Panasonic CZ-RTC5A Bedienungsanleitung
Panasonic Corporation
1006 Kadoma, Kadoma City, Osaka, Japan
Operating Instructions
High-spec Wired Remote Controller
Model No. CZ-RTC5A
Installation Instructions
Separately Attached.
English
Before operating the unit, read these operating instructions thoroughly and keep them for future
reference.
CV6233312187
Panasonic Corporation
http://www.panasonic.com
2(EN)
Safety Precautions
CAUTIONS
This appliance is intended to be used by expert or
trained users in shops, in light industry and on farms, or
for commercial use by lay persons.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
WARNING
Do not use this appliance in a potentially explosive
atmosphere.
• Do not operate with wet hands.
• Do not wash with water.
In case of malfunction of this appliance, do not repair by
yourself. Contact the sales or service dealer for repair.
In case of emergency, remove the power plug
from the socket or switch off the circuit breaker
or the means by which the system is isolated
from the mains power.
WARNING CAUTION
This symbol refers to a hazard or unsafe
practice which can result in severe personal
injury or death.
This symbol refers to a hazard or unsafe
practice which can result in personal injury or
product or property damage.
Matters to be observed Prohibited matters
3
(EN)
Note:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
FCC Caution: To assure continued compliance, follow
the attached installation instructions. Any changes
or modifi cations not expressly approved by the party
responsible for compliance could void the user’s authority
to operate this equipment.
4(EN)
Preparations
How to Use Setting Change When
Necessary
Page
Thank you for purchasing the
Panasonic high-spec wired remote
controller.
Read the Operating Instructions
carefully for safe use. This
manual describes the Operating
Instructions of the wired remote
controller. Read this manual as
well as operating instructions
supplied with indoor units and
outdoor units.
Be sure to read the “Safety
Precautions” (P.2, 3) before
using.
Keep this manual with operating
instructions supplied with indoor
units and outdoor units in a safe
place.
Be sure to keep this manual in a
place easily accessible by users.
In the case of user change, be
sure to give this manual to the
new user.
NOTICE
The English text is the original
instructions. Other languages
are translation of the original
instructions.
CONTENTS
Safety Precautions ...............................2
Part Names ...........................................5
• Control panel .......................................5
• Screen display .....................................6
Basic Operations..................................8
Menu List ............................................10
Flap Setting for Each Indoor Unit .....12
• FLAP ..................................................12
Flap Setting for Each Air Outlet ........13
• Lock indiv. fl ap ...................................13
Timer Reservation ..............................14
• ON/OFF timer ....................................14
• Weekly timer overview .......................15
• Weekly timer ......................................16
Filter Information ................................20
Quiet Operation/Power Consumption Monitor
...22
Energy Saving ....................................24
• ECONAVI ...........................................24
• Temp auto return ................................30
• Temp range ........................................30
• Auto shutoff ........................................32
• Schedule peak cut .............................34
• Repeat off timer .................................36
Outing Function .................................37
Initial Settings ....................................39
• Clock/Clock type/Operation lock ........39
• Controller name .................................40
• Touch sound/Contrast/
Backlight/Language ...........................41
•
Password change/Temp sensor/
Main/sub/Vent output/Contact address
...42
• External device interlock ....................44
• Rotation setting ..................................46
Ventilation Setting ..............................49
Setting List ..........................................50
Troubleshooting .................................52
Specifi cations .....................................54
5
(EN)
Part Names Control panel
Note
LCD screen
Return button
Returns to the previous screen.
Menu button
Displays the menu
screen (P. 10).
Operation indicator
Illuminates during operation.
Blinks during alarm.
Start/Stop button
Starts/Stops operation.
Enter button
Fixes the selected content.
Press centre No glove No pen
Energy saving
button
Switches Energy
saving/Normal
operation.
Cross key buttons
Selects an item.
Up
Down
RightLeft
6(EN)
When inspection is
required (P.52)
Appears if there is a problem on ECONAVI.
Top screen
Item selection screen Operation stop screen
Lock screen display
Remote
controller
name (P.40)
Setting
information
icon
(Next page)
Operation guide (P.7)
Cursor
Operation
mode
Set
temperature
Fan speed
Flap
[Operation lock] is functioning. (P.39)
To cancel lock
Press button for 4 seconds.
The indoor unit is stopped or slight blow operation is in process.
Part Names Screen display
* Only the partial settings can be checked on the top screen. To check all the settings (P.50)
Operation is
locked. (P.39)
Present time &
day (P.39)
Appears when ECONAVI is
being set to ON.
(When the ECONAVI panel is
attached)
7
(EN)
Menu screen (P.10)
Screen name Present time & day
The currently operable content is simply
displayed.
• ▲▼◄►: Cross key buttons
• : Enter button
Icon Description Page
The indoor unit fi lter needs to be cleaned. P.20
The engine oil needs to be replaced.
(Only when using a gas heat pump air conditioner.) -
Switching operation modes is prohibited.
(Switching to Auto mode is also prohibited.) -
Remote control operation is restricted by a central control device. -
[ON/OFF timer] is set. P.14
[Weekly timer] is set. P.15
Energy saving operation is in process. P.8
Fresh air is used for ventilation.
(Only when connecting a heat exchange ventilation unit or
connecting a commercially sold fan.)
P.49
Prevents the room temperature from increasing too much (or
decreasing too much) when no one is in the room. P.37
[Circulation] is set.
(Not displayed when all the above icons are displayed.) P.29
Setting information icon
(Setting information icons displayed on the top screen)
Operation guide
8(EN)
Basic Operations
1Start operation.
Press .
(The operation indicator illuminates.)
To change the setting
(P.10)
To turn the energy saving
operation ON/OFF
Press during operation.
(Only for models equipped with the
energy saving function.)
To stop
(The operation indicator turns off .)
2Select the item to set.
Press ◄ ►.
3Change the setting.
Press ▲▼ → .
(The cursor disappears.)
Energy saving operation
is in process.
Operation indicator
Note
Operation modes that cannot be set are not displayed.
The swing and airfl ow direction on the remote control is not synchronised with the fl ap movement.
The fl ap display diff ers from the actual fl ap angle.
Pressing after recovery from mains power failure will resume operation with
the contents before mains power failure has occurred.
If no operation is performed for a certain period of time, the backlight turns off to
save electricity. (Press any button for illumination.)
The energy saving operation restricts the maximum current value, resulting in
decreased cooling/heating performance.
(If the current of outdoor units does not reach the peak due to low load operation,
the current value is not restricted.)
For models that cannot change the airfl ow direction, the airfl ow direction is not displayed.
When restricting the set temperature range (P.31)
The fan speed and airfl ow direction in cooling/drying operation can be adjusted with 3
levels if controlling using one remote controller while assigning an indoor unit (e.g. ceiling-
hung type) which has a 3-level adjustment of fan speed and airfl ow direction in cooling /
drying operation as main unit, and assigning a 4-way ceiling cassette type as sub unit.
9
(EN)
Perform the following operations in step 2 on page 8.
Operation mode (e.g. Cool, Heat, etc.)
Press ◄.
* Auto:
The mode is
automatically
switched to
Cool or Heat to
achieve the set
temperature.
Heat
Dry
Cool
Fan
Auto
Set temperature
Press . (When the cursor is not
visible)
• Cool/Dry : 18 °C to 30 °C
• Heat : 16 °C to 30 °C
• Auto : 17 °C to 27 °C
Fan speed
Press ►.
Flap
Press ► 2 times.
Flap Setting for Each Indoor
Unit (P.12)
• : Swing
• Pressing ▲▼
during swing can
stop the fl ap at your
preferred position.
Cursor
* Depending on the model, either of the
displays appears.
* Auto: Cannot be selected in Fan
mode.
* Depending on the model, selectable
airfl ow directions may diff er.
High
Medium
Low
Auto
**
10 (EN)
1Display the menu screen.
To return to the previous screen
Press .
When no operation is performed
in each setting screen for several
minutes
The display returns to the top screen.
2Select the menu item.
▲ ▼ →
To turn the page
Press ◄ ►.
Selectable menus (1 to 13)
For details of screen examples,
see the next page.
Menu List
Andere Handbücher für CZ-RTC5A
1
Inhaltsverzeichnis
Andere Panasonic Fernbedienung Handbücher
Panasonic
Panasonic EUR511111 Bedienungsanleitung
Panasonic
Panasonic CZ-RWSU2N Bedienungsanleitung
Panasonic
Panasonic CZ-RWSU3U Bedienungsanleitung
Panasonic
Panasonic CZ-RELC2 Bedienungsanleitung
Panasonic
Panasonic WVCU550B - SYSTEM CONTROLLER Bedienungsanleitung
Panasonic
Panasonic EUR7722KN0 Bedienungsanleitung
Panasonic
Panasonic KX-HNK102 Bedienungsanleitung
Panasonic
Panasonic CZ-RE2C2 Bedienungsanleitung
Panasonic
Panasonic CZ-RTC6BL Bedienungsanleitung
Panasonic
Panasonic AJRC10G - REMOTE CONTROL UNIT Bedienungsanleitung
Panasonic
Panasonic AK-HRP200G Bedienungsanleitung
Panasonic
Panasonic EUR511517 Bedienungsanleitung
Panasonic
Panasonic EUR511511 guide Bedienungsanleitung
Panasonic
Panasonic WV-CU161 Bedienungsanleitung
Panasonic
Panasonic EUR7702KE0 Bedienungsanleitung
Panasonic
Panasonic EUR511151 Bedienungsanleitung
Panasonic
Panasonic WV-RC700 Bedienungsanleitung
Panasonic
Panasonic EUR7722X80 Bedienungsanleitung
Panasonic
Panasonic DMW-RSL1 Bedienungsanleitung
Panasonic
Panasonic CZ-RD514C Installations- und Betriebshandbuch
Beliebte Fernbedienung Handbücher anderer Marken
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
HR Matic
HR Matic HR MULTI 3 Bedienungsanleitung
