Panasonic ET-D75LE95C Bedienungsanleitung

ENGLISH

Fixed-focus Lens 　　　　　　　　　

Operating Instructions

Thank you for purchasing this Panasonic product.

■To ensure correct use of this lens, please read the operating instructions supplied

with the lens and the projector carefully.

■Before using this product, be sure to read “Read this rst!” (Page 3).

■Please save this manual for future use.

Commercial Use

Model No. ET-D75LE95C

DPQX1087ZB

2-ENGLISH

Read this rst! ......................................................................................3

Before Use.............................................................................................4

Attaching the Lens / Detaching the Lens...........................................4

Before replacing the projection lens........................................................ 4

Attaching the Lens...................................................................................5

Detaching the Lens ................................................................................. 6

Projection relationships.......................................................................7

Lens position setup and focus adjustment .......................................9

Lens position setup ................................................................................. 9

Focus Adjustment Function................................................................... 11

Adjustment range by the lens position shift (optical shift)............12

Specications .....................................................................................14

Dimensions .........................................................................................14

Dimensional relationship...................................................... Appendix

█ Contents

ENGLISH-3

Read this rst! Always follow these precautions

WARNING:

Before replacing the projection lens, be sure to turn off the power and

disconnect the power plug from the wall outlet.

zUnexpected projection of light may cause injury to eyes.

zReplacing without removing the power plug may result in electrical shock.

Do not place objects near the light projecting surface.

zThis surface produces intense light. Failure to heed this warning could result in re

or burn injuries.

CAUTION:

Do not use the lens with the protective lm and lens cover left on.

zIf left on, the heat generated during projection could melt them resulting in projector

deformation and damage, and personnel attempting to remove them could suffer

burn injuries.

Do not open the desiccant bag. Do not eat the contents.

Inadvertently ingesting desiccant could be harmful.

zIf the desiccant gets into your eyes or mouth, immediately rinse with plenty of water

and seek medical attention.

zKeep desiccant out of the reach of children.

Note

zThis product cannot be used if an optional frame (ET-PFD510C / ET-PFD310C) is attached

and used with the projector.

4-ENGLISH

Before replacing the projection lens

Return the projection lens to the home position before replacing or removing it.

For details on how to return the lens to the home position, refer to the operating instructions

of the projector.

Attention

zMake sure that the projector power supply is switched off before attaching or detaching the

projection lens.

zAfter removing the projection lens, store it safely away from vibration or impacts.

zBefore attaching the xed-focus lens, remove the protective lm from the light projecting

surface and the lens cover from the lens.

Lens surface Light projecting surface

Lens cover

Protective lm

Attaching the Lens / Detaching the Lens

Before Use

 Supported projectors

PT-SRZ31KC / PT-SRS30KC / PT-SRQ13KC / PT-SRZ12KC / PT-SRS11KC /

PT-SDZ21K2C / PT-SDS20K2C / PT-SDW17K2C / PT-SDZ18K2C / PT-SDZ985C /

PT-SDS955C / PT-SDW935C / PT-SDZ981C

Note

zModels other than the above may also be supported. Refer to the operating instructions of

the projector you are using.

 Supplied Accessories

Make sure that the following has been provided. Numbers enclosed in < > show the

number of accessories.

Lens cover <1>

(The product is delivered with a lens cover attached.)

zBe sure not to touch the light projecting surface or the surface of the lens. Any ngerprints or smudges

on these surfaces will be magnied and lower the quality of the image displayed on the screen.

zThe light projecting surface and lens are made of glass. The lens could be damaged if

brought into contact with or rubbed against hard objects. Handle the lens carefully.

zUse a clean, soft and dry cloth to wipe away any dirt or dust that has adhered to the light

projecting surface or lens. Do not use uffy cloths containing oil, water or dust for cleaning.

zWhen the xed-focus lens is removed from the projector, place it with the light projecting

surface facing upwards.

ENGLISH-5

The illustration for this procedure uses

PT-SDZ21K2C as an example.

Remove the projection lens cover.*1

2) Align the mark on the projection

lens (orange color) with the mark

on the projector (O on the left

side of the LOCK) and insert; then

rotate in a clockwise direction

until it makes a "click" sound.

(i)

(ii)

Projection

lens cover

(i)

(ii)

Orange color

3) Secure the projection lens with

the lens drop prevention screw

included with the projector.

zSecure it in the screw hole (location

shown in the gure to the left) on the right

side of the projection lens mark (orange

color) using a Phillips screwdriver.

4) Attach the projection lens cover.*1

Attention

zGently turn the projection lens

counterclockwise to check that it will not

fall out.

Lens drop

prevention

screw

Attaching the Lens

Attaching the Lens / Detaching the Lens (continued)

*1: Only when using a projector that has a projection lens cover. In addition, there are cases where

the attachment method or removal method of the projection lens cover differs from the procedure

(illustration) described above depending on the model being used. For details, see "Attaching/

removing the projection lens (optional)” in the operating instructions for the projector you are

using.

6-ENGLISH

The illustration for this procedure uses

PT-SDZ21K2C as an example.

1) Remove the projection lens cover.*1

2) Remove the lens drop prevention

screw.

zRemove the rst screw on the right

side of the projection lens mark (orange

color) using a Phillips screwdriver.

3) Turn the projection lens

counterclockwise while holding

down the lens release button to

take it off.

zTurn counterclockwise until the

projection lens mark (orange color) is

aligned with the mark on the projector

(O on left side of the LOCK).

4) Attach the projection lens cover.*1

Attention

zStore the projection lens that was removed

while avoiding vibration and impact.

zStore the lens drop prevention screw that

was removed and do not lose it.

zAttach the supplied lens cover before

storing the lens.

(i)

(ii)

Projection

lens cover

(iii)

(i)

(ii)

Lens

release

button

Orange color

Detaching the Lens

Attaching the Lens / Detaching the Lens (continued)

*1: Only when using a projector that has a projection lens cover. In addition, there are cases where

the attachment method or removal method of the projection lens cover differs from the procedure

(illustration) described above depending on the model being used. For details, see "Attaching/

removing the projection lens (optional)” in the operating instructions for the projector you are

using.

ENGLISH-7

The dimensional relationship between the screen and the projector is shown below.

 Dimensional relationship diagram

Projected image

Screen

Note

zThe indications of this illustration are premised on aligning the projected image size and

position to the full screen.

zThis illustration is not drawn to scale.

SH Projected image height L3 Screen to projector front end

SW Projected image width L4 Screen to projector rear end

SD Diagonal length of the projected image A1 Bottom edge of the screen to the top of

the projector

L1 Projection distance (from screen to

mirror reective surface*) A2 Bottom edge of the screen to the

bottom of the projector

L2 Screen to lens front end

* The mirror reective surface is inside the xed-focus lens, and is not visible from the outside.

Note

zThe illustrations of projectors in this manual are for informational purposes only and do not

represent a specic projector model. Congurations may vary with the model.

zAfter setting the lens position using the function on the projector, the lens position can be

adjusted within the adjustment range described in "Adjustment range by the lens position

shift (optical shift)" (Page 12).

Then dimensions A1 and A2 will change according to lens shift amount.

zDimension L4 is the distance from the projector rear panel to the screen.

zDimension A2 is the distance from the bottom edge of the screen to the bottom of the

adjustable projector legs (with the legs fully screwed in).

Attention

zDimension L4 is not the distance from the projector rear panel to a wall, but the distance

from the projector rear panel to the screen. Provide at least 500 mm (19-11/16") of ventilation

space between the projector rear panel and a wall or other object.

When placing the projector in a conned space, a ventilation and/or air conditioning system

is required. Exhaust heat may accumulate when the ventilation is not sufcient triggering the

protection circuit of the projector.

Projection relationships

8-ENGLISH

 Keystone distortion correction

When attaching this lens for use, regardless of the projector model, set up the projector so that

the projected image is rectangular and the back of the projector and the screen are parallel.

In addition, depending on the projector used, keystone distortion correction may be

feasible after setup.

zWhen using one of

PT-SRZ31KC / PT-SRS30KC / PT-SRQ13KC / PT-SRZ12KC /

PT-SRS11KC / PT-SDZ21K2C / PT-SDS20K2C / PT-SDW17K2C / PT-SDZ18K2C /

PT-SDZ985C / PT-SDS955C / PT-SDZ981C

For keystone distortion in the vertical direction generated within the angle range

below, select [MAIN MENU] →[POSITION] →[GEOMETRY] →[KEYSTONE] →

[VERTICAL KEYSTONE] to perform correction.

Keystone distortion in the vertical direction greater than this angle and keystone

distortion in the horizontal direction can be corrected but the projected image overall

will no longer be in focus.

Correction feasible angle (α): 0 - 5°

zWhen using PT-SDW935C

If keystone distortion in vertical direction or horizontal direction is corrected, the

projected image overall will no longer be in focus. Set up the projector so that the

projected image is rectangular and the back of the projector and the screen are parallel.

zWhen using a projector other than one listed above

Please see "Setting up" in the operating instructions for the projector you are using.

Projection relationships (continued)

 Dimensional relationship

zWhen using one of PT-SRZ31KC / PT-SRS30KC / PT-SRQ13KC / PT-SRZ12KC /

PT-SRS11KC / PT-SDZ21K2C / PT-SDS20K2C / PT-SDW17K2C / PT-SDZ18K2C /

PT-SDZ985C / PT-SDS955C / PT-SDW935C / PT-SDZ981C

For details on projection distance (L1), and A1, A2, L2, L3 and L4 values, refer to

"Projected image size and Projection distance" or "Projection distance formulas" in the

Appendix.

zWhen using a projector other than one listed above

Please see "Setting up" in the operating instructions for the projector you are using.

Screen

(Side view)

ENGLISH-9

Lens position setup

Automatically return the lens to standard position using the projector.

The menu screens shown in these operating instructions are only provided as examples.

Actual menu screens may vary with the specic model.

zWhen using PT-SRZ31KC / PT-SRS30KC / PT-SRQ13KC / PT-SRZ12KC / PT-SRS11KC /

PT-SDZ21K2C / PT-SDS20K2C / PT-SDW17K2C / PT-SDZ18K2C

Lens position setup and focus adjustment

1) Turn on the projector, and start

projection.

2) Press the < 默认 > button on the remote

control while the shift adjustment

screen is displayed.

zThe [HOME POSITION] screen is

displayed.

3) Press ◀▶ to switch the item.

zThe items will switch each time you press

the button.

[NORMAL]

Moves the lens to the home position.

Select this item when replacing or

removing the projection lens. Select

this item when the Fixed-focus Lens

(Model No.: ET-D75LE50C) is used for

projection.

[D75LE95]

[D75LE90]*1

Moves the lens to the ET-D75LE95C

lens standard position.

Select this item when the Fixed-focus

Lens (Model No.: ET-D75LE95C) is

used for projection.

*1: The items displayed will differ depending on the projector

model.

4) Press the < 执行 > button.

z[PROGRESS] is displayed in the [HOME

POSITION] screen, and the lens position

returns to the home position or the lens

standard position.

LENS

HOME POSITION

EXECUTE CANCEL

NORMAL

CHANGE

执行

菜单

Note

zComplete the operation within approximately 5 seconds after the [HOME POSITION]

screen is displayed. The [HOME POSITION] screen will disappear after time limit.

zThe home position of the lens is used when the lens is being replaced or when the

projector is being stored, and it is not the optical center of the screen.

zYou can also display the [HOME POSITION] screen by pressing the < 镜头 > button on the

control panel or the < 移位 > button on the remote control for at least three seconds.

10-ENGLISH

Lens position setup and focus adjustment (continued)

1) Turn on the projector to start the projection.

2) Press the < 菜单 > button to open the [MAIN

MENU] screen. Then select [PROJECTOR

SETUP] and press the < 执行 > button.

3) Select [SERVICE PASSWORD] in the

[PROJECTOR SETUP] menu and press

the < 执行 > button.

4) In the [SERVICE PASSWORD] entry

screen, enter "7590" using the numeric

buttons on the remote control and then

press the < 执行 > button.

zThe [D75LE90 POSITION] screen appears.

5) Press the < 执行 > button in the [D75LE90

POSITION] screen.

z[PROGRESS] is displayed on the [D75LE90

POSITION] screen and lens position moves to the

standard position for the ET-D75LE95C.

Note

zWhen using the PT-SDZ985C / PT-SDS955C /

PT-SDW935C / PT-SDZ981C, the [MAIN VERSION]

of the projector rmware must be the version

described below. Check the [MAIN VERSION] of the

rmware on the [STATUS] screen and upgrade the

rmware version of the projector as needed.*

Projector

Main version

PT-SDZ985C / PT-SDS955C /

PT-SDW935C / PT-SDZ981C 4.04 or higher

[STATUS] screen is displayed by selecting [Main

Menu] →[PROJECTOR SETUP] →[STATUS] or by

pressing the < 状态 > button on the remote control.

菜单

执行

LENS

D75LE90 POSITION

CANCEL

MAIN MENU

PICTURE

POSITION

ADVANCED MENU

DISPLAY LANGUAGE

DISPLAY OPTION

3D SETTINGS

PROJECTOR SETUP

TEST PATTERN

P IN P

4.02

SDZ985C

LAST USED

SW1234567

ET-LAD120

2/2

PROJECTOR SETUP

STARTUP INPUT SELECT

RS-232C

STATUS

SAVE ALL USER DATA

LOAD ALL USER DATA

INITIALIZE

SERVICE PASSWORD

*1: See software download page on website (https://panasonic.net/cns/projector/pass/).

You must be a registered PASS user to use the site described above.

PASS : Panasonic Professional Display and Projector Technical Support Website

Note

zThe lens position set here may not match the intended standard position exactly.

zThe lens position set with this procedure will be used as the standard position. The lens

position can be adjusted within the adjustment range described in "Adjustment range by the

lens position shift (optical shift)" (



Page 12), even after shifting to the standard position.

zDepending on the (OSD) display position on the menu screen, there are cases where the

projected light is obstructed and a part of the menu is not displayed on the screen. In this

case, open [MAIN MENU] →[DISPLAY OPTIONS] →[ON-SCREEN DISPLAY] →[OSD

POSITION] and change settings so that the whole OSD menu can be seen.

zWhen using PT-SDZ985C / PT-SDS955C / PT-SDW935C / PT-SDZ981C

Inhaltsverzeichnis

Andere Panasonic Linse Handbücher

Panasonic

Panasonic ET-DLE105C Bedienungsanleitung

Panasonic

Panasonic VW-W4907 Bedienungsanleitung

Panasonic

Panasonic ET-EMS650 Bedienungsanleitung

Panasonic

Panasonic H-HSA35100PP Bedienungsanleitung

Panasonic

Panasonic Lumix H-ES200 Bedienungsanleitung

Panasonic

Panasonic WV-LZF61/2 Bedienungsanleitung

Panasonic

Panasonic ET-D3LEW60 Bedienungsanleitung

Panasonic

Panasonic ET-D75LE90 Bedienungsanleitung

Panasonic

Panasonic WV-LZ62/8 Bedienungsanleitung

Panasonic

Panasonic AW-S14XBRM Bedienungsanleitung

Panasonic

Panasonic H-RS100400PP Bedienungsanleitung

Panasonic

Panasonic Lumix H-ES12060 Installationsanleitung

Panasonic

Panasonic ET-D3LEF70 Bedienungsanleitung

Panasonic

Panasonic ET-D3QW300 Bedienungsanleitung

Panasonic

Panasonic ET-DLE085C Bedienungsanleitung

Panasonic

Panasonic H-FS14140PP Bedienungsanleitung

Panasonic

Panasonic Lumix H-PS14042 Bedienungsanleitung

Panasonic

Panasonic ET-DLE020C Bedienungsanleitung

Panasonic

Panasonic ET-C1W300 Bedienungsanleitung

Panasonic

Panasonic ET-EMW200 Bedienungsanleitung

Panasonic

Panasonic Lumix H-F007014 Bedienungsanleitung

Panasonic

Panasonic VW-CLT1P Bedienungsanleitung

Panasonic

Panasonic ET-D75LE95 Bedienungsanleitung

Panasonic

Panasonic ET-PLF10 Bedienungsanleitung

Beliebte Linse Handbücher anderer Marken

Navitar

Navitar 1-62314 Leitfaden

Angenieux

Angenieux OPTIMO PRIME Bedienungsanleitung

Sealife

Sealife SL050 Bedienungsanleitung

Navitar

Navitar 1-51200 Leitfaden

MeCan

MeCan NY1S-a5100 Bedienungsanleitung

Tamron

Tamron SP 70-300mm F/4-56 Di VC USD Bedienungsanleitung

FujiFilm

FujiFilm FUJINON ZA17x7.6BERD-S6 Bedienungsanleitung

Navitar

Navitar 1-51332 Leitfaden

Leica

Leica APO-SUMMICRON-SL 1:2/50 ASPH. Bedienungsanleitung

Sony

Sony LKRL-Z200 Series Bedienungsanleitung

Cosina

Cosina Voigtländer SUPER NOKTON 29mm F0.8... Bedienungsanleitung

Arax

Arax PCS ARSAT H(K) 4.5/55 Bedienungsanleitung

Cosina

Cosina Voigtländer NOKTON Bedienungsanleitung

Cosina

Cosina Voigtländer NOKTON Bedienungsanleitung

Navitar

Navitar 1-51338 Leitfaden

Shamir

Shamir Star Einrichtungshandbuch

Canon

Canon J11ex4.5B Bedienungsanleitung

Sony

Sony SAL70200G2 Bedienungsanleitung