Panasonic WV-CP300 Series Bedienungsanleitung

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

The model number is abbreviated in some descriptions in this manual.

This illustration represents WV-CP300.

Lens: Option

Operating Instructions

Color CCTV Camera

Model No: WV-CP310, WV-CP314

WV-CP300, WV-CP304

Preface

About the user manuals

The operating instructions of the camera consist of 2 sets: these operating instructions (PDF)

and Installation Guide.

This document explains how to configue the settings of the camera.

Refer to the installation guide for further information about how to install the camera.

Adobe®Reader®is required to read PDF. When the Adobe®Reader® is not installed on the

PC, download the latest Adobe®Reader®from the Adobe web site and install it.

Trademarks and registered trademarks

Adobe, Acrobat Reader and Reader are either registered trademarks or trademarks of Adobe

Systems Incorporated in the United States and/or other countries.

About notations

The following notations are used when describing the functions limited for specific models.

The functions without the notations are supported by all models.

CP310

CP300

: The functions with this notation are available when using the model WV-CP310 and

WV-CP314.

CP310

CP300

: The functions with this notation are available when using the model WV-CP300 and

WV-CP304.

Contents

Preface .......................................................................................................................................... 2

About the setup menus ................................................................................................................ 4

List of setup menu ...................................................................................................................... 4

Basic operation ............................................................................................................................ 5

Screen transition diagram

CP310

CP300

................................................................................................ 7

Screen transition diagram

CP310

CP300

................................................................................................ 8

Camera title setting [CAMERA ID]................................................................................................. 9

Camera operation setting [CAMERA SETUP] ............................................................................. 10

Register a scene file [SCENE1/SCENE2].................................................................................. 10

Light quantity control method selection [ALC/ELC] ................................................................. 11

Back light compensation function........................................................................................ 11

Electronic shutter setting [SHUTTER] ...................................................................................... 12

Gain control setting [AGC] ....................................................................................................... 12

Electronic sensitivity enhancement setting [SENS UP] ............................................................ 13

White balance setting [WHITE BAL] ......................................................................................... 13

Manual fine adjustment of white balance ........................................................................... 14

Digital noise reduction function setting [DNR] .......................................................................... 15

Black-and-white mode setting [D&N (IR) ]

CP310

CP300

[D&N (ELE) ]

CP310

CP300

...................................... 15

VMD setting [VMD] ................................................................................................................... 17

Set motion detection............................................................................................................ 17

Setting of scene change detection ..................................................................................... 19

Camera system setting [SYSTEM SETUP] ................................................................................. 20

Synchronization method selection [SYNC]............................................................................... 20

Privacy zone setting [PRIVACY ZONE] ..................................................................................... 20

Image stabilizer setting [STABILIZER]....................................................................................... 21

Electronic zoom setting [EL-ZOOM] ........................................................................................ 21

Upside-down setting [UPSIDE-DOWN] ................................................................................... 22

Lens distortion correction [LDC] ............................................................................................... 22

Special menu setting [SPECIAL SETUP] .................................................................................... 23

Chroma level adjustment [CHROMA GAIN] ............................................................................. 23

Aperture level adjustment [AP GAIN] ........................................................................................ 23

Pedestal level adjustment [PEDESTAL] ................................................................................... 23

Chroma phase (hue) adjustment [HUE] .................................................................................... 23

Flaw compensation [PIX OFF] .................................................................................................. 24

Communication setting [COMMUNICATION] .......................................................................... 24

Default resetting [CAMERA RESET] ......................................................................................... 25

Serial number viewing [SER.NO.] ............................................................................................. 25

Camera language selection [LANGUAGE SETUP] ..................................................................... 26

Shortcut operation ..................................................................................................................... 27

About the setup menus

Performing each setting item in the setup menu should be completed in advance to use this unit.

Perform the settings for each item in accordance with the conditions of the camera shooting area.

List of setup menu

Setup item Description

CAMERA ID

This item specifies the camera title. The camera title that indicates the camera

location and other information about the camera is created with alphanumeric

characters and symbol, and then displayed on the screen.

CAMERA Performs the camera operation settings.

SCENE 1/

SCENE 2

Selects a scene file. It is possible to register and save the settings as a scene file

in case that it is necessary to change the settings such when shooting at night.

ALC/ELC Selects the method of controlling the quantity of light in accordance with the lens

to be used.

SHUTTER Specifies the electronic shutter speed.

AGC Specifies gain adjustment.

SENS UP Specifies electronic sensitivity enhancement.

WHITE BAL Specifies white balance adjustment.

DNR Selects the level of the digital noise reduction function.

D&N (IR/ELE) Performs each setting regarding the black-and-white mode such as switching

between color and black-and-white images.

VMD Performs settings regarding VMD (Video Motion Detection)

SYSTEM Performs the settings regarding the camera system such as synchronization and

privacy zone.

SYNC Specities the synchronization type.

PRIVACY ZONE Hides undesired portions in the camera shooting area.

STABILIZER Decides whether or not to enable the image stabilizer.

EL-ZOOM Switches the electronic zoom on and off.

UPSIDE-DOWN Flips the camera images vertically or horizontally.

LDC Adjusts the lens distortion correction to convert the image so that it matches the

square monitor.

SPECIAL

CHROMA GAIN Adjusts the chroma level (color density).

AP GAIN Adjusts the aperture level.

PEDESTAL Adjusts the pedestal (brightness) level.

HUE Adjust the chroma phase (hue).

PIX OFF Corrects image defects such as flaws.

COMMUNICATION

Performs the communication setting of the system with a receiver into which this

unit is integrated.

CAMERA

RESET Restores the settings in the setup menu to the default settings.

SER.NO. Displays the serial number of this unit.

LANGUAGE Selects a language to be used in the setup menu.

Screenshot 2

The setup mode changes to "ENABLE", and

the setup menu becomes ready to be set.

Step 3

Move the cursor to the item to be set, and

press the [SET] button.

Screenshot 1

Hold down the [SET] button for about 2 sec-

onds to call up the top screen of the setup

menu.

Step 1

Press the [UP] button or the [DOWN] button

to move the cursor to "END".

Step 2

Press the [RIGHT] button to move the cursor

to "SETUP", and press the [SET] button to

change the setup mode from "DISABLE" to

"ENABLE".

MODEL WV-CP310 SERIES

CAMERA ID OFF

CAMERA

SYSTEM

SPECIAL

LANGUAGE

END SETUP DISABIE

MODEL WV-CP310 SERIES

CAMERA ID OFF

CAMERA

SYSTEM

SPECIAL

LANGUAGE

END SETUP ENABLE

The operations in the setup menu are performed with the operation buttons after calling up the

setup menu on the connected video monitor.

The description below explains how to operate the setup menu basically.

Screenshots of WV-CP310 are shown as an example.

Basic operation

Screenshot 3

The selected setup screen in the setup menu

appears on the screen.

Note:

 • If the top screen of the setup menu is

called up with the operation buttons

while the camera is operated, the setup

mode is always "DISABLE" to prevent

operation errors.

To perform settings in the setup menu,

change the setup mode to "ENABLE".

 • Thecursorisareverselyhighlightedpart.

Step 4

Perform the settings for each item.

 • Selectionofsettingitem:

Press the [UP] button or [DOWN] button

to move the cursor.

 • Changeofsettings:

Press the [RIGHT] button or [LEFT ] button.

 • Displayofadvancedsetupscreen:

Press the [SET] button when “ ” is

attached to the target setting item.

 • Returntoprevioussetupscreen:

Move the cursor to "RET" and press the

[SET] button.

 • Returntothetopscreen:

Move the cursor to "TOP" and press the

[SET] button, to display the top screen of

the setup menu.

Step 5

Move the cursor to “END” and press the

[SET] button to return to the camera image

screen, or wait about 5 minutes and the

setup menu will automatically close.

**CAMERA SETUP**

SCENE1

ALC/ELC ALC

SHUTTER OFF

AGC ON(HIGH)

SENS UP OFF

WHITE BAL ATW1

DNR HIGH

AUTO1

VMD

RET TOP END

D&N(IR) OFF

Screen transition diagram

CP310

CP300

...I... 0

HUE

Top screen “CAMERA ID” screen

“CAMERA SETUP” screen

“SYSTEM SETUP” screen

“SPECIAL SETUP” screen

“LANGUAGE SETUP” screen

MODEL WV-CP310 SERIES

CAMERA ID OFF

CAMERA

SYSTEM

SPECIAL

LANGUAGE

END SETUP DISABLE

**LANGUAGE SETUP**

LANGUAGE ENGLISH

SET

RET TOP END

**CAMERA ID**

0123456789

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

().,'":;&#!?=

+-*/%$

SPACE POSI

RET TOP END RESET

................

**SYSTEM SETUP**

SYNC INT

PRIVACY ZONE OFF

STABILIZER OFF

EL-ZOOM OFF

UPSIDE-DOWN OFF

- +

LDC I...... 0

RET TOP END

**SPECIAL SETUP**

CHROMA GAIN ....I..160

AP GAIN ...I... 32

PEDESTAL .I..... 15

- +

PIX OFF

CAMERA RESET PUSH SET

SER.NO. XXXXXXXX

COMMUNICATION COAX

RET TOP END

**CAMERA SETUP**

SCENE1

ALC/ELC ALC

SHUTTER OFF

AGC ON(HIGH)

SENS UP OFF

WHITE BAL ATW1

DNR HIGH

AUTO1

VMD

RET TOP END

D&N(IR) OFF

Screen transition diagram

CP310

CP300

Top screen “CAMERA ID” screen

“CAMERA SETUP” screen

“SYSTEM SETUP” screen

“SPECIAL SETUP” screen

“LANGUAGE SETUP” screen

MODEL WV-CP300 SERIES

CAMERA ID OFF

CAMERA

SYSTEM

SPECIAL

LANGUAGE

END SETUP DISABLE

**LANGUAGE SETUP**

LANGUAGE ENGLISH

SET

RET TOP END

**CAMERA ID**

0123456789

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

().,'":;&#!?=

+-*/%$

SPACE POSI

RET TOP END RESET

................

**SYSTEM SETUP**

SYNC INT

PRIVACY ZONE OFF

STABILIZER OFF

EL-ZOOM OFF

UPSIDE-DOWN OFF

- +

LDC I...... 0

RET TOP END

**SPECIAL SETUP**

CHROMA GAIN ....I..160

AP GAIN ...I... 32

...I... 0

PEDESTAL

HUE .I..... 15

- +

PIX OFF

CAMERA RESET PUSH SET

SER.NO. XXXXXXXX

COMMUNICATION COAX

RET TOP END

**CAMERA SETUP**

SCENE1

ALC/ELC ALC

SHUTTER OFF

AGC ON(HIGH)

SENS UP OFF

WHITE BAL ATW1

DNR HIGH

OFF

VMD

RET TOP END

D&N(ELE) OFF

This item specified the camera title. The camera title is named with up to 8 characters when

using only Chinese characters, and up to 16 characters when using only English letters or num-

bers. Chinese character, English letters and numbers can be used together. The "CAMERA ID"

display can be turned on or off on the monitor screen.

Step 1

Select "ON" for "CAMERA ID", and then press the [SET] button.

→The "CAMERA ID" appears.

Important:

 • When"CAMERAID"issetto"OFF",thecameratitledoesnotappearevenaftersettingthe

camera title.

Step 2

Move the cursor to the target item with use of the [UP], [DOWN], [RIGHT], and [LEFT] buttons,

and press the [SET] button to enter the character.

→The entered characters are displayed in the editing area.

<Characterentry>

 • ToinputEnglishlettersandnumbers,movethecursortothedesiredletterornumberand

press the [SET] button, to display the screen after enter of English letters and numbers.

 • Toreviseacharacter,movethecursorto(↑) in the editing area, then move the cursor (↑) to

an incorrect character with use of the right or left button, and enter a correct character.

 • Toenterablank,movethecursorto"SPACE"andpressthe[SET]button.

 • Todeletealltheenteredcharacters,movethecursorto"RESET"andpressthe[SET]button.

Step 3

Move the cursor to "POSI" and press the [SET] button after title entered.

→The display positioning screen appears.

Step 4

Use the [UP], [DOWN], [RIGHT], and [LEFT] buttons to decide the title position and press the [SET] button.

→The title position is specified.

Camera title setting [CAMERA ID]

FLOOR 1

Editing area

Top screen "CAMERA ID" screen Display positioning screen

MODEL WV-CP310 SERIES

CAMERA ID ON

CAMERA

SYSTEM

SPECIAL

LANGUAGE

END SETUP ENABLE

**CAMERA ID**

0123456789

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

().,'":;&#!?=

+-*/%$

SPACE POSI

RET TOP END RESET

................

Camera operation setting [CAMERA SETUP]

The following settings related to camera actions can be configured on the "CAMERA SETUP"

screen displayed from the top screen. Refer to page 5-6 for how to call up the screen.

The settings configured on the "CAMERA SETUP" screen will be saved as a scene file.

1Register a scene file [SCENE1/SCENE2]

It is possible to register 2 patterns of scene file. When different settings are to be applied

between day and night, SCENE1 can be applied in the daytime and SCENE2 at night. Change

between the scene files can be made by shortcut operation. (page 27) "SCENE1" is set as

the default setting.

Screen when "SCENE1" is selected Screen when "SCENE2" is selected

**CAMERA SETUP**

SCENE1

ALC/ELC ALC

SHUTTER OFF

AGC ON(HIGH)

SENS UP OFF

WHITE BAL ATW1

DNR HIGH

AUTO1

VMD

RET TOP END

D&N(IR) OFF

**CAMERA SETUP**

SCENE2

COPY(SCENE1)

ALC/ELC ALC

SHUTTER OFF

AGC ON(HIGH)

SENS UP OFF

WHITE BAL ATW1

DNR HIGH

AUTO1

VMD

RET TOP END

D&N(IR) OFF

Step 1

After confirming that "SCENE1" is selected, configure the settings of "ALC/ELC" through

"VMD". (page 11-19)

To change the scene files, go to step 2.

Step 2

Move the cursor to "SCENE1" and use the [RIGHT] or [LEFT] button to select "SCENE2".

→The screen changes and displays “SCENE2”.

Step 3

To configure the settings of "SCENE2" using the settings of "SCENE1", press the [SET] button

after moving the cursor to "COPY(SCENE1)".

→The settings of "SCENE1" will be copied to "SCENE2".

Step 4

Edit the settings to be changed.

The number displayed at the right side of the title on

each setting screen indicates a scene file number.

Step 5

Move the cursor to "SCENE2" and press the [RIGHT] or [LEFT ]

button to select "SCENE1" to resume normal operation.

Scene file

number

**ALC CONT**(1)

BACK LIGHT COMP

OFF

ABS

MASK SET

- +

LEVEL .I..... 0

RET TOP END

BLC ON

Andere Handbücher für WV-CP300 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Sicherheitskamera Handbücher

Panasonic

Panasonic KX-HNC200FX Bedienungsanleitung

Panasonic

Panasonic BB-HCM381CE Bedienungsanleitung

Panasonic

Panasonic BL-C1 Betriebsanleitung

Panasonic

Panasonic WV-SW355PJ Bedienungsanleitung

Panasonic

Panasonic WV-SW115 Bedienungsanleitung

Panasonic

Panasonic Super Dynamic III WV-NS202A Bedienungsanleitung

Panasonic

Panasonic BL-C30A - Wireless 802.11 b/g Network Camera Leitfaden

Panasonic

Panasonic WVCP230 - CCD 120V Bedienungsanleitung

Panasonic

Panasonic BL-C160 Bedienungsanleitung

Panasonic

Panasonic WV-CS400 Bedienungsanleitung

Panasonic

Panasonic BL-C230A Bedienungsanleitung

Panasonic

Panasonic WV-SW175 Bedienungsanleitung

Panasonic

Panasonic WV-NS202AE Bedienungsanleitung

Panasonic

Panasonic WVPS15 - CAMERA DRIVE UNIT Bedienungsanleitung

Panasonic

Panasonic AW-UE80KP Bedienungsanleitung

Panasonic

Panasonic WV-V1170 Bedienungsanleitung

Panasonic

Panasonic WV-CL924A Bedienungsanleitung

Panasonic

Panasonic BB-HCM403 Bedienungsanleitung

Panasonic

Panasonic WV-CP150E Bedienungsanleitung

Panasonic

Panasonic BB-HCM547A Betriebsanleitung

Panasonic

Panasonic AWHE50HN - HD INTEGRATED CAMERA Bedienungsanleitung

Panasonic

Panasonic BL-C10 Bedienungsanleitung

Panasonic

Panasonic WV-SFR311A Betriebsanleitung

Panasonic

Panasonic i-Pro WV-SP102 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung