Panasonic WVCP120 - COLOR CCTV CAMERA Bedienungsanleitung

Operating

Instructions

Color CCTV Camera

WV-CP120

Panasonic

delate attempting

please reac

onnoct or operate this product,

to instruction* completely

no a

/*\00 NOT OPEN /*\

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER SER-

VICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PER-

SONNEL.

aThe lightning flash with arrowhead

fW\ symbol, within an equilateral triangle, is

/M^\ intended to alert the user to the pres-

/\ence of uninsulated "dangerous volt-

/X\age" within the product's enclosure that

/^\may be of sufficient magnitude to con-

qa iqc= stitute arisk of electric shock to per-

The exclamation point within an equi-

lateral triangle is intended to alert the

/I\user to the presence of important oper-

/I\ating and maintenance (servicing)

/•\instructions in the literature accompa-

'*nying the appliance.

SA 1966

WARNING:

TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO

For U.S.A-n

Warning:

This equipment generates and uses radio frequency energy '

and if not installed and used properly, i.e., in strict accor- j

dance with the instruction manual, may cause harmful ]

interference to radio communications. It has been tested |

and found to comply with the limits for aClass Acomputing |

device pursuant to Subpart Jof Part 15 of FCC Rules, !

which are designed to provide reasonable protection !

against such interference when operated in acommercial j

environment.

The serial number of this product may be found on the top

of the unit.

You should note the serial number of this unit in the space

provided and retain this book as apermanent record of your

purchase to aid identification in the event of theft.

Model No.

Serial No.

NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CONTENTS

PREFACE 2

FEATURES 2

PRECAUTIONS 3

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS 4

CAMERA SETUP 7

CONNECTIONS 8

LENSES 9

FOCUS ADJUSTMENT 15

INSTALLATION OF CAMERA 15

*INSTALLING PROCEDURE 16

DIMENSION OF MOUNTING BRACKET 17

PREVENTION OF BLOOMING AND SMEAR 18

SPECIFICATIONS 19

STANDARD ACCESSORIES 20

OPTIONAL ACCESSORIES 20

-1-

PREFACE

The Panasonic WV-CP120 offers anew low end color

camera through the use of a1/3 inch interline transfer

CCD image sensor

Asingle coaxial cable connects the camera and speci-

fied monitor or camera drive unit, and carries four sig-

nals audio, video DC power and vertical drive pulses

This simple system is specially designed for surveil-

lance and security needs at offices, factories, schools,

hospitals public or residential buildings, etc

FEATURES

•Minimum illumination of 05Ix at FO 75 (equivalent

15Ix at F1 4) and signal-to-noise ratio of 46 dB by

a1/3 inch interline transfer CCD image sensor with

512(H)X492 (V) pixels

•Horizontal resolution of 330 lines

•Adjustable video level by auto light control (ALC)

and electronic light control (ELC)

•Built-in automatic gam control (AGC +15dB) and

automatic tracing white balance control (ATW)

•Backlight compensation (BLC) function for shoot-

ing objects when there is interference by back-

ground lighting

•Optional C-mount lens can be used together with

the WV-AD20 optional lens mount converter

PRECAUTIONS

•Do not attempt to disassemble the camera.

To prevent electric shock, do not remove screws

or cover. There are no user-serviceable parts

inside.

Call aqualified service person for repairs.

•Handle the camera with care.

Do not abuse the camera. Avoid striking or shak-

ing it. The camera could be damaged by improper

handling or storage.

•Do not expose the camera to rain or moisture,

or try to operate it in wet areas.

Do take immediate action if the camera becomes

wet. Turn power off and call aqualified service

person. Moisture can damage the camera and

also cause electric shock.

Never direct the camera toward the sun.

Whether the camera is in use or not, never direct it

toward the sun, Do use caution when operating

the camera in the vicinity of spotlights or other

bright lights and light reflecting objects.

Do not operate the camera beyond its tempera-

ture or humidity range.

Do not use the camera in an environment of high

temperature or humidity. Use the camera under

ambient conditions of -10°C -+50°C (14°F -

122°F) in temperature and 90% or less in humidity.

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

ft—

u--.-i.jl i—

1" <n" ii

1(C5)(Oi "©

©rcopfi

ALC

SOFT

OFF

rj elc

ISHARP'

fj BLCON @>

[J MICON-^_^

-A-

(D Lens (Option)

See pages 9, 10, 11, 12 and 13for details on lens

selection. Astandard C-mount lens can be used

with the camera by adding the optional lens mount

converter (C-mount adapter) WV-AD20.

©Flange-back Adjusting Ring

This ring is used to adjust the back focal length or

picture focus by rotating it.

(D Video Output jack (VIDEO OUT)

This jack is used to adjust the angular field of view

or focus while observing the picture on the moni-

tor.

©Camera Mounting Screw Hole

This screw hole (1/4" -20) is used to mount the

camera onto amounting bracket or atripod.

(D Auto Iris Lens Connector

This 4-pin connector supplies power and the DC

control signal to the auto iris lens.

©Volume Control (VOLUME, MIN/MAX)

The volume control is preset to center position at

the factory. Adjust it to prevent howling.

(7) Video level Control (VIDEO LEVEL, L/H)

This control adjusts the level of auto iris control

when the ALC/ELC Switchi ©is set to ALC posi-

tion, or the level of electronic light control when the

ALC/ELC switch is set to ELC position.

®ATW Balance Control (ATW BALANCE, R/B)

This control adjusts the red and blue color bal-

ance. It is preset to center position which usually

provides accurate color reproduction.

(9) Power Indicator

#Camera Output Connector

This connector is used to connect acoaxial cable

to the CAMERA INPUT of the specified monitor or

camera drive unit, to receive DC power and verti-

cal drive pulse, and supply the audio and video

output of the camera.

©ALC/ELC Switch (ALC/ELC)

This switch is used to choose the lens as follows.

ALC: Choose this position when using an auto iris

lens.

ELC: Choose this position when using afixed or

manual iris lens.

<g> Detail level Switch (SOFT/SHARP)

The detail/aperture level can be chosen by this

switch. Choose the desired position while observ-

ing the picture on the monitor.

Note: Usually choose SHARP position. When a

Quad System is connected to this camera, set

this switch to SOFT position.

©BLC ON/OFF Switch (BLC, ON/OFF)

When backlight affects the picture, set this switch

to ON position for aclearer picture.

®Microphone Switch (MIC, ON/OFF)

Set this switch to ON or OFF as needed.

ELC (Electronic Light Control) Function

In this mode acontinuously variable electronic shutter

is employed to automatically control the exposure

times in the CCD Image Sensor according to the

incoming light level.

Cautions:

1. Under bright conditions such as outdoors, use an

ALC type lens as the ELC control range is not wide

enough under such conditions.

2. Under certain unique lighting conditions, the fol-

lowing may appear

•Strong smear and/or blooming on highlight objects

such as spot lights or windows.

•Noticeable flicker in the picture and/or color rendi-

tion variations.

•Periodic variance of white balance

Should these phenomena occur, use an ALC lens.

3. When shooting in the ELC mode with afixed iris

lens, the depth of field of the image may be less

than that obtained with an ALC lens. Depth of field

varies inversely with the iris opening.

Thus, using the camera in the ELC mode with the

fixed iris lens fully opened will result in less depth

of field than if an ALC lens were used. (In addition,

distant objects in the picture might not be in

focus.)

BLC (Backlight Compensation) Function CAMERA SETUP

When strong, unwanted background lighting interferes

with the clarity of important scene objects, turn this

switch to 'ON' position

Cautions

1Setting this switch to "BLC OFF" position is recom-

mended when using the pan/tilt head or when the

illumination of the object changes rapidly, since

the Lens ins speed is slowed in 'BLC ON" posi-

tion

2If the desired objects are not in the center of the

picture, backlight compensation may not work

effectively

Remove the rear cover fixing screw and pull the rear

cover out as shown below

To improve perfomance, select the function switches

located on the back

-7-

CONNECTION

Caution: Keep the POWER switch of the specified

monitor, Camera Extension Unit and Camera Drive

Unit in OFF position white making connections. If

the power of these units is ON during connections,

the camera does not function due to the built-in

protection circuit which protects it against wrong

connections.

•Basic System

Connect the coaxial cables between the camera

and CAMERA IN connector of the specified moni-

tor or Camera Drive Unit. The approximate maxi-

mum cable length is as follows:

Coaxial Maximum DC R/1 000 ft. of

Cable Type Cable Lenth Inner Conductor

RG-59/U 200 m(660 ft) Less than 30 Q

RG-6/U 500 m(1,650 ft) Less than 12 Q

The maximum DC resistance between the camera

and these unit is 20 Q.

Color Monitor WV-CM143

Color Video

Monitor

Camera Drive Unit

WV-PS11B

Andere Handbücher für WVCP120 - COLOR CCTV CAMERA

Inhaltsverzeichnis

Andere Panasonic Sicherheitskamera Handbücher

Panasonic

Panasonic WVCP474 - COLOR CCTV CAMERAS Bedienungsanleitung

Panasonic

Panasonic WVCF420 - CCTV Bedienungsanleitung

Panasonic

Panasonic Machine Vision GP-MF130 Bedienungsanleitung

Panasonic

Panasonic WV-CW970 Bedienungsanleitung

Panasonic

Panasonic GPMF622 - MACHINE VISION CAMER Bedienungsanleitung

Panasonic

Panasonic AWHE60H Bedienungsanleitung

Panasonic

Panasonic WV-CW594A Bedienungsanleitung

Panasonic

Panasonic WV-CP240EX Series Bedienungsanleitung

Panasonic

Panasonic WV-CP280 Series Bedienungsanleitung

Panasonic

Panasonic WV-CP630 Bedienungsanleitung

Panasonic

Panasonic GP-KR521 Bedienungsanleitung

Panasonic

Panasonic WV-SW559 Bedienungsanleitung

Panasonic

Panasonic WV-SW559 Bedienungsanleitung

Panasonic

Panasonic Super Dynamic III WV-CW964 Bedienungsanleitung

Panasonic

Panasonic BL-C30 Bedienungsanleitung

Panasonic

Panasonic BL-C210 Series Bedienungsanleitung

Panasonic

Panasonic WV-NP502 Bedienungsanleitung

Panasonic

Panasonic WV-CF504 Bedienungsanleitung

Panasonic

Panasonic KX-HNC600AZ Bedienungsanleitung

Panasonic

Panasonic AW-HE38HWP Bedienungsanleitung

Panasonic

Panasonic WV-SC384 Bedienungsanleitung

Panasonic

Panasonic i-pro WV-NP1004 Bedienungsanleitung

Panasonic

Panasonic WV-NF284E Bedienungsanleitung

Panasonic

Panasonic GP-US522HB Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung