Panasonic PT52DL10 - 52" DLP REAR PJ HDTV Bedienungsanleitung

Projection Television

Operating Instructions

PT-52DL10

Model No.

TQBC0215-1

DLP

ATEXASINSTRUMENTSTECHNOLOGY

COMPATIBLE1080i

720p

SPATIALIZRT

3-DSTEREO

DLP

ATEXAS INSTRUMENTS TECHNOLOGY

COMPATIBLE 1080 i

720p

SPATIALIZRT

3-D STEREO

For assistance, please call : 1-888-VIEW PTV(843-9788)

or send e-mail to : [email protected]

or visit us at www.panasonic.com (USA)

For assistance, please call : 787-750-4300

or visit us at www.panasonic.com (Puerto Rico)

Important Safety Instructions

WARNING: To reduce the risk of electric shock do not remove cover or back. No

user-serviceable parts inside. Refer servicing to qualified service personnel.

The lightning flash with

arrow-head within a triangle

is intended to tell the user

that parts inside the product

are a risk of electric shock to

persons.

The exclamation point within

a triangle is intended to tell

the user that important

operating and servicing

instructions are in the papers

with the appliance.

Note to CATV System Installer: This reminder is provided to direct the CATV system installer’s attention to Article

820–40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point of cable entry as practical.

Important Safety Instructions For Projection TV

1. Read and apply the operating instructions provided with your projection TV.

2. Read all of the instructions given here and retain them for later use.

3. Follow all warnings and instructions marked on the projection TV.

4. Unplug this projection TV from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth

for cleaning.

Do not use attachments / accessories not recommended by the projection TV manufacturer as they may cause hazards.

6. Do not use this projection TV near water. For example: Avoid placing it near a bathtub, washbowl, kitchen sink, or

laundry tub, in a wet basement, or near a swimming pool, etc.

7. Do not place this projection TV on an unstable cart, stand or table. The projection TV may fall, causing serious injury to

a child or adult, and serious damage to the appliance. Use only with a cart or stand recommended

by the manufacturer, or sold with the projection TV.

7A. An appliance and cart combination shall be moved with care. Quick stops, excessive force, and

uneven surfaces may cause the appliance and cart combination to overturn.

8. Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to insure reliable operation

of the projection TV and to protect it from overheating. These openings must not be blocked or covered. There shall be

at least 10 cm of space from these openings. The openings shall never be blocked by placing the projection TV on a

bed, sofa, rug or other similar surface. This projection TV shall never be placed near or over a radiator or heat register.

This projection TV shall not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.

9. Operate only from the type of power source indicated on the marking label. If you are not sure of the type of power

supplied to your home consult your television

dealer or local power company.

10. This projection TV is equipped with a polarized

alternating-current line plug (a plug having one

blade wider than the other). This plug will fit into

the power outlet only one way. This is a safety

feature. If you are unable to insert the plug fully

into the outlet, try reversing the plug. If the plug

should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the

safety purpose of the polarized plug.

11. Do not allow anything to rest and to pinch on the

power cord. Do not locate this projection TV

where the cord will be abused by persons

walking on it.

EXAMPLE OF ANTENNA GROUNDING AS

PER (NEC) NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

LEAD-IN WIRE

GROUND

CLAMP

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The pictorial representation

of a hot surface within a

triangle is intended to tell the

user that parts inside the

product are a risk of burns

to persons.

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-20)

12. Do not overload wall outlets and extension cords as this can result in fire or electric shock.

13. Never push objects of any kind into this projection TV through cabinet slots as they may touch dangerous voltage

points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projection TV.

14. If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to

provide some protection against voltage surges and built up static charges. In the U.S.Selection 810 of the National

Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit,

connection to grounding electrodes, and requirements for the grounding electrode. See Figure.

15. For added protection for this projection TV during a lightning storm, or when it is left unattended and unused for long

periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the receiver due

to lightning and power-line surges.

16. An outside antenna system shall not be located in the vicinity of overhead power lines or other electric light or power

circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system extreme care

shall be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Unplug this projection TV from the wall outlet, and refer servicing to qualified service personnel under the following

conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the projection TV.

c. If the projection TV has been exposed to rain or water.

d. If the projection TV does not operate normally by follow the operating instructions. Adjust only those controls that are

covered by the operating instructions as improper adjustment of other controls may result in damage and will often

require extensive work by a qualified technician to restore the projection TV to normal operation.

e. If the projection TV has been dropped or the cabinet has been damaged.

f. When the projection TV exhibits a distinct change in performance - this indicates a need for service.

18. Do not attempt to service this projection TV yourself as opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified service personnel.

19. When replacement parts are required, be sure the service technician has used replacement parts specified by the

manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire,

electric shock, or other hazards.

20. Upon completion of any service or repairs to this projection TV, ask the service technician to perform routine safety

checks to determine that the projection TV is in safe operating condition.

21. WARNING: To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

22. WARNING: Because the temperature of the lamp unit is elevated immediately after its use, a direct touch to it may

cause burns. After the lamp has cooled enough, replace the lamp unit.

23. CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH A RECEPTACLE OR

OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

24. CAUTION: This TV set for use only with TV-stand (Model: TY-S52DL10)

Use with other stand is capable of resulting in instability causing possible injury.

NOTE: This equipment is designed to operate in the U.S.A..

Important Safety Instructions

Dear Panasonic Customer

Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment

from your new projection television set.

To obtain maximum benefit from your set, please read these Instructions before making any adjustments,

and retain them for future reference.

Retain your purchase receipt also, and note down serial number of your set in the space provided on

the rear cover of these instructions.

Visit our Panasonic Web Site for USA : www.panasonic.com

FCC STATEMENT:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio / TV technician for help.

FCC CAUTION:

To assure continued compliance and prevent undesirable interference, use only the provided shielded VGA cable with 2 ferrite cores

(Part# TSXF147) while connecting the Projection TV to a computer. Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

Pursuant to 47CFR, Part 15.21 of the FCC rules, any changes or modifications to this projection TV not expressly approved by

Matsushita Electric Corporation of America could cause harmful interference and would void the user’s authority to operate

this device.

Responsible Party:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For assistance, please call : 1-888-VIEW PTV(843-9788)

or send e-mail to : [email protected]

or visit us at www.panasonic.com (USA)

For assistance, please call : 787-750-4300

or visit us at www.panasonic.com (Puerto Rico)

FCC Declaration of Conformity

PT-52DL10

Matsushita Electric Corporation of America

One Panasonic Way Secaucus, NJ 07094

1-800-528-8601

Trademarks

•DLP are registered trademark of Texas Instruments.

•Certain audio features of this product are manufactured under a license from Desper Products, Inc. Spatializer® and the circle-in-

square device are trademarks owned by Desper Products, Inc.

•VGA is a trademark of International Business Machines Corporation.

•Macintosh is a registered trademark of Apple Computer, USA.

•S-VGA is a registered trademark of the Video Electronics Standard Association.

Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.

Table of Contents

Important Safety Instructions ................................ 2

Installation ............................................................... 6

Receiver Location .................................................. 6

Optional External Equipment ................................. 6

AC Power Supply Cord .......................................... 6

Safety Precaution................................................... 6

Remote Control Battery Installation ....................... 7

Connecting the Antenna Cable to the RF In Termina

l .... 8

Antenna / Cable Connection .................................. 8

How to connect the “1, 2, 3, 4” Input Terminals ..... 11

How to connect the COMPONENT VIDEO Input Terminals ......

How to connect the AV Prog. Out Terminals .......... 13

How to connect the PC Input Terminals ................. 14

Analog RGB signals that can be input ................... 15

Location of Controls ............................................... 16

Illuminated Remote Control ................................... 16

Controls and Terminals on the projection TV ......... 18

Power ON / OFF ....................................................... 20

Connecting the Plug to the Wall Outlet .................. 20

Turning the Power ON and OFF ............................ 20

Flow Chart of Main menu ....................................... 22

Tuning channels (Automatic channel programming) .......

Tuning channels (Manual channel programming) ...........

ASPECT Controls .................................................... 28

VHF, UHF and CATV ................................................ 30

Cable TV ................................................................... 31

Searching for the desired channel (Channel search) ....

Playing a VCR or other peripheral equipment ..... 33

Playing games in game mode................................ 34

Recall / Mute ............................................................ 35

Split screen .............................................................. 36

Adjusting screen position and size ....................... 38

Audio Adjustments ................................................. 40

Picture Adjustments ............................................... 42

Playing special video software .............................. 45

Closed Captions ...................................................... 46

Lock Feature ............................................................ 48

Customizing the VIDEO INPUT labels ................... 51

Selecting STEREO / SAP / MONO .......................... 53

Using the off-timer .................................................. 54

Video game player to VIDEO INPUT ...................... 55

Optimizing display for DVC recording mode

(DVC PLAYBACK MODE) ..................................... 56

Turning OFF digital comb filter .............................. 57

Automatically changing screen size

for VIDEO INPUT modes...................................... 58

Setting when 480p signals (sequential scan) are

input through COMPONENT VIDEO INPUT ....... 59

CLOCK ..................................................................... 60

Switching languages for display ........................... 61

Replacing the lamp unit ......................................... 62

Operating peripheral equipment using

the remote control ............................................... 63

Troubleshooting ...................................................... 71

Cleaning ................................................................... 72

Specifications .......................................................... 73

The Video / Audio connection between components can be made with shielded video and audio cables. For best

performance, video cables should utilize 75 Ωcoaxial shielded cables. Cables are available from your dealer or electronic

supply house.

Before you purchase any cables, be sure you know what type of output and input connectors your various components

require. Also determine the length of cable you’ll need.

Installation

Receiver Location

This unit is intended to be used with an optional stand or entertainment center. Consult your dealer for available options.

Locate for comfortable viewing. Avoid placing where sunlight or other bright light (including reflections) will fall on the

screen.

Use of some types of fluorescent lighting can reduce remote control transmitter range.

Adequate ventilation is essential to prevent internal component failure. Keep away from areas of excessive heat or

moisture.

Optional External Equipment

AC Power Supply Cord

CAUTION: To prevent electric shock, match wide blade of plug to wide slot of AC outlet and fully insert. Do not use this

(polarized) plug with a receptacle or other outlet unless the blade can be fully inserted to prevent blade

exposure.

Please take safety precautions to prevent the unit

from falling over.

The unit may fall over during earthquakes, or if

someone stands on or shakes the projection TV.

Safety Precaution

Fixing to a wall

Use a strong rope or a chain (not included)

to fasten the projection TV firmly to a strong

support such as a wall or pillar.

Remote Control Battery Installation

Helpful Hint:

For frequent remote control users, replace old

batteries with Alkaline batteries for longer life.

Note: In order to maximize the life of the batteries, the

lighted buttons on the Remote Control can be turned OFF

and ON by pressing R-TUNE and RECALL at the same

time.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.

Observe the following precautions:

1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.

2. Do not combine a used battery with a new one.

3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

5. Battery replacement is necessary when the remote control acts sporadically or stops operating the projection TV set.

Helpful Hint:

Whenever you remove the batteries, you may

need to reset the remote control infrared

codes. We recommend that you record the code

on page 64, prior to setting up the remote.

Requires two AA batteries (supplied).

1. Turn the Transmitter face down.

Remove top cover by pressing

down on marking and sliding cover

off in the direction indicated.

2. Install the batteries as shown in

the battery compartment. (Polarity

+ or – must match the markings in

the compartment).

3. Replace the cover and slide in

reverse until the lock snaps.

Installation

Two AA size

Antenna / Cable Connection

Incoming Cable From Home Antenna (75 Ω)

VHF / UHF

on Back of Set

Cable Connection - For reception of cable channels (01 - 125) connect the cable supplied by your local cable company.

Antenna Mode must be set to CABLE. (Refer to Antenna Mode section.)

Incoming 75 ΩCable (From Cable Company)

VHF / UHF

on Back of Set

Note:

Certain cable systems offset some channels to reduce interference or have Premium (scrambled) channels. A cable

converter box is required for proper reception. Check with your local Cable company for its compatibility requirements.

Connecting the Antenna Cable to the RF In Terminal

AUDIO

AMP

AUDIO

VIDEO

S-VIDEO

AUDIO

VIDEO

INPUT

ANT1 ANT2

SPLIT

OUT

COMPONENT VIDEO INPUT

PROG

OUT

213

ANT1 ANT2

SPLIT

OUT

UHF Antenna

RF In Terminal

VHF Antenna

Mixer

Coaxial Antenna Plug

Cable Box

Antenna Connection - For proper reception of VHF / UHF channels, an external antenna is required. For best reception

an outdoor antenna is recommended. Antenna Mode must be set to projection TV.

Installation

75 Ω

Coaxial Cable

Antenna Connection (Cable Box, no VCR)

Use this configuration when connecting the projection TV to a cable TV system using a Cable Box.

Connect the cable from the antenna

or cable system to the ANT1

terminal on the back of the

projection TV.

Incoming Cable from Antenna

or Cable TV System

AUDIO

AMP

AUDIO

VIDEO

S-VIDEO

AUDIO

VIDEO

INPUT

ANT1 ANT2

SPLIT

OUT

COMPONENT VIDEO INPUT

PROG

OUT

213

ANT1 ANT2

SPLIT

OUT

Installation

ANTENNA TERMINALS

ON THE BACK OF THE

PROJECTION TV CABLE BOX

INPUTOUTPUT

TERMINAL ON

THE BACK OF

THE CABLE BOX

Notes:

•When the antenna cable is connected to the projection TV antenna terminal via a cable box or VCR, set the TV channel

to CH3 or CH4 cable, after select ANT2 in the PROGRAM CHANNELS. (See page 24, 26) This does not apply when

signal is input from VIDEO INPUT.

•To use special features such as Favorite Channel Captions, ANT1 must be selected in the PROGRAM CHANNELS.

(See page 24, 26)

Antenna Connection (Cable Box, and VCR)

Use this configuration when connecting the projection TV to a cable TV system using a Cable Box and VCR.

Connect the cable from the antenna

or cable system to the ANT1

terminal on the back of the

projection TV.

Connect the cable from the

Output terminal on the back

of the Cable Box to the

Antenna input terminal on the

back of the VCR.

CABLE BOX

Incoming Cable from Antenna

or Cable TV System

TO VCR

Connect the cable from the

antenna or cable system to

the Input terminal on the

back of the CABLE BOX.

OUTPUT

S-VIDEO VIDEO L-AUDIO-R

AUDIO

AMP

AUDIO

VIDEO

S-VIDEO

AUDIO

VIDEO

INPUT

ANT1 ANT2

SPLIT

OUT

COMPONENT VIDEO INPUT

PROG

OUT

213

ANT1 ANT2

SPLIT

OUT

Installation

INPUT OUTPUT

OUTPUT INPUT

VCR

Notes:

•When the antenna cable is connected to the projection TV antenna terminal via a cable box or VCR, set the TV channel

to CH3 or CH4 cable, after select ANT2 in the PROGRAM CHANNELS. (See page 24, 26) This does not apply when

signal is input from VIDEO INPUT.

•To use special features such as Favorite Channel Captions, ANT1 must be selected in the PROGRAM CHANNELS.

(See page 24, 26)

ANTENNA TERMINALS

ON THE BACK OF THE

PROJECTION TV

TERMINAL ON

THE BACK OF

THE CABLE BOX

Andere Handbücher für PT52DL10 - 52" DLP REAR PJ HDTV

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Projektionsfernsehen Handbücher

Panasonic

Panasonic PT-51G46C Bedienungsanleitung

Panasonic

Panasonic TX-47P600HZ Bedienungsanleitung

Panasonic

Panasonic PT-51HX43 Bedienungsanleitung

Panasonic

Panasonic TX-47P600H Bedienungsanleitung

Panasonic

Panasonic PT56WXF90 - DIGITAL PTV MONITOR Bedienungsanleitung

Panasonic

Panasonic TX-51P100 series Bedienungsanleitung

Panasonic

Panasonic PT-56WXF95 Bedienungsanleitung

Panasonic

Panasonic TX-47P600X Bedienungsanleitung

Panasonic

Panasonic TX-47P600HM Bedienungsanleitung

Panasonic

Panasonic TX-43P250 Bedienungsanleitung

Panasonic

Panasonic PT-4743 Bedienungsanleitung

Panasonic

Panasonic PT50DL54 - 50" DLP TV Bedienungsanleitung

Panasonic

Panasonic PT56WXF90W - DIGITAL PTV MONITOR Bedienungsanleitung

Panasonic

Panasonic TC-51P250 Series Bedienungsanleitung

Panasonic

Panasonic PT-51G35 Bedienungsanleitung

Panasonic

Panasonic TX-51P800X Bedienungsanleitung

Panasonic

Panasonic TC-43P250H Bedienungsanleitung

Panasonic

Panasonic TX-47WG25 Series Bedienungsanleitung

Panasonic

Panasonic PT 52LCX66 Bedienungsanleitung

Panasonic

Panasonic PT53TWD64 - 53" PROJECTION TV Bedienungsanleitung

Panasonic

Panasonic TX-47P500H Bedienungsanleitung

Panasonic

Panasonic PT-52LCX15K Bedienungsanleitung

Panasonic

Panasonic PT-52LCX35-B Operating Bedienungsanleitung

Panasonic

Panasonic TX-56P800H Bedienungsanleitung

Beliebte Projektionsfernsehen Handbücher anderer Marken

Samsung

Samsung ST-43T6P Bedienungsanleitung

Toshiba

Toshiba ColorStream TP50G60 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric WD-65734 Bedienungsanleitung

Optoma

Optoma EP652A Bedienungsanleitung

Samsung

Samsung SP43T8HPX/XEC Bedienungsanleitung

Philips

Philips 28PW6006 - annexe 1 Bedienungsanleitung

Sony

Sony KP-57WS500 - 57" Hi-scan 1080i™ 16:9 Projection... Benutzerhandbuch

Philips

Philips 43PP8421 Bedienungsanleitung

Hitachi

Hitachi 51F510 Bedienungsanleitung

RCA

RCA P52950 Bedienungsanleitung

Sony

Sony KP-51DS1U Bedienungsanleitung

Magnavox

Magnavox 51MP392H - 51" Widescreen Hd Ready Tv Bedienungsanleitung

Hitachi

Hitachi 46F510 Bedienungsanleitung

Pioneer

Pioneer Elite PRO 510HD Bedienungsanleitung

Philips

Philips 43PP8421 Handbuch

JVC

JVC I'Art Pro AV-48P776 Bedienungsanleitung

Sony

Sony GRAND WEGA KDF-55XS955 Bedienungsanleitung

Sony

Sony KP-46WT520 - Wide Screen Projection Tv Bedienungsanleitung