Panasonic ET-PKV400B Bedienungsanleitung
ENGLISH
Installation Instructions
Projector Mount Bracket
* The gure above shows a combination of this product and the separately sold ceiling mount bracket (for low
ceilings) ET-PKL100S.
Thank you for purchasing this Panasonic Product.
JTo customers
The “Installation Instructions” is intended for use by installation personnel. Be sure to employ certied
personnel to perform the installation. After installation, have the installation personnel return these “Installation
Instructions” to you, and save it for future use. When moving or removing the projector, give this “Installation
Instructions” to the installation personnel and have them perform the procedure.
JTo installation personnel
Carefully read the “Installation Instructions” and install this product correctly and safely.
Be sure to read through the section entitled “Read this rst!” (page 3) before proceeding with the installation.
After installation, return these “Installation Instructions” to the customer.
TQZJ615-4
Model No.
ET-PKV400B
2 - ENGLISH
Contents
Read this rst! ................................................................................................... 3
Product description........................................................................................... 4
Installation position........................................................................................... 5
Installation.......................................................................................................... 7
Setting up the screen .......................................................................................................... 7
Screws tightening torques .................................................................................................. 7
Attaching the projector drop-prevention kit ......................................................................... 7
Installing the bracket to the projector .................................................................................. 8
Specications .................................................................................................. 10
Dimensional relationship ...................................................................Appendix
ENGLISH - 3
Read this rst! Always follow these precautions
CAUTION:
Only install a designated projector.
Only install using a designated method.
zThe projector may fall down and be damaged, and an injury may result.
Do not install the unit in a location that may impede projector ventilation.
zA re may result.
Do not hang from or hang objects on the projector or ceiling mount bracket.
zThe projector may fall and cause injury.
When installing, always use the supplied components.
zThe unit may be damaged, or the projector may fall down and an injury may result.
Install the mounting screws and power cable in such a way that they will not make contact with metal
objects inside the ceiling.
zElectric shocks may result from contact with any metal objects inside the ceiling.
rPanasonic takes no responsibility for any accident or damage caused by the installation of the
ceiling mount bracket using methods that are not described or methods that do not use the parts
specied in these Installation Instructions.
rIf products are no longer being used, they should be dismantled and removed by certied personnel
as soon as possible.
WARNING:
Installation work should only be carried out by the certied personnel.
zIf this product is not installed correctly, serious accidents may result.
zFollow the instructions specied in “Installation” of this manual, and perform secure installation.
Install the ceiling mount bracket in accordance with the structure and materials of the installation
location.
zIf a mistake is made in the installation procedure, the ceiling mount bracket may fall down and an injury may
result.
Mounting and installation must be carried out by two or more persons.
zWhen installing the projector in an overhead location, for example, in a high ceiling, at least two persons will
be required to handle the installation.
Make sure that your footing is safe and secure during installation.
zIf your footing is not secure, you may fall down or drop the unit, and an injury may result.
Do not loosen or remove the ceiling mount bracket screws or bolts unnecessarily.
zThe projector may fall down and an injury may result.
Do not install in a location that is not strong enough.
zIf the installation location is not strong enough, the unit may fall down and damage to the projector or an
injury may result.
Do not install the ceiling mount bracket in humid or dusty locations or in locations where the ceiling
mount bracket may come into contact with oily smoke or steam.
zUsing the projector under such conditions may result in re or electric shock. Also, the oil will cause the
plastic to deteriorate and the projector may fall down when installed on a ceiling.
Do not allow children to reach the supplied screws and at washer.
zThe supplied screws and metal ttings can cause personal injury if swallowed.
zIf swallowed, seek medical advice immediately.
Do not disassemble or modify the ceiling mount bracket.
zThe projector may be damaged or fall, causing injury.
4 - ENGLISH
Product description
This is a projector mount bracket for installing projectors.
■Applicable ceiling mount brackets
ET-PKL100S (for low ceilings) / ET-PKL100H (for high ceilings)
Note
zIn this document, the alphabet letters at the end of the projector part numbers are omitted.
■Structural components
Parts name Form (number of parts) Applications
Projector mount
bracket × 1
This is used to install the projector
itself.
It has a function which allows
adjustment of the left and right tilt.
Screws
Screw, captive washer (M4×10)
These are used to secure the
brackets to the projector.
× 4
Projector drop-
prevention kit
Screw, captive washer (M4×12)
Prevents the projector from falling.
× 1
Wire rope
[2.0 mm (3/32") wire diameter, 600 mm (23-5/8") length]
× 1 × 1
Wire rope for projector Screw, captive
washer (M4×12)
Flat washe
r
(M8)
[2.0 mm (1/8") wire diameter,
600 mm (1´11) length]
× 1
× 1
Flat washer
× 1
zStore small parts in an appropriate manner, and keep them away from children.
zTightening torque for the screw is M4: 1.25 ± 0.2 N•m.
zWhen tightening up the screws, use a tool such as a torque screwdriver. Do not use electric screwdrivers or
impact screwdrivers.
Attention
zDispose of the packaging materials properly after taking the product out of it.
Note
zThe projector models listed below require three of the four supplied captive washer screws (M4 × 10) for
installation.
Model: PT-VW355N, PT-VW350, PT-VX425N, PT-VX420, PT-VX421; PT-VW360, PT-VX430, PT-VX431K
ENGLISH - 5
Installation position
The dimensional relationship between the screen and projector is shown below.
Establish the ceiling installation position after accessing the dimensional relationship diagram and the Dimension-
al relationship.
The projection distance can be adjusted using the zoom lens. Check the projection screen while making ne ad-
justments.
The projection vertical position can be adjusted by vertical lens shift function of the projector with the lens shift
function. Then “H” will change according to lens shift amount.
■Dimensional relationship diagram
(When using the ceiling mount bracket ET-PKL100S (for low ceilings))
SW SH
H
L(LW/LT)
Ceiling
Screen
142
(5-19/32")
H1*
SD
SH
SW
Projected image
<Units: mm (")>
132
(5-3/16")
25(31/32")
L1F L1R
W1
* The thickness of
the attachment
plate is included.
(When using the ceiling mount bracket ET-PKL100H (for high ceilings))
H2 *
L(LW/LT)
142
(5-19/32")
SD
SH
SW
132
(5-3/16")
Ceiling
Screen
Projected image
<Units: mm (")>
L2F L2R
W2
(20 mm (25/32") increment)
SW SH
H
* The thickness of
the attachment
plate is included.
6 - ENGLISH
Note
zThis illustration assumes that the projector will be installed so that the projected image lls the screen and
properly aligned with it.
zThis drawing is not in exact scale.
SH Height of the projection
area HDistance from the center of lens to the image upper end
SW Width of the projection
area H1 / H2 Distance from the center of lens to the attachment plate (including
plate thickness)
SD Diagonal length of the
projection area L1F / L2F Distance from the center of attachment plate to the front end of lens
L(LW/LT)*1Projection distance L1R / L2R Distance from the center of attachment plate to the rear end of
projector
W1 / W2 Distance from the center of attachment plate to the center of lens
*1: LW : Minimum distance; LT : Maximum distance
Note
zDepending on the product, the appearance may differ from the illustrations in these installation instructions.
Attention
zInstall the projector at least 500 mm (19-11/16") on the air intake ports (1,000 mm (39-3/8") on the exhaust port
side) away from the surrounding walls or objects in order to ensure that the air intake/exhaust ports of the pro-
jector will not be blocked.
zAvoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner or
lighting equipment (studio lamps, etc.).
■Dimensional relationship
For the formula of the projection distance (L) and the other specications (H, H1 / H2, L1F/L2F, L1R / L2R, W1 /
W2), refer to the appendix at the end of this instruction.
Installation position (continued)
ENGLISH - 7
Installation
After checking the height, width and structure of the installation location while referring to the “Dimensional
relationship diagram” (pages 5-6) and “Dimensional relationship” in the Appendix, determine the appropriate posi-
tions for setting up the screen and installing the projector.
Setting up the screen
Set up the screen according to the specied method in a position which takes into account the projection distance
and angle and the type of screen being used.
Screws tightening torques
M4………1.25 ± 0.2 N • m
zWhen tightening the screws, use a torque screwdriver or a hexagonal torque wrench to tighten the screws to
the specied tightening torques. Do not use electric screwdrivers or impact screwdrivers.
Attaching the projector drop-prevention kit
Install the wire rope to the projector (sold separately).
<
For PT-VZ585N, PT-VZ575N, PT-VZ580, PT-VZ570, PT-VW545N, PT-VW535N, PT-VW540, PT-VW530, PT-VX615N,
PT-VX605N, PT-VX610, PT-VX600, PT-VX61K, PT-VX60, PT-VX51K, PT-VX50, PT-VMZ60, PT-VMZ50, PT-VMZ40,
PT-VMW60, PT-VMW50, PT-VMZ601K, PT-VMZ501K, PT-VMZ401K, PT-VMW601K, PT-VMW501K / PT-VGZ601K>
Adjustable
feet lock latch
Adjustable feet The illustration is an example when it is attached to
PT-VZ585N.
1 Place the projector upside down on top of a soft
cloth.
2 Retract the adjustable feet.
zPress the adjustable feet lock latch and release
them at shortest length of the adjustable feet.
Or rotate the adjustable feet in clockwise to
retract them.
A
A
Wire rope
Wire rope Screw, captive
washer
(M4 x 12)
Screw, captive
washer 3 As illustrated on the left, secure the one end
(round crimping terminal) of the supplied wire
rope to the A on the projector by using the sup-
plied captive washer screw (M4 x 12).
Attention
zBe sure to use the supplied wire rope.
Note
zUse the supplied at washer while installing the
wire rope to the ceiling.
zThe position of A may vary with the model. Check
the position and number of the screw hole in “Ceiling
mount hole size” indicated on the bottom of the
projector, try placing the bracket on the projector
bottom, and use the screw hole unoccupied.
8 - ENGLISH
Installation (continued)
<For PT-VW355N, PT-VW350, PT-VX425N, PT-VX420, PT-VX421; PT-VW360, PT-VX430, PT-VX431K>
A
A
Wire rope
Wire
rope
Screw, captive
washer
(M4 x 12)
Screw, captive
washer Note
zFor the position of A of the PT-VW355N,
PT-VW350, PT-VX425N, PT-VX420, PT-VX421;
PT-VW360, PT-VX430, PT-VX431K models, refer
to the image on the left.
<For PT-LRZ35, PT-LRZ35U, PT-LRW35, PT-LRW35U>
A
A
Wire rope
Wire
rope
Screw, captive
washer
(M4 x 12)
Screw, captive
washer
Note
zFor the position of A of the PT-LRZ35, PT-LRZ35U,
PT-LRW35, PT-LRW35U models, refer to the image
on the left.
Installing the bracket to the projector
Install the bracket to the projector (sold separately) by following the procedure below.
<
For PT-VZ585N, PT-VZ575N, PT-VZ580, PT-VZ570, PT-VW545N, PT-VW535N, PT-VW540, PT-VW530, PT-VX615N,
PT-VX605N, PT-VX610, PT-VX600, PT-VX61K, PT-VX60, PT-VX51K, PT-VX50, PT-VMZ60, PT-VMZ50, PT-VMZ40,
PT-VMW60, PT-VMW50, PT-VMZ601K, PT-VMZ501K, PT-VMZ401K, PT-VMW601K, PT-VMW501K / PT-VGZ601K>
Projector
mount
bracket
Captive washer
screws (M4 × 10)
Wire rope
The illustration is an example when it is attached to
PT-VZ585N.
1 Pass the wire rope through the hole of the projector
mount bracket as illustrated on the left.
2 Secure the projector mount bracket to the bottom of
the projector using the 4 supplied captive washer
screws (M4 × 10) as illustrated on the left.
Wire rope
ENGLISH - 9
Installation (continued)
<For PT-VW355N, PT-VW350, PT-VX425N, PT-VX420, PT-VX421; PT-VW360, PT-VX430, PT-VX431K>
Projector
mount
bracket
Captive washer
screws (M4 × 10)
Wire rope
Screw
position
1 Secure the projector mount bracket to the bottom of
the projector using three supplied captive washer
screws (M4 × 10) as illustrated on the left.
zUse three of the four captive washer screws sup-
plied with this product.
<For PT-LRZ35, PT-LRZ35U, PT-LRW35, PT-LRW35U>
Projector
mount
bracket
Captive washer
screws (M4 × 10)
Wire rope
Screw
position
1 Pass the wire rope through the hole of the projector
mount bracket as illustrated on the left.
2 Secure the projector mount bracket to the bottom of
the projector using the 4 supplied captive washer
screws (M4 × 10) as illustrated on the left.
Wire rope
Attention
zFor information on how to join this product to the ceiling mount bracket (for low ceilings) (separately sold) or the
ceiling mount bracket (for high ceilings) (separately sold) and how to attach the wire rope in the ceiling, refer to
the installation instructions or other instructions supplied with the ceiling mount bracket (for low ceilings) or the
ceiling mount bracket (for high ceilings).
Screw
position
Specications
Range of
adjustment
Horizontal tilt
correction angle*1 ± 10°
External dimensions
Width: 312.5 mm (12-7/32")
Height: 62.0 mm (2-7/16")
Depth: 248.5 mm (9-25/32")
Weight Approx. 0.96 kg (2.12 lbs)
*1 When using the ceiling mount bracket ET-PKL100S (for low ceilings) or the ceiling mount bracket
ET- PKL100H (for high ceilings).
Web Site : https://panasonic.net/cns/projector/
© Panasonic Corporation 2014
Panasonic Corporation
SS0714JZ4070 -PT
Inhaltsverzeichnis
Andere Panasonic Rack & Stand Handbücher
Panasonic
Panasonic WV-Q150CE Bedienungsanleitung
Panasonic
Panasonic TY27G22M - TV STAND Bedienungsanleitung
Panasonic
Panasonic TY-ST42P50 Bedienungsanleitung
Panasonic
Panasonic TY-S37PA50W Bedienungsanleitung
Panasonic
Panasonic PPMF12D Bedienungsanleitung
Panasonic
Panasonic TY-ST10-M Bedienungsanleitung
Panasonic
Panasonic PAW-GRDSTD40 Bedienungsanleitung
Panasonic
Panasonic TY-ST20-K Bedienungsanleitung
Panasonic
Panasonic TY-ST75PE9 Bedienungsanleitung
Panasonic
Panasonic ET-JPC200BK Bedienungsanleitung
Panasonic
Panasonic TY32G22M - TV STAND Bedienungsanleitung
Panasonic
Panasonic WV-Q52A Bedienungsanleitung
Panasonic
Panasonic TY-ST85P12 Bedienungsanleitung
Panasonic
Panasonic ET-PFD510 Bedienungsanleitung
Panasonic
Panasonic TY-35G30M Bedienungsanleitung
Panasonic
Panasonic i-PRO WV-Q121B Bedienungsanleitung
Panasonic
Panasonic TY-ST42D1-WG Bedienungsanleitung
Panasonic
Panasonic CA-FN50N Bedienungsanleitung
Panasonic
Panasonic NN-TK816CSCP Bedienungsanleitung
Panasonic
Panasonic TY-ST103PF9 Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
