Panasonic ES8113 Bedienungsanleitung
English 2
中文 7
Operating Instructions
使用说明书
AC/Rechargeable Shaver
交流 / 充电式剃须刀
Model No.
型号 ES8113
Before operating this unit, please read these instructions completely and save them.
在使用本产品前，请仔细阅读本说明书并妥善保管。
ES8113_CH.indb 1 2007/07/11 9:23:52
2
English
Important
Using the shaver
Caution - The outer foil is very thin and can be damaged if not
used correctly. Check that the foil is not damaged before using
the shaver. Do not use the shaver if the foil etc. is damaged as
you will cut your skin.
Charging the shaver
Do not use any power cord or AC adaptor other than one
specifically designed for this model.Plug in the adaptor into a
household outlet where there is no moisture and handle it with
dry hands.The shaver may become warm during use and
charging. However, this is not a malfunction. Do not charge the
shaver where it will be exposed to direct sunlight or other heat
sources.Hold the adaptor when disconnecting it from the
household outlet. If you tug on the power cord, you may damage
it. Contact an authorized service center if the power cord gets
damaged.
Adequate ambient temperature for charging is 15-35 °C.
If the indicators on the LCD panel do not glow, wait for a short
while until it glows.
Cleaning the shaver
Warning - Disconnect the power cord from the shaver before
cleaning it to prevent electric shock.
Keep both the inner blades inserted. If only one of the inner
blades is inserted, the shaver may be damaged.If you clean the
shaver with water, do not use salt water or hot water. Do not
soak the shaver in water for a long period of time.Wipe it with a
cloth dampened with soapy water. Do not use thinner, benzine
or alcohol.
Storing the shaver
Disconnect the power cord when storing the shaver.Do not
bend the power cord or wrap it around the shaver. Do not leave
this shaver within the reach of small children. Keep these
operating instructions in a safe place.
SPECIFICATIONS
Model: ES8113
Rated input: a.c 100-240 V, 150 mA
Rated output: d.c 5.7 V, 1.0 A
Charging time: 1 hour
This product is intended for household use only.
The unit is applied to the Chinese standard GB4706.1 appendix
B, GB4706.9 and Q/(GZ) PEWWBG 6.
Parts identification
Protective cap
Foil frame
3System outer foil
4System outer foil
release buttons
5Inner blades
6Foil frame release
buttons
7Finger rest
8Pivot action
selector
90/1 switch
LCD panel
Appliance socket
Trimmer
Trimmer handle
Adaptor (RE7-40)
Power cord
Appliance plug
Soft case
Cleaning brush
Oil
•
ES8113_CH.indb 2 2007/07/11 9:23:53
3
English
Charging
Charge
1
1Insert the appliance plug
into the shaver.
2
2Plug in the adaptor into a
household outlet.
The indicators on the LCD panel glow
and charging starts.
Charging is completed when the
indicators on the LCD panel blink.
(Max. 1 hour later)
•
•
Cord shaving
If you insert the appliance plug to the shaver and plug in the
adaptor into a household outlet, you can use it even if the battery
capacity is low.
If the shaver does not work, continue charging it for approx.1
minute.
•
About the LCD panel
The LCD panel shows the remaining battery capacity from 0% to
100%, in 10% increments.
While charging After charging is
completed
10 minutes after
charging is
completed
The indicators
glow.
The indicators
blink once every
second.
The indicators blink
once every 2
seconds.
When the battery capacity is low
You can shave 1 to 2 times after “10%”appears.
(This will differ depending on usage.)
•
“10%” appears and blinks.
A full charge will supply enough power for approx. 14 shaves of
3 minutes each.
•
Using the trimmer
Slide the trimmer handle up.Place
at a right angle to your skin and
move downwards to trim your
sideburns.
ES8113_CH.indb 3 2007/07/11 9:23:53
4
English
Using the shaver
Shave
90˚
1
1Press the 0/1
switch. 2
2Hold the shaver as
illustrated above and
shave.
Start out shaving by applying gentle pressure to your face.
Stretch your skin with your free hand and move the shaver
back and forth in the direction of your beard.You may gently
increase the amount of pressure as your skin becomes
accustomed to this shaver. Applying excessive pressure does
not provide a closer shave.
•
Pivot action selector
Use to select “SOFT”(soft) or “LOCK”
(lock).
You can change the pivot action whether
the shaver is turned on or off.
SOFT
LOCK
Cleaning
Clean
We recommend that you clean your
shaver with the “sonic”vibration
turbo-cleaning mode when the faucet
symbol appears on the LCD
panel.
1. Disconnect the power cord from
the shaver.
2. Apply some hand soap and some
water to the outer foil.
3. Press the 0/1 switch for more than
2 seconds to activate the turbo
mode for “sonic” vibration
cleaning.
appears on the LCD panel.
After about 20 seconds, it will be
automatically turned off, or you
can turn it off by pressing the 0/1
switch.
4. Remove the system outer foil and
press the 0/1 switch for more than
2seconds to activate the turbo
mode for “sonic” vibration cleaning
and clean it with running water.
5. Wipe off any drops of water with a
dry cloth.
6. Remove the system outer foil and
the foil frame to allow them to dry
completely.
The mark on the left
is for a washable
shaver and indicates
it can be cleaned
with water.
•
•
ES8113_CH.indb 4 2007/07/11 9:23:55
5
English
Caution for turbo mode
Shaving in turbo mode may damage your skin.Turn the shaver
off and then on again to cancel turbo mode.
Do not place your fingers on the 0/1 switch while using the
shaver.This may cause the shaver to turn off or enter turbo
mode.Place your fingers on the finger rest while using the
shaver.
•
•
Lubrication
To maintain shaving comfort for a long time, it is recommended
that the oil provided with the shaver is used.
1. Switch off the shaver.
2. Apply one drop of oil to each of the outer foils.
3. Raise the trimmer and apply a drop of oil.
4. Switch the shaver on, and run it for approximately five
seconds.
5. Switch off the shaver, and wipe off any excess oil from the
outer foils with a soft cloth.
Replacing the system outer foil and the inner
blades
system outer foil once every year
inner blade once every two years
Replacing the system outer foil
1. Press the foil frame release
buttons and lift the system
outer foil upwards as
illustrated.
2. Press the system outer foil
release buttons and pull down
the system outer foil as
illustrated.
3. Insert the system outer foil
until it clicks.
Always attach the system
outer foil in proper direction.
Always insert the system
outer foil to the foil frame
when attaching to the shaver.
•
•
2 3
ES8113_CH.indb 5 2007/07/11 9:23:55
6
English
Replacing the inner blades
1. Press the foil frame release
buttons and lift the system
outer foil upwards as
illustrated.
2. Remove the inner blades one
at a time as illustrated.
Do not touch the edges
(metal parts) of the inner
blades to prevent injury to
your hand.
3. Insert the inner blades one at
a time until they click as
illustrated.
•
2 3
Cleaning with the brush
(A) (B)
1. Clean the inner blades using
the short brush by moving it in
direction (A).
Clean the system outer foil,
the shaver body and the
trimmer using the long brush.
Do not move the short brush
in direction (B) as it will
damage the inner blades and
affect their sharpness.
Do not use the short brush to
clean the outer foils.
•
•
Removing the built-in rechargeable battery
Remove the built-in rechargeable battery before disposing of the
shaver. Please make sure that the battery is disposed of at an
officially designated location if there is one.Do not dismantle or
replace the battery so that you can use the shaver again.This
could cause fire or an electric shock. Replace it at an authorized
service center.
Disconnect the power cord
from the shaver when
removing the battery.
Perform steps to 5and lift
the battery, and then remove
it.
•
•
For environmental protection and recycling of materials
This shaver contains a Lithium-ion battery.
Please make sure that the battery is disposed of at an officially
assigned location, if there is one in your country.
ES8113_CH.indb 6 2007/07/11 9:23:57
7
中文
重要事项
使用剃须刀
注意-外刀网很薄，若使用不正确就可能造成损坏。使用剃须
刀前，请确认刀网是否损坏。如果刀网已损坏请不要使用该剃须
刀，因为这样会割伤皮肤。请勿用于修剪宠物的毛发。
给剃须刀充电
除了为本型号专门设计的充电器，不要使用其它任何电源线、充
电器进行充电。将充电器插入非潮湿的家用插座里，拿时双手要
保持干燥。剃须刀在使用和充电过程中可能会变热，但这不是故
障。不要在有阳光直射或其它热源的地方给剃须刀充电。从家用
插座上拔出充电器时要抓住充电器。如果用力拉电源线，可能会
损坏电源线。电源软线不能更换，如果软线损坏，此充电器应废
弃。
充电的合适环境温度为15至35摄氏度。
如液晶显示屏上的指示灯不亮，稍等片刻直至其亮起。
清洁剃须刀
警告-清洁剃须刀前请断开电源线，以防触电。
请在装有两个内刀头的状态进行清洗，若在仅装有一个内刀头的
状态进行清洗，可能会损坏剃须刀。可用水清洗剃须刀，不要使
用盐水或热水。不要将剃须刀长时间浸泡在水中。用蘸肥皂水的
布擦拭剃须刀。不要使用稀释剂，汽油或酒精擦拭剃须刀任何
部位。
存放剃须刀
存放剃须刀时请拔出电源线。不要折弯电源线或将电源线绕在剃
须刀上。请勿将剃须刀放在幼童可以接触到的地方。请妥善保管
本说明书。请妥善处理本产品的包装袋，避免婴幼儿窒息等意外
发生。
规格
型号： ES8113
额定输入： 交流100-240V,150mA
额定输出： 直流5.7V,1.0A
充电时间： 1小时
本产品仅限家庭使用。
本产品符合中国标准GB4706.1附录B和GB4706.9及企业标准
Q/(GZ)PEWWBG6。
各部分名称
保护盖
外刃架
3外刀网
4外刀网释放按钮
5内刀头
6外刃架释放按钮
7指握位置
8刀头浮动选择开关
90/1开关
液晶显示屏
电源线插孔
修剪刀
修剪刀操纵杆
充电器(RE7-40)
充电器电源线
电器插头
旅行包
清洁刷
润滑油
•
ES8113_CH.indb 7 2007/07/11 9:23:57
8
中文
充电中
充电
1
1将充电器电源线插头连接到
剃须刀上。
2
2将充电器插头插入家用电源
插座里。
液晶显示屏上的指示灯亮，充电开始。
液晶显示屏上的指示灯开始闪烁则表示
充电完成。
(最多1小时后)
•
•
交流电剃须
当电池电量低时，您也可以将剃须刀通过充电器连接至家用电源
插座，利用交流电进行剃须。
如果剃须刀不能工作，请充电约1分钟后使用。
•
关于液晶显示屏
液晶显示屏显示电池的剩余电量，从0%至100%，每10%一档。
充电时 充电完成后 充电完成10分钟后
指示灯亮 指示灯每秒闪烁一
次。
指示灯每两秒闪烁一
次。
电池电量不足时
电量显示“10%”后您还可以使用剃须刀1到
2次。
(根据使用情况而定。)
•
显示“10%”， 开始闪烁。
充足电后大约可提供14次剃须所需的电量。
（一次剃须约为3分钟）
•
使用修剪刀
将修剪刀操纵杆往上推，以打开修
剪刀。将修剪刀与皮肤成直角
（90度）的位置向下移动以修剪鬓
角。
ES8113_CH.indb 8 2007/07/11 9:23:57
9
中文
使用剃须刀
剃须
90˚
1
1按下0/1开关。 2
2如上图所示握住剃须刀剃
须。
轻轻地压向面部开始剃须。用另一只手绷紧脸上皮肤，逆着胡
须生长方向前后移动剃须刀。当皮肤适应剃须刀之后您可以稍
稍增加压力。但是施加过多的压力不能为您带来更服贴的剃须
效果。相反，对初次使用者可能会造成皮肤伤害。
•
刀头浮动选择开关
用来选择“SOFT”(柔和)或“LOCK”(锁
定)。
不论剃须刀是否接通或关闭，你都可以改变
刀头浮动模式。
SOFT
LOCK
清洁中
清洁
当液晶显示屏上出现 时，建议
您使用自动清洗·充电装置
或“sonic”（声波）振动清洗模
式来清洗您的剃须刀。
1.断开剃须刀的电源线。
2.在外刀网上涂抹少量洗手液和
水。
3.按下0/1开关2秒钟以上启动声
波洗净模式进行“sonic”（声
波）振动清洗。
显示在液晶显示屏上。
大约20秒钟后，它会自动关
闭，或者按0/1开关关闭它。
4.取下外刀网，按下0/1开关2秒
钟以上启动声波洗净模式进
行“sonic”（声波）振动清
洗。使用流动水来清洁。
5.用干布拭去水珠。
6.取下外刀网和外刃架，使其完
全干燥。
左侧符号表示剃须刀
可以全身水洗。
警告：剃须刀需与电源软线分离
后才能用水清洗。
•
•
ES8113_CH.indb 9 2007/07/11 9:23:58
10
中文
注意声波洗净模式
以声波洗净模式剃须可能会损伤皮肤。关闭剃须刀，再打开即
可取消声波洗净模式。
使用剃须刀时不要将手指放在0/1开关上。这样会导致剃须刀关
闭或进入声波洗净模式。使用剃须刀时将手指放在指握位置
上。
•
•
润滑
为长期保持剃须的舒适度，建议使用随剃须刀一起提供的润滑
油。
1.关闭剃须刀。
2.给每个外刀网涂一滴油。
3.推起修剪刀并涂一滴油。
4.接通剃须刀电源，运转约5秒钟。
5.关闭剃须刀，使用软布从外刀网上拭去多余的润滑油。
更换外刀网和内刀头
建议外刀网每年更换一次，内刀头每两年更换一次，以维持剃须刀
剃须性能。
更换外刀网
1.如图示，按下外刃架释放按钮
并向上提起取出外刃架。
2.如图所示，按下外刀网释放按
钮，拉出外刀网。
3.向内插入外刀网，直至卡到位。
始终以正确的方向安装外刀
网。
安装到剃须刀时，请始终将
外刀网插入到外刃架内。
•
•
2 3
ES8113_CH.indb 10 2007/07/11 9:23:58
Inhaltsverzeichnis
Andere Panasonic Elektrorasierer Handbücher
Panasonic
Panasonic ES-SL41-S Bedienungsanleitung
Panasonic
Panasonic ER-CSF1 Bedienungsanleitung
Panasonic
Panasonic ES8172-A3 Bedienungsanleitung
Panasonic
Panasonic ES-LV97 Bedienungsanleitung
Panasonic
Panasonic ER-2403 Bedienungsanleitung
Panasonic
Panasonic ES?LT20 Bedienungsanleitung
Panasonic
Panasonic ES-8080 Bedienungsanleitung
Panasonic
Panasonic ES2235 Bedienungsanleitung
Panasonic
Panasonic ES-LF51 Bedienungsanleitung
Panasonic
Panasonic ES-LV9QX Bedienungsanleitung
Panasonic
Panasonic ES3831K Bedienungsanleitung
Panasonic
Panasonic ES6510 Bedienungsanleitung
Panasonic
Panasonic ES-LT6A Bedienungsanleitung
Panasonic
Panasonic ES8103S Bedienungsanleitung
Panasonic
Panasonic ES7103K Bedienungsanleitung
Panasonic
Panasonic ES-LV6U Bedienungsanleitung
Panasonic
Panasonic ES-8243 Bedienungsanleitung
Panasonic
Panasonic ER-GK20 Bedienungsanleitung
Panasonic
Panasonic ES-SWLT2 Bedienungsanleitung
Panasonic
Panasonic ES-RW30 Bedienungsanleitung
