Panasonic WV-Q151CE Bedienungsanleitung

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

The model number is abbreviated in some descriptions in this manual.

Ceiling Mount Bracket

Operating Instructions

Model No. WV-Q151C

WV-Q151CE

WV-Q151S

WV-Q151SE

CONTENTS

Preface ....................................................................................................................................... 2

Precautions ................................................................................................................................ 2

Major Operating Controls and Their Functions .......................................................................... 4

Installations ................................................................................................................................ 5

Specifications ................................................................................................................ back cover

Standard Accessories ................................................................................................... back cover

Precautions

• Refer installation work to the dealer.

Installation work requires technique and experiences. Failure to observe this may cause

fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.

• Avoid installing this bracket in the locations where salt damage occurs or corrosive

gas is produced.

Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera

may occur.

• Use only the specified camera.

Failure to observe this may cause a fall of an inappropriate camera resulting in injury or

accidents. Mount WV-NS202 on this bracket exclusively.

• The screws and fixation mechanisms shall be tightened securely.

Failure to observe this may cause a fall of the camera resulting in injury.

• The measures of protection against a fall of the camera shall be taken.

Failure to observe this may cause injury. Be sure to install the safety wire.

Preface

This ceiling mount bracket is exclusively designed to mount the network camera, WV-NS202,

on a ceiling.

This bracket can be used for an area with weak pull-out strength such as plasterboard in a

double ceiling.

This bracket is an embedded type to reduce the exposed portion of the camera body.

• WV-Q151C: Clear dome cover

• WV-Q151S: Smoked dome cover (approx. 50 % of transmittance)

• Select an installation area that can support the total weight.

If a selected area is too weak to support the total weight, a fall of the product may occur

resulting in injury. Installation work shall be started after sufficient reinforcement.

• Periodic inspections shall be conducted.

Rust on the metal parts or screws may cause a fall of the product resulting in injury. Consult

the dealer for the inspections.

• Do not rub the edges of metal parts with your hand.

Failure to observe this may cause injury.

• Consult the dealer about the installation area to select a strong ceiling area. Make sure that

the installation area is strong enough to hold the total weight of the camera assembly

(approx. 1.7 kg{3.6 lbs.}) before installation.

• The installation area shall have 180 mm {7-1/8"} or more space behind the ceiling.

• The thickness of the ceiling board for installation can range between 9 mm {3/8"} and

40 mm {1-9/16"}.

• Avoid installing in the following locations.

• Locations where it may get wet from rain or water splash (not only outdoor)

• Locations where a chemical agent is used such as a swimming pool

• Locations subject to steam and oil smoke such as a kitchen

• Locations near flammable gas or vapor

• Locations where radiation or x-ray emissions are produced

• Locations subject to strong magnetic field or radio waves

• Locations where it may be damaged by briny air such as seashores

• Locations where the temperature is not within –10 °C - +50 °C {14 °F - 122 °F}.

• Locations subject to vibrations (This product is not designed for on-vehicle use.)

• Locations where the temperature may rapidly change such as the peripheral areas of

the air outlets of air conditioners or doors facing outside. (In case of installing the cam-

era in such locations, the dome cover may become foggy or condensation may be

caused on the cover.)

• The screws and bolts must be tightened with an appropriate tightening torque according to

the material and strength of the installation area. After tightening the screws or bolts, per-

form visual check to ensure tightening is enough and there is no backlash.

• The pull-out strength of the installation area shall be 196 N {20 kgf} or more per 1 screw.

• The protection sheet attached to the dome cover shall be peeled off after installation.

180 mm {7-1/8"} or more

Ceiling board: between 9 mm {3/8"}

and 40 mm {1-9/16"}

Major Operating Controls and Their Functions

Decorative cover

Microphone stand*

Fixing screw to be used

for cover fall prevention

Camera mounting

plate

Mounting base

Hole for microphone cable

Dome cover

Safety wire angle (Accessory)

Safety wire (Accessory)

Ceiling mount bracket

Decorative cover

WV-NS202

Dome cover

Ceiling board

Roof space

* If a microphone is used, mount the microphone on the rubber-made microphone stand.

Unless the microphone is used, cut the rubber with a nipper or conduct another treatment.

Inner shell

Installations

Be sure to read "Precautions" on the page xx before installation. The Installation Guide of the

network camera, WV-NS202, shall be read as well.

1. Remove the decorative cover.

qLoosen the fixing screw (unremov-

able) to be used for cover fall pre-

vention.

wUnhook the decorative cover from

the hooks (3 positions) of the cam-

era mounting plate and remove the

decorative cover by turning it coun-

terclockwise.

eTake the inner shell out.

2. Remove the camera mounting plate.

Remove the screws (M4, 3 positions)

and remove the camera mounting plate

by turning it counterclockwise.

Disengage the portion (a) from the hole

(b) (2 positions).

FRONT

LOCK

FRONT

Fixing screw to be used for

cover fall prevention

Hook

FRONT

LOCK

(b)

Camera mount-

ing plate

Screw (M4)

(a)

3. Put Template A (accessory) against the

ceiling and make a hole.

qMake 4 holes of 12 mm {1/2"} in diam-

eter.

wRemove the center part from the tem-

plate.

eMake a hole of 160 mm {6-5/16"} in

diameter.

* The hole shape is shown below.

4. Install two anchor bolts (M10 recommended) into the concrete ceiling.

qDetermine the anchor bolt length by use of Template B (accessory).

wPosition the nut by use of Template B (accessory). (The distance between the bottom

surfaces of the ceiling board and nut shall be 136 mm {5-3/8"}.)

Note: If there is already an anchor bolt installed, the anchor bolt can be used as a second

anchor bolt. Make sure that the distance between the 1st and 2nd anchor bolts is 1 000

mm {39-3/8"} or less before use.

Template B

Ceiling board

Install the anchor bolt in the center of the hole

Determine the anchor bolt length

136 mm {5-3/8"}

Use a nut

Anchor bolt

ø12 mm {1/2"}

(4 positions)

Ceiling face

ø160 mm

{6-5/16"}

Template A

5. Mount the safety wire angle (accessory) on the 2nd anchor bolt and connect the safe-

ty wire (accessory) to the angle.

qDisconnect the safety wire from the

safety wire angle.

wEngage the face marked qwith the

anchor bolt.

eBend the face marked w.

rConnect the safety wire to the safety

wire angle again.

Note: To use the anchor bolt that was already installed, the use of 2 spacer nuts is helpful.

6. Connect the mounting base to the tip

of the safety wire.

Spacer nuts

Safety wire

Spacer nuts

Safety wire angle

Existing anchor bolt

Upper side

Lower

side

Safety wire

wInsert

qDisconnect

eBend

Mark w

Mark q

rConnect

Safety wire angle

Anchor bolt

Safety wire (Accessory)

Mounting base

Insert the mounting

base into the hole

Roof space

Ceiling board

fixing screw

Ceiling

board fixing

bracket

Insert the anchor bolt

Nut

Double nuts

Turn clockwise

7. Insert the mounting base into the hole

made in Step 1.

8. Secure the mounting base to the ceil-

ing board with the ceiling board fixing

screws (4 positions).

qEngage the top of the mounting base

with the 1st anchor bolt.

wSecure the mounting base by turning

the ceiling board fixing screws clock-

wise.

Turning the ceiling board fixing

screws clockwise provides ceiling

board tightening between the bottom

of the mounting base and ceiling

board fixing bracket resulting in

mounting base securing.

(Recommended tigtening torque:

0.78 N·m {8.0 kgf·cm}

eSecure the mounting base with dou-

ble nuts.

Important: When securing this bracket

on the ceiling, make sure that the

four ceiling board fixing brackets are

open as shown in the figure.

9. Prepare the cables.

Run the cables from the cable inlet.

Important: The cables shall be run from

the opposite side of the mark,

FRONT. Failure to observe this

makes the cables unconnectable.

FRONT

Cable inlet

1st anchor bolt

Ceiling board

10. Install the inner shell.

Slide the covers located on the both lat-

eral sides of the camera and put the

inner shell on the camera until the hooks

inside the inner shell are held in the

holes of the camera (until a click is

heard).

Important: Put the inner shell down on

the camera until the outside cover of

the camera cannot be seen from the

opening (from which the camera

lens is visible) of the inner shell. If

this integration is not successfully

performed, the inner shell may be

removed or the hidden part at the

top of the screen may become larg-

er in the WIDE mode.

How to remove the inner shell

Press the inner shell from the front and rear

sides inward (at the same vertical position as

the hooks) to bend the shell and remove the

shell from the camera.

Cover

Hook

Put on until a click is

heard

Press from the front and rear

sides inward to bend

Inner shell

FRONT

LOCK

Mounting base

Safety wire

FRONT

LOCK

Stationary portion

Center of the

camera mounting

plate

Camera fixing

screw

Lock plate

Guide

Rotating portion

Safety wire hook

11. Mount the camera on the camera

mounting plate.

qPut the camera onto the camera

mounting plate with aligning the lock

plate of the camera with the guide of

the camera mounting plate and

aligning the center of the camera

mounting plate with the center of the

screw for tripod mounting, and turn

the camera clockwise.

wSecure the camera with 1 piece of

the camera fixing screw (supplied

with the camera).

(Recommended tightening torque:

0.68 N·m {7.0 kgf·cm})

Important: Be sure to mount the camera

with holding the stationary portion of

the camera. Camera mounting with

holding the rotating portion of the

camera may cause trouble.

12. Connect the safety wire to the camera.

qConnect the safety wire locked on

the mounting base to the camera.

Make sure that the apical ring of the

safety wire is engaged with the safe-

ty wire hook of the camera by pulling

the safety wire after connection.

13. Connect the cables to the camera.

Dieses Handbuch passt für folgende Modelle

Andere Panasonic Rack & Stand Handbücher

Panasonic

Panasonic KXTCA817EX Bedienungsanleitung

Panasonic

Panasonic TY-S37PX70WK Bedienungsanleitung

Panasonic

Panasonic TY-ST42P50 Bedienungsanleitung

Panasonic

Panasonic TY-ST65P20 Bedienungsanleitung

Panasonic

Panasonic TY-ST42D1-WG Bedienungsanleitung

Panasonic

Panasonic ET-PFD510 Bedienungsanleitung

Panasonic

Panasonic TY34WDM60J - STAND FOR CT34WDM60 Bedienungsanleitung

Panasonic

Panasonic WV-Q52A Bedienungsanleitung

Panasonic

Panasonic KX-TCA727EX Bedienungsanleitung

Panasonic

Panasonic TY-ST85PF12 Bedienungsanleitung

Panasonic

Panasonic ET-JPC200BK Bedienungsanleitung

Panasonic

Panasonic NN-TK816CSCP Bedienungsanleitung

Panasonic

Panasonic TY-ST103PF9 Bedienungsanleitung

Panasonic

Panasonic PPMF12D Bedienungsanleitung

Panasonic

Panasonic ET-PKL100H Bedienungsanleitung

Panasonic

Panasonic WV-Q62 Bedienungsanleitung

Panasonic

Panasonic CWFE14CM Bedienungsanleitung

Panasonic

Panasonic ET-PKE1000S Bedienungsanleitung

Panasonic

Panasonic TY-ST65P11-K Bedienungsanleitung

Panasonic

Panasonic TY-S58PX600W Bedienungsanleitung

Panasonic

Panasonic NN-TK81LCSCP Bedienungsanleitung

Panasonic

Panasonic TY-ST103PF9 Bedienungsanleitung

Panasonic

Panasonic TY-ST65P20 Bedienungsanleitung

Panasonic

Panasonic TY-VK55LV1 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung