Panduit CT-1090 Bedienungsanleitung

Page: 1 of 2

CONTROLLED CYCLE FERRULE CRIMPING TOOL

OPERATION, INSPECTION and MAINTENANCE INSTRUCTIONS

1. With the handles in the open position, insert the ferrule

into the crimp pocket. Make sure that the ferrule is

inserted fully into the crimp die (see Figure 2).

2. Insert the stripped wire into the ferrule until the wire

stops. efer to product packaging for wire strip length.

3. Crimp the ferrule by closing the handles until the

controlled cycle mechanism releases. Upon release,

the handles will open automatically and the crimped

ferrule can be removed.

NOTE: Crimp entire uninsulated ferrule length. This may

require additional crimps.

CT-1090 TOOL

Fig. 1

Fig. 2

Stripped

Wire

Crimp Die

Controlled cycle mechanism

prevents tool from opening

before crimp cycle is completed.

Manual release lever, push

forward in the event that

controlled cycle mechanism

must be released.

Cushioned handle grips

C IMP POCKETS for Ferrule

terminals. efer to product

packaging for wire range and

proper crimp pocket. Crimp

pockets are identified with

applicable wire range.

Ferrule - Wire

crimp section

Ferrule Insulated

section

CT-1090

PA28190A01

EV: 00 9-2016

E-mail:

[email protected]

For Technical Support:

1-800-777-3300

www.panduit.com

CAUTION:

Verify power is “OFF” before working on

wiring with these tools.

The plastic grips are for the user’s

comfort, and are not intended

to insulate against electrical shock while

working on li e electrical circuits.

INSPECTION / MAINTENANCE

NEW TOOLS -

BEFORE PLACING INTO SER ICE:

All Panduit crimping tools are inspected before they are

shipped from the factory. All new tools should be

inspected before being used.

New tools are shipped, factory lubricated, in protective

packaging. After inspection, simply clean any excess oil

from the crimping dies and place into service.

When the tool is not in use, keep the handles closed to

prevent objects from becoming lodged in the crimping

area. Store the tool in a clean, dry area.

Page: 2 of 2

IN SER ICE TOOLS - AFTER TOOLS HA E BEEN IN SER ICE:

It is recommended that each operator of the tool be made aware of - and responsible for following these maintenance

steps:

In-service tools should be cleaned and inspected at least ONCE A MONTH. To clean - wipe with a clean cloth.

In-service tools should be lubricated ONCE A WEEK, and after every cleaning. Lubricate all pins, pivots and bearing

surfaces with DOW CO NING®Molykote B 2 Plus.

Be sure to clean any excess oil from the crimping dies before using.

®Molykote B 2 Plus is the egistered Trademark of DOW CO NING.

ISUAL INSPECTION

1. Visually inspect the tool for missing or loose pins; then close the tool and note the return action of the handles.

2. Inspect the crimping dies for worn, chipped or broken edges.

3. If parts are missing, defective or damaged; contact Panduit for information on repair or replacement of tools.

4. Check for debris in dies. Any debris will need to be removed prior to tool use.

and MAINTENANCE INSTRUCTIONS CT-1090

Inhaltsverzeichnis

Andere Panduit Elektrowerkzeuge Handbücher

Panduit

Panduit CT-2930/L Bedienungsanleitung

Panduit

Panduit RT2HT Bedienungsanleitung

Panduit

Panduit GTH Bedienungsanleitung

Panduit

Panduit CP-881/E Bedienungsanleitung

Panduit

Panduit CT-2940 Series Bedienungsanleitung

Panduit

Panduit PBTMT Bedienungsanleitung

Panduit

Panduit CA-800EZ Bedienungsanleitung

Panduit

Panduit GS2B Bedienungsanleitung

Panduit

Panduit CT-260 Bedienungsanleitung

Panduit

Panduit BlackFin CT-2920 CCP Series Bedienungsanleitung

Panduit

Panduit CT-720 Bedienungsanleitung

Panduit

Panduit PN433 Bedienungsanleitung

Panduit

Panduit GTH Bedienungsanleitung

Panduit

Panduit BT2HT Bedienungsanleitung

Panduit

Panduit GS4EH Bedienungsanleitung

Panduit

Panduit CT-1700 Bedienungsanleitung

Panduit

Panduit CT-2980/L Bedienungsanleitung

Panduit

Panduit CT-400 Bedienungsanleitung

Panduit

Panduit ST-100 Bedienungsanleitung

Panduit

Panduit CP-991 Bedienungsanleitung

Panduit

Panduit CP-881 Bedienungsanleitung

Panduit

Panduit PDM Bedienungsanleitung

Panduit

Panduit CT-1701 Bedienungsanleitung

Panduit

Panduit ST2MT Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch