Panasonic TH-50PH30E Bedienungsanleitung

Unauthorized copying and distribution is a violation

of law.

Order Number PCZ1104079CE

High Definition Plasma Display

Model No. TH-50PH30E

TH-50PH30ER

GPH14DMON Chassis

TABLE OF CONTENTS

PAGE PAGE

1 Safety Precautions----------------------------------------------- 3

1.1. General Guidelines---------------------------------------- 3

1.2. Touch-Current Check ------------------------------------- 3

2 Warning -------------------------------------------------------------- 4

2.1. Prevention of Electrostatic Discharge (ESD)

to Electrostatically Sensitive (ES) Devices---------- 4

2.2. About lead free solder (PbF)---------------------------- 5

3 Service Navigation ----------------------------------------------- 6

3.1. Service Hint ------------------------------------------------- 6

3.2. Applicable signals ----------------------------------------- 7

4 Specifications ----------------------------------------------------- 9

5 Operating Instructions-----------------------------------------10

6 Service Mode -----------------------------------------------------12

6.1. CAT (Computer Aided Test) mode -------------------12

6.2. IIC mode structure (following items value is

sample data) -----------------------------------------------15

7 Troubleshooting Guide ----------------------------------------16

7.1. Self Check--------------------------------------------------16

7.2. No Power ---------------------------------------------------19

7.3. No Picture-------------------------------------------------- 19

7.4. Local screen failure-------------------------------------- 20

8 Disassembly and Assembly Instructions--------------- 21

8.1. Removal of Rear Cover -------------------------------- 21

8.2. Removal of D-Board------------------------------------- 21

8.3. Removal of HX-Board----------------------------------- 21

8.4. Removal of A-Board------------------------------------- 21

8.5. Removal of Fan------------------------------------------- 22

8.6. Removal of P-Board------------------------------------- 22

8.7. Removal of AC Inlet Assy------------------------------ 22

8.8. Removal of Speaker Terminal Block ---------------- 22

8.9. Removal of SN-Board----------------------------------- 22

8.10. Removal of SS-Board----------------------------------- 23

8.11. Removal of C1-Board ----------------------------------- 23

8.12. Removal of C2-Board ----------------------------------- 24

8.13. Removal of S1-Board ----------------------------------- 24

8.14. Removal of Front Glass, V1, V2-Board and

Cabinet Assy ---------------------------------------------- 24

8.15. Removal of Plasma Display Panel------------------- 26

TH-50PH30E / TH-50PH30ER

9 Measurements and Adjustments -------------------------- 29

9.1. Adjustment------------------------------------------------- 29

9.2. Adjustment------------------------------------------------- 30

10 Block Diagram --------------------------------------------------- 35

10.1. Main Block Diagram ------------------------------------ 35

10.2. Block (1 of 4) Diagram ---------------------------------- 36

10.3. Block (2 of 4) Diagram ---------------------------------- 37

10.4. Block (3 of 4) Diagram ---------------------------------- 38

10.5. Block (4 of 4) Diagram ---------------------------------- 39

11 Wiring Connection Diagram --------------------------------- 40

11.1. Wiring (1) --------------------------------------------------- 40

11.2. Wiring (2) --------------------------------------------------- 41

12 Schematic Diagram--------------------------------------------- 42

13 Printed Circuit Board ------------------------------------------ 42

14 Exploded View and Replacement Parts List ----------- 42

14.1. Exploded View -------------------------------------------- 42

14.2. Electrical Replacement Parts List-------------------- 42

TH-50PH30E / TH-50PH30ER

1 Safety Precautions

1.1. General Guidelines

1. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials.

2. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the

wires have been broken or disconnected, do not attempt to repair or re-wire the units. Replace the entire wiring unit instead.

3. When conducting repairs and servicing, do not twist the Fasten connectors but plug them straight in or unplug them straight

out.

4. When servicing, observe the original lead dress.If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

5. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

6. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

1.2. Touch-Current Check

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground

such as a water pipe, as shown in Figure 1.

3. Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reserve the AC plug in the AC outlet and repeat each of the above measure.

6. The potential at any point (TOUCH CURRENT) expressed as voltage U1and U2, does not exceed the following values:

For a. c.: U1= 35 V (peak) and U2= 0.35 V (peak);

For d. c.: U1= 1.0 V,

Note:

The limit value of U2= 0.35 V (peak) for a. c. and U1= 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and 2.0

mA d. c.

The limit value U1= 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100 kHz.

7. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be

repaired and rechecked before it is returned to the customer.

Figure 1

TH-50PH30E / TH-50PH30ER

2Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi-

tive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-

trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage

caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-

num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-

ble conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the brush-

ing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient

to damage an ES device).

TH-50PH30E / TH-50PH30ER

2.2. About lead free solder (PbF)

Note: Lead is listed as (Pb) in the periodic table of elements.

In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.

The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).

That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.

This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d

suggest the use of Pb free solder as well, although Pb solder may be used.

PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.

Caution

• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher. Please

use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).

• Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).

If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb sol-

der. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.

• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the

opposite side. (see figure below)

Suggested Pb free solder

There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. How-

ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.

TH-50PH30E / TH-50PH30ER

3 Service Navigation

3.1. Service Hint

Board Name Function Board Name Function

A Digital Signal Processor, Microcomputer

Audio Processor, Speaker Out Amplifier

C2 Data drive (Left)

S1 Power switch

D Format Converter, Plasma AI Processor

Sub-Field Processor, Sync Processor

V1 Remote receiver, LED-G, R

V2 Key switch

SN Scan drive, Scan out P Power supply

SS Sustain drive, Sustain out H3 Speaker terminal

C1 Data drive (Right) HX PC / RS-232C_Input terminal

TH-50PH30E / TH-50PH30ER

3.2. Applicable signals

TH-50PH30E / TH-50PH30ER

4 Specifications

Power Source 220 - 240 V AC, 50/60Hz

Power Consumption

Power on 230 W

Stand-by condition 0.5 W

Power off condition 0.3 W

Plasma Display panel Drive method: AC type

50-inch, 16:9 aspect ratio

Screen size 1,105 mm (W) ×622 mm (H) ×1,268 mm (diagonal)

(No. of pixels) 786,432 (1,024 (W) ×768 (H)) [3,072 ×768 dots]

Operating condition

Temperature 0 °C - 40 °C

Humidity 20 % - 80 %

Applicable signals

Colour System NTSC, PAL, PAL60, SECAM, Modified NTSC

Scanning format 525 (480) / 60i 60p, 625 (575) / 50i 50p, 750 (720) / 60p 50p, 1125 (1080) /

60i 60p 50i 50p 24p 25p 30p 24sF

PC signals VGA, SVGA, XGA

SXGA, UXGA ..... (compressed)

Horizontal scanning frequency 15 - 110 kHz

Vertical scanning frequency 48 - 120 Hz

Connection terminals

AV IN

VIDEO BNC 1.0 Vp-p (75-ohm)

AUDIO L-R RCA Pin jack ×2 0.5 Vrms

HDMI TYPE A Connector

COMPONENT / RGB IN

Y / G BNC with sync 1.0 Vp-p (75-ohm)

PB/CB/B BNC 0.7 Vp-p (75-ohm)

PR/CR/R BNC 0.7 Vp-p (75-ohm)

AUDIO L-R RCA Pin jack ×2 0.5 Vrms

DVI-D IN DVI-D 24 Pin Compliance with DVI Revision 1.0

Content Protection Compatible with HDCP 1.1

AUDIO Stereo mini jack (M3) ×1 0.5 Vrms

PC IN High-Density Mini D-sub 15 Pin Y or G with sync 1.0 Vp-p (75-ohm)

Y or G without sync 0.7 Vp-p (75-ohm)

PB/ CB/ B:0.7 Vp-p (75-ohm)

PR/ CR/ R:0.7 Vp-p (75-ohm)

HD / VD:1.0 - 5.0 Vp-p (high impedance)

AUDIO Stereo mini jack (M3) ×1 0.5 Vrms

SERIAL External Control Terminal

D-sub 9 Pin RS-232C compatible

EXT SP Speaker Terminal 6-ohm, 16 W [8 W + 8 W] (10 % THD)

Accessories Supplied

Remote Control Transmitter N2QAYB000535

Batteries R6 (UM3) Size x 2

Dimensions (W ×H ×D) 1,210 mm ×724 mm ×89 mm

Mass (weight)

main unit only approx. 31.0 Kg net

with speakers approx. 36.0 Kg

Notes:

• Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.

• This equipment complies with the EMC standards listed below.

EN55022, EN55024, EN61000-3-2, EN61000-3-3.

TH-50PH30E / TH-50PH30ER

5 Operating Instructions

Andere Handbücher für TH-50PH30E

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Monitor Handbücher

Panasonic

Panasonic TH-42PW7LZ Bedienungsanleitung

Panasonic

Panasonic PanaFlat LC40 TX-D4L31-M Bedienungsanleitung

Panasonic

Panasonic ATH3015W - HDTV MONITOR Bedienungsanleitung

Panasonic

Panasonic PANASYNC PL-70I Bedienungsanleitung

Panasonic

Panasonic TH-42PHW7EX Bedienungsanleitung

Panasonic

Panasonic CT-30WX54 Bedienungsanleitung

Panasonic

Panasonic BT-LH2550 Bedienungsanleitung

Panasonic

Panasonic TH-42PW5 Bedienungsanleitung

Panasonic

Panasonic TH-50PHW7BX Bedienungsanleitung

Panasonic

Panasonic TH-42PF50U Bedienungsanleitung

Panasonic

Panasonic TH-42PH30U Bedienungsanleitung

Panasonic

Panasonic TH42PH20E Bedienungsanleitung

Panasonic

Panasonic BT-3DL2550 Bedienungsanleitung

Panasonic

Panasonic TH-65PF20U Bedienungsanleitung

Panasonic

Panasonic CT34WX53 - 34" TAU TV Bedienungsanleitung

Panasonic

Panasonic CT-32HL42 Bedienungsanleitung

Panasonic

Panasonic TH-42PHD8BK Bedienungsanleitung

Panasonic

Panasonic WVCM143 - COLOR MONITOR Bedienungsanleitung

Panasonic

Panasonic EJ-MDA32E-K Bedienungsanleitung

Panasonic

Panasonic TH-65PF30U Betriebsanleitung

Panasonic

Panasonic CQVD7500U - CAR A/V DVD NAV Bedienungsanleitung

Panasonic

Panasonic TH-55LFV60U Bedienungsanleitung

Panasonic

Panasonic WVCK2020 - COLOR MONITOR Bedienungsanleitung

Panasonic

Panasonic TH-47LFP30W Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

LG M1950D-PZ Bedienungsanleitung