Panasonic KX-HNS105 Bedienungsanleitung

Installation Guide

Home Network System

Indoor Siren

Model No. KX-HNS105

Thank you for purchasing a Panasonic product.

This document explains how to install the indoor siren properly.

For details about how to use the system, refer to the User’s Guide

(page 12).

Please read this document before using the unit and save it for future

reference.

For assistance, please contact us at 1-800-272-7033 or visit our Web

site: www.panasonic.com/support for customers in the U.S.A. or

Puerto Rico.

Please register your product: www.panasonic.com/prodreg

Printed in China

HNS105_(en_en)_1120_ver.010.pdf 1 2014/11/19 20:18:28

Introduction

Accessory information ...............3

Important Information

About this system ......................4

For your safety ...........................4

Important safety instructions ......5

For best performance ................5

Other information .......................6

Setup

Part names and functions ..........7

About the LED indicator .............7

Setup overview ..........................7

Registering the siren ..................8

Confirming the usage area ........9

Wall mounting ..........................10

Note about power

connections .............................11

Appendix

Testing the siren ......................12

Adjusting the siren’s volume ....12

Features available when using the

[Home Network] app ................12

Accessing the User’s Guide ....12

Specifications ..........................12

FCC and other information ......14

Customer services ...................15

Warranty (For United States and

Puerto Rico) .............................16

Table of Contents

HNS105_(en_en)_1120_ver.010.pdf 2 2014/11/19 20:18:28

Accessory information

Supplied accessories

No. Accessory item/Part number Quantity

AAC adaptor/PNLV2360Z 1

BWall mounting screws (25 mm (1 inch))/XTB4+25AVW 2

A B

Other information

RDesign and specifications are subject to change without notice.

RThe illustrations in these instructions may vary slightly from the actual product.

Trademarks

RiPhone and iPad are registered trademarks of Apple Inc.

RAndroid is a trademark of Google Inc.

For assistance, please visit www.panasonic.com/support 3

Introduction

HNS105_(en_en)_1120_ver.010.pdf 3 2014/11/19 20:18:28

About this system

This system is an auxiliary system; it is

not designed to provide complete

protection from property loss.

Panasonic will not be held responsible

in the event that property loss occurs

while this system is in operation.

For your safety

To prevent severe injury and loss of life/

property, read this section carefully

before using the product to ensure

proper and safe operation of your

product.

WARNING

Power connection

RUse only the power source marked

on the product.

RDo not overload power outlets and

extension cords. This can result in

the risk of fire or electric shock.

RCompletely insert the AC adaptor/

power plug into the power outlet.

Failure to do so may cause electric

shock and/or excessive heat

resulting in a fire.

RRegularly remove any dust, etc.

from the AC adaptor/power plug by

pulling it from the power outlet, then

wiping with a dry cloth. Accumulated

dust may cause an insulation defect

from moisture, etc. resulting in a fire.

RUnplug the product from power

outlets if it emits smoke, an

abnormal smell, or makes an

unusual noise. These conditions can

cause fire or electric shock. Confirm

that smoke has stopped emitting

and contact us at

www.panasonic.com/contactinfo

RUnplug from power outlets and

never touch the inside of the product

if its casing has been broken open.

Danger of electric shock exists.

RNever touch the plug with wet

hands. Danger of electric shock

exists.

RDo not connect non-specified

devices.

Installation

RTo prevent the risk of fire or

electrical shock, do not expose the

product to rain or any type of

moisture.

RDo not place or use this product

near automatically controlled

devices such as automatic doors

and fire alarms. Radio waves

emitted from this product may cause

such devices to malfunction

resulting in an accident.

RDo not allow the AC adaptor to be

excessively pulled, bent or placed

under heavy objects.

RKeep small parts (screws, etc.) out

of the reach of children. There is a

risk of swallowing. In the event they

are swallowed, seek medical advice

immediately.

Operating safeguards

RUnplug the product from power

outlets before cleaning. Do not use

liquid or aerosol cleaners.

RDo not disassemble the product.

RNever put metal objects inside the

product. If metal objects enter the

product, turn off the circuit breaker

and contact an authorized service

center.

4For assistance, please visit www.panasonic.com/support

Important Information

HNS105_(en_en)_1120_ver.010.pdf 4 2014/11/19 20:18:28

Medical

RConsult the manufacturer of any

personal medical devices, such as

pacemakers or hearing aids, to

determine if they are adequately

shielded from external RF (radio

frequency) energy. DECT features

operate between 1.92 GHz and

1.93 GHz with a peak transmission

power of 115 mW.

RDo not use the product in health

care facilities if any regulations

posted in the area instruct you not to

do so. Hospitals or health care

facilities may be using equipment

that could be sensitive to external

RF energy.

CAUTION

Installation and location

RNever install wiring during a lightning

storm.

RThe AC adaptor is used as the main

disconnect device. Ensure that the

AC outlet is installed near the

product and is easily accessible.

RTo avoid the risk of strangulation,

keep the product and the AC

adaptor cord at least 1 m (3 feet)

from a child’s crib and out of the

reach of small children.

Preventing accidents and injuries

RDo not put your ear(s) near the

speaker, as loud sounds emitted

from the speaker may cause hearing

impairment.

RDo not look directly at the LED lights

when they are lit. Failure to do so

may cause damage to eyes.

Important safety

instructions

When using your product, basic safety

precautions should always be followed

to reduce the risk of fire, electric shock,

and injury to persons, including the

following:

1. Do not use this product near water

for example, near a bathtub,

washbowl, kitchen sink, or laundry

tub, in a wet basement or near a

swimming pool.

2. Use only the power cord indicated

in this document.

SAVE THESE INSTRUCTIONS

For best performance

Hub location/avoiding noise

The hub and other compatible

Panasonic devices use radio waves to

communicate with each other.

RFor maximum coverage and

noise-free communications, place

your hub:

– at a convenient, high, and central

location with no obstructions

between the product and hub in

an indoor environment.

– away from electronic appliances

such as TVs, radios, personal

computers, wireless devices, or

other phones.

– facing away from radio frequency

transmitters, such as external

antennas of mobile phone cell

stations. (Avoid putting the hub

on a bay window or near a

window.)

For assistance, please visit www.panasonic.com/support 5

Important Information

HNS105_(en_en)_1120_ver.010.pdf 5 2014/11/19 20:18:28

RIf the reception for a hub location is

not satisfactory, move the hub to

another location for better reception.

Environment

RKeep the product away from

electrical noise generating devices,

such as fluorescent lamps and

motors.

RThe product should be kept free

from excessive smoke, dust, high

temperature, and vibration.

RThe product should not be exposed

to direct sunlight.

RDo not place heavy objects on top of

the product.

RWhen you leave the product unused

for a long period of time, unplug the

product from the power outlet.

RThe product should be kept away

from heat sources such as heaters,

kitchen stoves, etc. It should not be

placed in rooms where the

temperature is less than 0 °C (32 °F)

or greater than 40 °C (104 °F).

Damp basements should also be

avoided.

ROperating the product near electrical

appliances may cause interference.

Move away from the electrical

appliances.

Other information

Routine care

RWipe the outer surface of the

product with a soft moist cloth.

RDo not use benzine, thinner, or any

abrasive powder.

Notice

6For assistance, please visit www.panasonic.com/support

Important Information

HNS105_(en_en)_1120_ver.010.pdf 6 2014/11/19 20:18:28

Part names and

functions

A B D E

Horn

Strobe light

Flashes when the siren is

sounding.

LED indicator

MHIGHN/MLOWN

Used to adjust the siren’s volume

(page 12).

Rear cover

M N

Used to confirm the status of the

siren or register the siren to the

hub.

About the LED

indicator

You can use the LED indicator to

confirm the siren’s status.

Indicator Status

Green, lit Normal operation

Red,

blinking

slowly

Siren is not registered

to a hub

Red,

blinking

Siren is out of range of

the hub

Red,

blinking

quickly

Alarm system was

triggered

Green,

blinking

Registration mode

(You pressed and held

MN)

Off No power

Setup overview

1Initial setup

Make sure you can access the

system using your mobile device.

For details, refer to the System

Setup Guide included with your

hub.

2Registration

Required only if the siren was

purchased separately (i.e., not as

part of a bundle).

3Confirm the installation area

Read the information in this

document to confirm that the

desired installation area is suitable

to proper operation.

4Installation

Install the siren in the desired

location.

For assistance, please visit www.panasonic.com/support 7

Setup

HNS105_(en_en)_1120_ver.010.pdf 7 2014/11/19 20:18:28

Registering the siren

This procedure is not required for

devices that were included as part of

a bundle.

Before you can use the siren, it must

be registered to the hub.

If you purchased devices separately

(i.e., not as part of a bundle), you must

You can register each device by using

the registration buttons or the [Home

Network] app.

Note:

RBefore registering the siren, make

sure the AC adaptors of the hub and

siren are connected and each

device is powered.

Using registration buttons

1Hub:

Press and hold M OTHER

DEVICEN until the LED indicator

blinks in green.

2Siren:

Press and hold MN until the

LED indicator blinks in green

(page 7).

RWhen registration is complete,

the hub sounds one long beep.

Note:

RTo cancel the registration, press

M N on the hub and on the siren.

RIf registration fails, the hub sounds

several short beeps.

Using the app

When you register the siren by using

the [Home Network] app, you can

assign a name to your devices and

group them by location. For more

information, refer to the User’s Guide

(page 12).

8For assistance, please visit www.panasonic.com/support

Setup

HNS105_(en_en)_1120_ver.010.pdf 8 2014/11/19 20:18:28

Confirming the

usage area

Wireless communication

range

The wireless communication range of

each device in the system from the hub

is approximately 50 m (160 feet)

indoors and approximately 300 m

(1,000 feet) outdoors. Wireless

communication may be unreliable

when the following obstacles are

located between the hub and other

devices.

RMetal doors or screens

RWalls containing aluminum-sheet

insulation

RWalls made of concrete or

corrugated iron

RDouble-pane glass windows

RMultiple walls

RWhen using each device on

separate floors or in different

buildings

Note:

RYou can use the siren’s LED

indicator to confirm the siren’s

communication status (page 7). If

the LED indicator is lit in green or is

blinking quickly in red, the siren is

communicating properly with the

hub.

Usage area cautions

Using the siren in the following areas

may cause deformation, malfunction, or

operational failure.

RIn direct sunlight

RAreas exposed to grease or steam,

such as kitchens

RNear fire or heating devices

RNear magnetic fields (such as near

microwaves and magnets)

RAreas subject to extreme

temperature changes, such as next

to air conditioners

RAreas with reflective objects, such

as glass, that can interfere with

detection of temperature variation

RAreas where the temperature is

affected by strong illuminating

objects (such as fluorescent lights)

RNear devices that emit strong radio

waves, such as mobile phones

For assistance, please visit www.panasonic.com/support 9

Setup

HNS105_(en_en)_1120_ver.010.pdf 9 2014/11/19 20:18:28

Wall mounting

To mount the siren flat against the wall,

use the rear cover.

Mounting examples*1 of the rear

cover

A Rear cover

*1 View of looking from above.

Note:

RThe strobe light flashes when the

siren sounds. Mount the siren in a

location where its strobe light will be

visible.

RMount the siren on the stable

location where the siren can be

adequately supported when

mounting.

RDo not mount siren on a soft

material. It may fall down, break or

cause injury.

RDo not mount the siren on the

following places: gypsum board,

ALC (autoclaved lightweight cellular

concrete), concrete block, plywood

less than 25.4 mm (1 inch) thick, etc.

Using the rear cover

1Remove the rear cover by

pressing the upper sides of the

cover (A) and sliding it down (B).

2Attach the rear cover to the wall by

using screws (

RPlace the rear cover with “UP”

mark facing upwards.

37 mm (1 15/32 inches)

10 For assistance, please visit www.panasonic.com/support

Setup

HNS105_(en_en)_1120_ver.010.pdf 10 2014/11/19 20:18:28

Andere Handbücher für KX-HNS105

Inhaltsverzeichnis

Andere Panasonic Sicherheitssystem Handbücher

Panasonic

Panasonic A02-ACAM3KIT Bedienungsanleitung

Panasonic

Panasonic KX-HNS105AZ Bedienungsanleitung

Panasonic

Panasonic External Presentation unit 1728 Stücklistenhandbuch

Panasonic

Panasonic WJ-ND300A/10000V Service-Handbuch

Panasonic

Panasonic 1735 Stücklistenhandbuch

Panasonic

Panasonic WV-CW4C Bedienungsanleitung

Panasonic

Panasonic WJ-NV200 Bedienungsanleitung

Panasonic

Panasonic BB-HGW700A - Network Camera Router Bedienungsanleitung

Panasonic

Panasonic WJ-HDE400 Bedienungsanleitung

Panasonic

Panasonic EBL128 Bedienungsanleitung

Panasonic

Panasonic WV-SC386 Bedienungsanleitung

Panasonic

Panasonic BL-WV10A Bedienungsanleitung

Panasonic

Panasonic 4414 Bedienungsanleitung

Panasonic

Panasonic WV-ASC970 Bedienungsanleitung

Panasonic

Panasonic WV-AS710 Bedienungsanleitung

Panasonic

Panasonic Fire Alarm Systems Heat Detectors 6275 Bedienungsanleitung

Panasonic

Panasonic WJ-ND400/1000 Service-Handbuch

Panasonic

Panasonic SF4B C Series Bedienungsanleitung

Panasonic

Panasonic KX-HGW600 Bedienungsanleitung

Panasonic

Panasonic BL-WV10 Bedienungsanleitung

Panasonic

Panasonic 2000 Bedienungsanleitung

Panasonic

Panasonic KX-HNB600 Technisches Datenblatt

Panasonic

Panasonic WVCP230 - CCD 120V Bedienungsanleitung

Panasonic

Panasonic External Presentation unit 1728 Stücklistenhandbuch

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung