Panasonic CQ-C5302W Bedienungsanleitung

ORDER NO. ACED060610C3

AUTOMOTIVE AFTERMARKET

CQ-C5302W

WMA MP3 CD Player/Receiver with CD Changer Control

SPECIFICATIONS

Specifications*

General

Power Supply DC 12V (11V - 16V),

Test Voltage 14.4V

Negative Ground

Current Consumption Less than 2.2A (CD mode ; 0.5W

4-channels)

Maximum Power Output 50W×4 (at 1kHz)

Tone/SQ Adjustment Range SQ Low/Bass ; ±12dB / (at 60Hz,

80Hz, 100Hz, 200Hz)

SQ Mid ; ±12dB / (at 500Hz,

1kHz, 2kHz, 3kHz)

SQ High/Treble ; ±12dB / (at

10kHz, 12kHz, 15kHz, 18kHz)

Speaker Impedance 4-8

Pre-Amp Output Voltage 2.5V (CD mode; 1kHz, 0dB)

Pre-Amp Output Impedance 200

Subwoofer Output Voltage 2.5V

Subwoofer Output Impedance 200

FM Stereo Radio

Frequency Range 87.5MHz - 108.0MHz

Usable Sensitivity 6dB/ V. (S/N 30dB)

Frequency Response 30Hz-15kHz (±3dB)

Alternate Channel Selectivity 75dB

Stereo Separation 35dB (1kHz)

Image Rejection Ratio 70dB

IF Rejection Ratio 100dB

Signal to Noise Ratio 62dB

AM Radio

Frequency Range 531kHz - 1,602kHz

Usable Sensitivity 28dB/ V (S/N 20dB)

CD Player

Sampling Frequency 8 Times Oversampling

DA Converter 1bit DAC System

Pick-Up Type Astigma 3-beam

Light Source Semiconductor Laser

Wave Length 790nm

Frequency Response 20Hz to 20kHz (±1dB)

Signal to Noise Ratio 96dB

Total Harmonic Distortion 0.01% (1kHz)

Wow and Flutter Below measurable limits

Channel Separation 75dB

Dimensions** (W×H×D) 178×50×155mm

Weight** 1.6kg

* Specifications and the design are subject to possible

modification without notice due to improvements.

** Dimensions and Weight shown are approximate.

-Above specifications comply with EIA standards.

Unauthorized copying and distribution is a violation of law.

1. ABOUT LEAD FREE SOLDER (PbF)

Distinction of PbF PCB:

PCBs (manufactured) using lead free solder will have a PbF stamp on the PCB.

Caution :

- Pb free solder has a higher melting point than standard solder; Typically

the melting point is 50 - 70°F (30 - 40°C) higher. Please use a soldering

iron with temperature control and adjust it to 700 ± 20°F (370 ± 10°C). In

case of using high temperature soldering iron, please be careful not to

heat too long.

- Pb free solder will tend to splash when heated too high (about 1100°F/

600°C)

- This lead free solder will be used for the products after serial No.

1,000,001.

2. LASER PRODUCTS

3. FEATUERS

- Digital servo for reliable playback.

- PLL (Phase Locked Loop) synthesized tuning.

- 18-FM, 6-AM presets with preset scan.

- Removable face plate.

- MP3/WMA Playback from CD-R/RW.

- CD Changer Control.

4. REPLACING THE FUSE

Use fuses of the same specified rating (15amps). Using different substitutes or fuses with higher

ratings, or connecting the product directly without a fuse, could cause fire or damage to the stereo unit.

5. MAINTENANCE

Your product is designed and manufactured to ensure a minimum of maintenance. Use a dry, a soft

cloth for routine exterior cleaning. Never use benzine, thinner or other solvents.

6. NOTES

[RADIO BLOCK]

Do not align the AM/FM package block. When the package block is necessary, it will be supplied already

aligned at the factory.

[CD DECK BLOCK]

This model has no servo alignment points because microcomputer controls the servo circuit.

7. DIMENSIONS

8. WIRING CONNECTION

9. DISASSEMBLY INSTRUCTIONS

9.1. How to remove the Flexible PCB

9.2. How to install the Main P.C.B of the Electric Slide Display

10. TERMINALS DESCRIPTION

10.1. Main Block

IC601 : YESAM288

No.

Port Description I/O Volt (V)

FM AM CD

1PANEL

OPEN

PANEL OPEN

detection

I 5.2 5.2 5.2

2PANEL

PANEL CLOSE

detection

I 0 0 0

3 LCD DI LCD data O 4.7 4.7 4.7

4 BATT BATT detection I 5.1 5.1 5.1

5 ACC ACC detection I 5.1 5 5.1

6 SDA Electronic VOL data I/O 5 5 5

7 SCK Electronic VOL clock O 5 0 5

8 LCD

LCD data I 4.9 4.9 4.9

9 Vss GND - 0 0 0

10 ST FM ST detection I 5.1 5.1 5.1

11 PLL DI

(MO)

PLL data output O 0 0 0

12 PLL

DO (MI)

PLL data input I 5.2 5.2 5.2

13 PLL

CLK

PLL clock output O 5 5 5

14 PLL CE PLL chip enable

output

O 0 0 5

15 CD

RST

CD deck reset output O 5 5 0

16 XM RX XM tuner RX data O 4.8 4.8 4.8

17 LCD

CLK

LCD clock O 4.9 4.9 4.9

18 XM TX XM tuner TX data I 0 0 0

19 CD SO

(MI)

CD Data I 1.4 1.4 1.4

20 CD

SCK

CD clock transmit O 4.9 4.9 4.9

21 Vdd Power supply I 5 5 5

22 CD SI

(MO)

CD Data O 0 0 0

23 NC No Connection - - - -

24 CDC

CLK

CD Changer clock I 0 0 0

25 CONDENSOR

Capacitor for power

supply

- 3.2 3.2 3.2

26 CDC

DATA

CD Changer data I 0 0 0

27 CDC

STB

Changer storobe

signal input

I 0 0 0

28 CD IN DISC In detection I 4.9 4.9 0.4

29 DECK

CONT

DECK power supply

control output

O 5 5 5

No.

Port Description I/O Volt (V)

FM AM CD

30 CD

STB

Strobe signal for CD

communication

O 3.3 3.3 3.3

31 NC No Connection - - - -

32 Avdd Power supply of D/A

converter

I 5.1 5.1 5.1

33 AVREF Reference voltage for

D/A converter

I 5.1 5.1 5.1

34 AVGND Reference GND for D/

A converter

I 0 0 0

35 AVSS GND for A/D and D/A

converter

I 0 0 0

36 SD FM/AM signal strength I 0.3 0 0.3

37 INIT A Initializ A I 0 0 0

38 INIT B Initializ B I 0 0 0

39 A IN SPE.ANA A.IN I 0 0 0

40 Vss GND I 0 0 0

41 CD A0 Signal output

according to

command employment

O 0 0 5.1

42 NC No Connection - - - -

43 NC No Connection - - - -

44 NC No Connection - - - -

45 CD

SW1

CD mechanism switch I 0 0 0

46 CD

SW2

CD mechanism switch I 5 5 0

47 MOD0 Operating mode input

I 5.2 5.2 5.2

48 MOD1 Operating mode input

I 5.1 5.1 5.1

49 MOD2 Operating mode input

I 0 0 0

50 H

STANDBY

External standby input I 5.1 5.1 5.1

51 DC DC

CNT

(NC)

- - - - -

52 FP

MOTOR1

Front open/close

control 1

O 5 5 5

53 FP

MOTOR2

Front open/close

control 2

O 5 5 5

54 V

CNT1

Panel driving voltage

control 1

O 0 0 0

55 V

CNT2

(NC)

- - - - -

56 SA

CLK

Spectrum analizer

clock

O 5 4.9 4.9

CONT CLK clock

No.

Port Description I/O Volt (V)

FM AM CD

57 EXT

MUTE

TEL/NAVI MUTE input I 5.4 5.4 5.4

58 AMP

CONT

External AMP control O 5 5 5

59 BZ-

OUT

Buzzer output O 0 0 0

60 ANT

CONT

Motor antenna control O 5 5 0

61 DIM1

(NC)

- - - - -

62 DIM2

(NC)

- - - - -

63 CDC

REM

OUT

Remote control data

for CD Changer

O 5 5 5

64 CDC

SENS

CDC 1/2 detection I 5.1 5.1 5.1

65 CDC 1/

CDC 1/2 change

output

O 0 0 0

66 NC - - - - -

67 REMO

Main wake-up request I 4.9 4.9 4.9

68 NC - - - - -

69 RDS

CLK

(NC)

- - - - -

70 NC - - - - -

71 RD

DATA

(NC)

- - - - -

72 MAIN

CONT

MAIN power supply

control

O 5 4.9 4.9

73 INV

CONT

INV power supply

control

O 5.1 5 5

74 AF

MUTE

AF MUTE control O 5.1 5.1 5.1

75 RESET Reset input I 5.1 5.1 5.1

76 NC No Connection - - - -

77 NC No Connection - - - -

78 NC - I 0 0 0

79 Vss GND I 0 0 0

80 X1 Crystal oscillator input I 2.1 2.1 2.1

81 X2 Crystal oscillator

output

O 2.5 2.5 2.5

82 Vdd Power supply I 5.1 5.1 5.1

83 P00 Pldaun port for writing I 0 0 0

84 P01 Pull-up port for writing I 5.1 5.1 5.1

No.

Port Description I/O Volt (V)

FM AM CD

85 OFFSET

DET

PWR-IC offset

detection

I 0 0 0

86 STBY PWR-IC STBY control

output

O 5.1 5.1 5.1

87 AMP

MUTE

PWR-IC MUTE control

output

O 0 0 0

88 ILL

SENS

(NC)

- - - - -

89 NC - - - - -

90 EP DO

(MI)

(NC)

- - - - -

91 EP D0

(M0)

(NC)

- - - - -

92 EP SK

(NC)

- - - - -

93 SUB

W U

REQ/

LCD

Sub Wake-up request O 0 0 0

94 DISPM

CNT

Power supply control

for display

O 0 0 0

95 EJE

ILL

(NC)

- - - - -

96 Rotary

Rotary Encoder 1 I 4.9 5 5

97 Rotary

Rotary Encoder 2 I 4.9 4.9 5

98 S LED Security LED control

output

O 0 0 0

99 PANEL

PANEL detect I 5.3 5.3 5.3

100 EP CS

(NC)

- - - - -

10.2. Display Block

IC901 : YESAM168

No.

Port Description I/O (V)

1-35 SEG3-37 LCD segment data O 2.5

36-51 SEG40-55 LCD segment data O 2.5

52-55 COM1-4 LCD common O 2.5

56,57 SEG39,38 Not used - -

58-61 KS3-6 Key scan O 5.0

62-66 Kl1-5 Key data I 0

67 VDD +5V power supply - 5.0

68 VLCD VLCD terminal - 4.8

69 VLCD1 VLCD1 terminal - 3.3

70 VLCD2 VLCD2 terminal - 1.7

71 VSS Ground - 0

72 TEST (Connecting to ground) - 0

73 OSC Oscillator terminal - 3.9

74 RESET Reset I 4.8

75 DO Key data output O 5.0

76 CE LCD driver chip enable I 0

77 CLK LCD clock I 4.9

78 DI LCD data I 4.9

79,80 SEG1,2 LCD segment data O 2.5

10.3. CD Servo Block

IC401 : YESAM348

No.

Port Descriptions I/O (V)

1 CVSS1 GND - 0

2 - - - -

3 CVSS2 GND - 0

4 DVDD1 I/O system (3.3V) power

supply

- 3.3

5 A10 Address bus of FLASH ROM O 0

6 - - - -

7 A11 Address bus of FLASH ROM O 3.3

8 A12 O 3.3

9 A13 O 3.3

10 A14 O 3.3

11 A15 O 3.3

12 /

CVDD1

CORE CPU system (1.6V)

power supply

- 1.6

13 - - - -

14 DVSS1 GND - 0

15 CVSS3 GND - 0

No.

Port Descriptions I/O (V)

16 /

CVDD2

I/O system (3.3V) power

supply

- 1.6

17 - - - -

18 - - - -

19 READY - - 3.3

20 /PS FLASH ROM selection

signal

O 3.3

21 - - - -

22 - - - -

23 R/W Lead/light signal to FLASH

ROM

O 3.3

24 /

MSTRB

Memory access signal O 3.3

25 - - - -

26 /MSC - - 3.3

27 MUTE Mute signal output (H:Mute

on)

O 0

28 - - - -

29 - - - -

30 /HOLD - - 3.3

31 BIO SUBO input I 0

32 MP/MC Operation mode setting

(external pull-up)

I 3.3

33 DVDD2 I/O system (3.3V) power

supply

- 3.3

34 CVSS4 GND - 0

35 BD R1 GND I 0

36 - - - -

37 CVSS5 GND - 0

38 - - - -

39 - - - -

40 DVSS2 GND - 0

41 CLK C

AUDIO bit clock input I 1.6

42 SCK Clock input I 3.3

43 LRCK

C M

AUDIO L/R identifying

signal input

I 1.6

44 CDFS Serial frame sink signal

input

I 2.6

45 DATA

AUDIO serial data input I 1.6

46 - - - -

47 SI Serial data input I 0

48 CLK M

AUDIO bit clock output O 1.6

49 SCK Clock input I 3.3

50 CVSS6 GND - 0

51 - - - -

Andere Handbücher für CQ-C5302W

Inhaltsverzeichnis

Andere Panasonic Empfänger Handbücher

Panasonic

Panasonic HD-PLC DA-PU100 Bedienungsanleitung

Panasonic

Panasonic SA-HR45E Bedienungsanleitung

Panasonic

Panasonic SA-HE70S-U Operating Bedienungsanleitung

Panasonic

Panasonic CQ-KO2EG Bedienungsanleitung

Panasonic

Panasonic CQ-VD5505W Bedienungsanleitung

Panasonic

Panasonic SHFX71 - WIRELESS SYSTEM Bedienungsanleitung

Panasonic

Panasonic SA-G90 Bedienungsanleitung

Panasonic

Panasonic SH-FX50T Bedienungsanleitung

Panasonic

Panasonic RF-P50 Bedienungsanleitung

Panasonic

Panasonic CQ2650EU - AUTO RADIO/CASSETTE Bedienungsanleitung

Panasonic

Panasonic SAHE9 - RECEIVER Bedienungsanleitung

Panasonic

Panasonic RF-SW250 Bedienungsanleitung

Panasonic

Panasonic K-SRC14 Bedienungsanleitung

Panasonic

Panasonic SA-DT300E Bedienungsanleitung

Panasonic

Panasonic CRD4500R - RECEIVER Bedienungsanleitung

Panasonic

Panasonic CZ-RWRU3 Bedienungsanleitung

Panasonic

Panasonic RF-U160 Bedienungsanleitung

Panasonic

Panasonic SH-FX60 - Wireless Audio Delivery System Bedienungsanleitung

Panasonic

Panasonic CF-AA Series Bedienungsanleitung

Panasonic

Panasonic SA-XR50S Bedienungsanleitung

Panasonic

Panasonic CZ-CFUNC2 Bedienungsanleitung

Panasonic

Panasonic WVRC150 - CONTROLLER Bedienungsanleitung

Panasonic

Panasonic DNUA-P75 Bedienungsanleitung

Panasonic

Panasonic CQ-4400U Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung