-D5 VTR in specification).

zMETA DATA signals are not embedded on the OUTPUT MON (Monitor).

3.9. Other I/Os (HD REF IN, VTR I/F)

zThe reference input of the HD REF IN is only accepted tri-level signals of HD (1920 a 1080/23.98, 24PsF).

Loop-through output is available.

zBe sure to connect the HD SYNC OUT to the HD REF IN of the HD-D5 VTR to supply the tri-level signals of HD

(1920 a1080/23.98, 24PsF) from 2K Processor.

zBe sure to connect the SERIAL DATA OUT to the HD SDI IN of the HD-D5 VTR.

zBe sure to connect the SERIAL DATA IN to one of the HD SDI OUT1, OUT2 or OUT3 of the HD-D5 VTR.

3.10.Service Only (15 Pin)

Not applicable.

Terminal name Other Input and Output

HD REF IN HD Reference Input BNC a2 (loop-through a1),

75 Ωautomatic termination

HD (1920 a 1080/23.98, 24PsF) tri-level sync

HD SYNC OUT HD SYNC Output BNC a1, 75 Ω

HD (1920 a 1080/23.98, 24PsF) tri-level sync

Advanced Reference signal for the HD-D5 VTR

SERIAL DATA OUT VTR HD_SDI Output BNC a1, 75 Ω

1920 a 1080/23.98, 24PsF

SMPTE 292M compliance

SERIAL DATA IN VTR HD_SDI Input BNC a1, 75 Ω

1920 a 1080/23.98, 24PsF

SMPTE 292M compliance

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Computerhardware Handbücher

Panasonic

Panasonic CF-BAW0512AU Bedienungsanleitung

Panasonic

Panasonic AJ-YA93 Bedienungsanleitung

Panasonic

Panasonic AJ-YA931G Bedienungsanleitung

Panasonic

Panasonic MICROCOMPUTER MN103S Montage- und Bedienungsanleitung

Panasonic

Panasonic CY-EM100N Bedienungsanleitung

Panasonic

Panasonic CF-BAW1024AU Bedienungsanleitung

Panasonic

Panasonic FZ-VCN401 Bedienungsanleitung

Panasonic

Panasonic 2SC2631 Bedienungsanleitung

Panasonic

Panasonic MTM86628 Bedienungsanleitung

Panasonic

Panasonic TY-42TM6B - Monitor Terminal Expansion Board Benutzerhandbuch

Panasonic

Panasonic AJ-YA94G Bedienungsanleitung

Panasonic

Panasonic ET-MDNHM10C Bedienungsanleitung

Panasonic

Panasonic AW-360B10 Bedienungsanleitung

Panasonic

Panasonic CF-VEB471 Bedienungsanleitung

Panasonic

Panasonic WJMPU955A - CENTRAL PROCESSING UNIT Bedienungsanleitung

Panasonic

Panasonic WJ-HXE400 Bedienungsanleitung

Panasonic

Panasonic 2SA2163 Bedienungsanleitung

Panasonic

Panasonic 2SC1318A Bedienungsanleitung

Panasonic

Panasonic WJ-PB85T08 Bedienungsanleitung

Panasonic

Panasonic 2SC4691G Bedienungsanleitung

Panasonic

Panasonic UP05C8PG Bedienungsanleitung

Panasonic

Panasonic PanaXSeries MN103S65G Bedienungsanleitung

Panasonic

Panasonic Panaboard UB-5310 Bedienungsanleitung

Panasonic

Panasonic KX-TDA6181X Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung