Panasonic EBL128 Bedienungsanleitung

Operating Instructions

MEW01623

Revision -

Fire Alarm System EBL128

V2.0.x

Author: Jan Pettersson

Date of issue: 2013-10-09

Date of rev:

This page has deliberately been left blank.

Panasonic Eco Solutions Nordic AB

MEW01623 Rev: - EBL128 Operating Instructions V2.0.x

Table of contents

1Introduction________________________________ 7

2Definitions / Explanations ____________________ 9

2.1 PESN AB ________________________________________ 9

2.2 Alarm point _______________________________________ 9

2.2.1 Smoke detector ________________________________ 9

2.2.2 Sensor _______________________________________ 9

2.2.3 Analog detector________________________________ 9

2.2.4 (Analog) Sensor Base (ASB) _____________________ 9

2.2.5 Conventional detector ___________________________ 9

2.2.6 Conventional Detector Base (CDB) ________________ 9

2.2.7 Addressable___________________________________ 9

2.2.8 Old detector__________________________________ 10

2.2.9 Conventional zone line _________________________ 10

2.2.10 Addressable zone interface ______________________ 10

2.3 Output unit ______________________________________ 10

2.4 Output / Control output_____________________________ 10

2.5 Short circuit isolator _______________________________ 10

2.6 Display unit (D.U.) ________________________________ 10

2.7 COM loop _______________________________________ 10

2.8 Control Unit (C.U.) / C.I.E.__________________________ 10

2.9 Fire Brigade Panel (FBP) ___________________________ 10

2.10 Control panel (CP) ________________________________ 11

2.11 LED____________________________________________ 11

2.12 External Indicator (LED) ___________________________ 11

2.13 Display / LCD____________________________________ 11

2.14 Door open / Key switch_____________________________ 11

2.15 Site Specific Data (SSD)____________________________ 11

2.16 Software (S/W) / Firmware / System program ___________ 11

2.17 EBLWin ________________________________________ 11

2.18 Web-server ______________________________________ 11

3Overview _________________________________ 12

3.1 The EBL128 c.i.e. _________________________________ 12

3.2 S/W versions _____________________________________ 12

3.3 Documents ______________________________________ 12

3.4 Applications _____________________________________ 12

3.5 PC S/W _________________________________________ 12

4Control & Indicating Equipment _____________ 14

5LED indicators and push buttons _____________ 16

6Normal operation __________________________ 21

6.1 The display in EBL128 _____________________________ 21

6.1.1 LCD backlight________________________________ 21

Panasonic Eco Solutions Nordic AB

MEW01623 Rev: - EBL128 Operating Instructions V2.0.x

6.1.2 The LCD information priority order _______________ 21

7User level, User name & Password ____________ 23

7.1 User level 1 ______________________________________ 24

7.2 User level 2A_____________________________________ 24

7.3 User level 2B_____________________________________ 25

7.4 User level 2C_____________________________________ 26

7.5 User level 3A_____________________________________ 27

7.6 Access level 3B___________________________________ 27

7.7 Access level 4 ____________________________________ 27

8Silence Alarm devices_______________________ 29

8.1 Silence alarm devices (inside switch) __________________ 30

8.2 New Zealand FB Silence switch (outside switch)_________ 30

9Disable / Re-enable alarm devices_____________ 31

10 "Silence buzzer" ___________________________ 33

10.1 Buzzer __________________________________________ 33

11 Disable / Re-enable all control, extinguishing,

ventilation and interlocking outputs ________________ 34

12 Evacuate, Alert Annunciation Acknowledge and

Disable ________________________________________ 35

12.1 Evacuate ________________________________________ 35

12.2 Alert Annunciation Acknowledge_____________________ 35

12.3 Disable _________________________________________ 35

13 German functions / units ____________________ 36

13.1 Push-button "ÜE prüfen" ___________________________ 36

13.2 Button "Brandfall Steuerungen ab"____________________ 36

13.3 Indication "Brandfall Steuerungen ab" _________________ 37

13.4 Button "Akustische Signale ab" ______________________ 37

13.5 Indication "Akustische Signale ab"____________________ 37

13.5.1 Indication in button "Akustische Signale ab" ________ 37

13.6 The buzzer in the c.i.e. _____________________________ 37

13.7 Button "ÜE ab" ___________________________________ 37

13.8 Indication "ÜE ab" ________________________________ 38

13.9 Disablements of outputs; Information in the c.i.e. and FAT

display respectively. _____________________________________ 38

14 Door open ________________________________ 39

14.1 LED "Door open" _________________________________ 39

14.2 Outputs for routing equipment (Fire brigade tx and Fault tx) 39

14.3 Silence buzzer ____________________________________ 39

15 Technical address / Presentation number ______ 40

15.1 Technical address for COM loop units _________________ 40

15.2 Presentation number _______________________________ 40

16 Alarm types _______________________________ 41

16.1 Pre-warning______________________________________ 41

Panasonic Eco Solutions Nordic AB

MEW01623 Rev: - EBL128 Operating Instructions V2.0.x

16.2 Fire alarm _______________________________________ 42

16.2.1 Fire alarm menu (X1-X9) _______________________ 45

16.2.2 Alert Annunciation alarm (AA alarm) _____________ 48

16.2.3 Co-incidence alarm (two-unit / -zone dependence) ___ 49

16.3 Heavy smoke alarm / Heavy heat alarm ________________ 49

16.4 Key cabinet alarm _________________________________ 50

16.4.1 Key cabinet opened before a fire alarm_____________ 50

16.4.2 Key cabinet opened in conjunction with a fire alarm __ 51

16.5 Quiet alarm ______________________________________ 51

16.6 Alarm Acknowledgement Facility (AAF)_______________ 51

17 Alarm reset _______________________________ 53

17.1 Pre-warning reset _________________________________ 53

17.2 Fire alarm reset ___________________________________ 53

17.2.1 All _________________________________________ 53

17.2.2 Single_______________________________________ 53

17.2.3 Single with automatic disablement ________________ 54

17.2.4 Co-incidence alarm ____________________________ 55

17.3 Heavy smoke / heat alarm reset ______________________ 55

17.4 Key cabinet alarm reset_____________________________ 55

17.5 Quiet alarm reset__________________________________ 55

17.6 Alarm Acknowledgement Facility (AAF) reset __________ 55

17.7 Acknowledged alarm ______________________________ 56

17.8 Isolated alarm ____________________________________ 56

18 Fault_____________________________________ 57

18.1 Fault messages ___________________________________ 58

18.2 Fault acknowledge ________________________________ 70

19 Commissioning an EBL128 __________________ 71

20 SSD programming & download ______________ 72

20.1 SSD programming_________________________________ 72

20.2 Auto generating SSD_______________________________ 72

20.3 SSD download____________________________________ 72

20.4 Download of Alarm texts ___________________________ 74

21 Software (S/W) download ___________________ 75

21.1 Download of S/W in EBL128 (c.i.e.) __________________ 75

21.2 Earlier S/W version download _______________________ 76

21.3 S/W download in Display Units ______________________ 76

22 Restart ___________________________________ 77

22.1 Boot menu_______________________________________ 79

23 Access____________________________________ 81

24 Perform monthly test (H1)___________________ 83

25 Disable or re-enable (H2)____________________ 85

25.1 Disable zone (H2/B1) ______________________________ 86

25.2 Disable zone / address (H2/B2)_______________________ 87

Panasonic Eco Solutions Nordic AB

MEW01623 Rev: - EBL128 Operating Instructions V2.0.x

25.3 Disable output (H2/B3)_____________________________ 88

25.4 Disable all control, ventilation, exting or interlocking outputs

(H2/B4) _______________________________________________ 90

25.5 Re-enable zone (H2/B5) ____________________________ 91

25.6 Re-enable zone / address (H2/B6)_____________________ 92

25.7 Re-enable output (H2/B7)___________________________ 93

25.8 Re-enable all control, ventil, exting or interlocking outputs

(H2/B8) _______________________________________________ 95

25.9 Disable / re-enable alarm devices (H2/B9)______________ 96

25.10 Disable / re-enable outputs for routing equipment (H2/B10)97

25.11 Disable / re-enable alert annunciation function (H2/B11) 98

26 Set calendar and clock (H3)__________________ 99

26.1 Daylight saving time______________________________ 100

27 Present system status (H4)__________________ 101

27.1 Disablement (H4/U1) _____________________________ 101

27.2 Disablement by time channel (H4/U2) ________________ 102

27.3 Sensor values (H4/U3) ____________________________ 103

27.3.1 Reset of a week average sensor value_____________ 106

27.4 Sensors activating SERVICE signal (H4/U4)___________ 107

27.5 Technical warning (H4/U5) ________________________ 108

27.6 Event log (H4/U6)________________________________ 109

27.7 Version and alarm counter (H4/U7) __________________ 110

28 Service (H5)______________________________ 111

28.1 Calibration of supervised outputs (H5/A1)_____________ 112

28.2 Sensitive fault detection mode (H5/A2) _______________ 114

28.3 Service mode for COM-loop (H5/A3) ________________ 115

28.4 Display current consumption in unit (H5/A4)___________ 117

28.5 Display current consumption on COM-loop (H5/A5) ____ 118

28.6 Display statistics for COM loop (H5/A6)______________ 119

28.7 Activate address setting mode for DU (H5/A7) _________ 120

28.8 Show information about Site Specific Data (H5/A8) _____ 121

29 FAULT Acknowledge (H6) _________________ 123

30 Perform ZONE TEST (test mode) (H7) _______ 124

31 Maintenance (H8) _________________________ 126

31.1 Disconnect / Re-connect COM loop (H8/S1) ___________ 126

31.2 Disconnect / Re-connect zone line input (H5/A2) _______ 127

31.3 Disconnect / Re-connect addressable zone interface input

(H5/S3) ______________________________________________ 128

31.4 Acknowledge SERVICE signal (H8/S4)_______________ 129

31.5 Restore weekly average to default (H8/S5)_____________ 130

31.6 Test of alarm devices (H8/S6)_______________________ 131

31.7 Safe shut down of control unit (H8/S7) _______________ 132

31.8 Activate zone-address in alarm mode (H8/S8) __________ 133

31.9 Activate output (H8/S9) ___________________________ 135

Panasonic Eco Solutions Nordic AB

MEW01623 Rev: - EBL128 Operating Instructions V2.0.x

31.10 Reset activated output (H8/S10) ___________________ 137

32 Interlocking outputs and inputs (H9) _________ 138

32.1 Activated interlocking outputs/inputs (H9/C1)__________ 138

32.2 Activate interlocking output (H9/C2) _________________ 139

32.3 Reset interlocking output (H9/C3) ___________________ 140

32.4 Disable interlocking output (H9/C4)__________________ 141

32.5 Re-enable interlocking output (H9/C5)________________ 142

33 Change password (H10)____________________ 143

34 Annual control ___________________________ 144

35 Battery maintenance_______________________ 145

36 How to avoid unnecessary (nuisance) fire alarms146

37 Revision history___________________________ 148

Panasonic Eco Solutions Nordic AB

MEW01623 Rev: - EBL128 Operating Instructions V2.0.x

This page has deliberately been left blank.

Panasonic Eco Solutions Nordic AB

MEW01623 Rev: - EBL128 Operating Instructions V2.0.x

1 Introduction

EBL128 Operating Instructions is a document

intended to be used

by the end-user and the fire brigade personnel as well as service /

commissioning engineers.

It could be read in conjunction with the EBL128 Planning

Instructions, since most of the information in one of the documents is

not found in the other document and vice versa.

It should also be read in conjunction with the EBL128 drawings

according to the valid Table of drawings.

Product Leaflets are also available at:

http://pesn.panasonic.se (Data sheets)

When planning a fire alarm installation the national regulations have

to be obeyed. A lot of detector types can be used. Detector coverage

area and detector placing in the room / building, etc. are matters for

the planning engineers and are not described in this document.

Due to continual development and improvement, different S/W

versions are to be found. This document is valid for the EBL128 S/W

version 2.0.x. On the date of this document is x=0.

EBL128 S/W version 2.0.x support and some functions require the

EBL128 main board 4556 with p.c.b. no. 9285-6A. This S/W version

also support main board with p.c.b. no. <9285-6A (e.g. 9285-5A).

EBL128 is produced for many countries, accordingly the look, the

texts, the functions, etc. might vary from country to country.

Products

Products consists of one or more parts (H/W) according to a Product

Parts List. A product has:

a type number (e.g. 4550)

an article number, often the same as the type no. but sometimes

a country code is added (e.g. 4550SE)

a product name (e.g. EBL128 Control & Indicating

Equipment, 128 addresses)

H/W

A H/W (e.g. a printed circuit board) has:

a type number (e.g. 4556)

an article number, often the same as the type no. but sometimes a

country code is added (e.g. 4556SE)

a product name (e.g. Main Board 255 addr.)

File name: L:\User documents\128\Doc\V2.0.x\MEW01623 (Rev -).doc

Dimensions & overviews, connection diagrams, etc.

Panasonic Eco Solutions Nordic AB

MEW01623 Rev: - EBL128 Operating Instructions V2.0.x

a p.c.b. number (e.g. 9285-6A) and can also have a configuration

(e.g. CFG: 1) and a revision (e.g. REV: 2)

sometimes is a S/W (software) downloaded.

S/W

A S/W has:

a version number (e.g. V2.0.0)

sometimes is additional information, such as Convention

(different functions / facilities), Language, etc. added.

PC S/W

A PC S/W is a program used for programming, commissioning, etc. It

has a version number.

Andere Handbücher für EBL128

Inhaltsverzeichnis

Andere Panasonic Sicherheitssystem Handbücher

Panasonic

Panasonic VIDEOLARM PCF5 Merkblatt

Panasonic

Panasonic KX-HNS101 Bedienungsanleitung

Panasonic

Panasonic External Presentation unit 1728 Stücklistenhandbuch

Panasonic

Panasonic Arbitrator-CP Bedienungsanleitung

Panasonic

Panasonic KX-HNS105 Bedienungsanleitung

Panasonic

Panasonic AW-HE100 Bedienungsanleitung

Panasonic

Panasonic 4414 Bedienungsanleitung

Panasonic

Panasonic WV-PB5564E Bedienungsanleitung

Panasonic

Panasonic BL-WV10 Bedienungsanleitung

Panasonic

Panasonic WVCP230 - CCD 120V Bedienungsanleitung

Panasonic

Panasonic PT56SX30B - 56" PROJECTION TV Bedienungsanleitung

Panasonic

Panasonic VL-GC001A Betriebsanleitung

Panasonic

Panasonic BL-WV10A Bedienungsanleitung

Panasonic

Panasonic WV-CW4C Bedienungsanleitung

Panasonic

Panasonic KX-HNS105AZ Bedienungsanleitung

Panasonic

Panasonic KX-HNB600 Technisches Datenblatt

Panasonic

Panasonic WV-ASC970 Bedienungsanleitung

Panasonic

Panasonic 4350 Bedienungsanleitung

Panasonic

Panasonic 1735 Stücklistenhandbuch

Panasonic

Panasonic WJ-ND300A/10000V Service-Handbuch

Panasonic

Panasonic WJ-HDE400 Bedienungsanleitung

Panasonic

Panasonic External Presentation unit 1728 Stücklistenhandbuch

Panasonic

Panasonic A02-ACAM3KIT Bedienungsanleitung

Panasonic

Panasonic WJ-ND400/1000 Service-Handbuch

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung