Paradox K32LCD+ Bedienungsanleitung

Printed in Canada | 06/2014 K32LCD+ Quick Install Guide

Technical Specifications

Warranty

Warranty: For complete warranty information on this product, please refer to the

Limited Warranty Statement found on the Web site www.paradox.com/terms. Your

use of the Paradox product signifies your acceptance of all warranty terms and

conditions.

notice. www.paradox.com

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

K32LCD+ Keypad

Quick Install Guide

The K32LCD+ keypad allows you to configure your Paradox

system through its interface.

Installation

1. Using a flathead screwdriver, pry the front housing assembly

from the backplate.

Figure 1: Opening the K32LCD+

Operating Voltage 9 to 16Vdc

Operating Temp. -10 to 55°C (14 to 131°F)

Power Consumption Maximum current - 150mA

Dimensions 15 x 12.6 x 2.7 cm (6 x 4.9 x 1.06 in.)

Weight 230g (8.1 oz)

Humidity 5-93%

Compatibility

Compatible with MG5000, MG5050, and Spectra

SP series V2.31 or higher and SP4000, SP65 V4.90

or higher.

Compliance EN50131-3 Grade 2; Environmental Class II

K32LCD+-EI00

K32LCD+ Quick Install Guide Printed in Canada | 06/2014

2. Mount the backplate to the wall by securing a M3.5 (#6)

screw in each of the dedicated mounting holes and tamper

hole. Ensure that the top is up, as shown in figure 2.

Figure 2: Backplate

3. Connect the 4-wire combus wires to the connector bus, as

shown in figure 3.

Figure 3: Wiring

4. Assemble both items by joining the hooks on the backplate

to their respected slots on the front housing assembly.

5. Secure the front housing to the backplate by snapping it

into place.

The installation process is now complete.

Configuration

To configure the modules through a keypad start by:

1. Press and hold the 0 (number zero) key.

NOTE:The area must be disarmed to configure it.

2. Initially you will see User Access Code but within 2 seconds

it will change to Installer Code.

3. When the Installer code appears, input the Installer code

number, the default number is [000000].

4. Input the 4 digit section code for Module Programming

[4003].

NOTE:You need module serial numbers for programming.

5. Input the Module serial number.

6. Input module sec [001].

7. Now you can start module programming.

Compatibility

The K32LCD+ is compatible with Magellan and Spectra series

control panels only. Please refer to the Technical Specifications

section for more details.

Wiring Slot

Wall Tamper

Top with hooks for

mounting keypad

panel

Mounting screw

holes

ZX1 is a:

Programmable

input

PGM is a:

Programmable

output

AllDisarmed

2014/19/0516:00

UserAccessCode

[*_]

InstallersCode

[_]

K32LCD+ Quick Install Guide Printed in Canada | 06/2014

2. Mount the backplate to the wall by securing a M3.5 (#6)

screw in each of the dedicated mounting holes and tamper

hole. Ensure that the top is up, as shown in figure 2.

Figure 2: Backplate

3. Connect the 4-wire combus wires to the connector bus, as

shown in figure 3.

Figure 3: Wiring

4. Assemble both items by joining the hooks on the backplate

to their respected slots on the front housing assembly.

5. Secure the front housing to the backplate by snapping it

into place.

The installation process is now complete.

Configuration

To configure the modules through a keypad start by:

1. Press and hold the 0 (number zero) key.

NOTE:The area must be disarmed to configure it.

2. Initially you will see User Access Code but within 2 seconds

it will change to Installer Code.

3. When the Installer code appears, input the Installer code

number, the default number is [000000].

4. Input the 4 digit section code for Module Programming

[4003].

NOTE:You need module serial numbers for programming.

5. Input the Module serial number.

6. Input module sec [001].

7. Now you can start module programming.

Compatibility

The K32LCD+ is compatible with Magellan and Spectra series

control panels only. Please refer to the Technical Specifications

section for more details.

Wiring Slot

Wall Tamper

Top with hooks for

mounting keypad

panel

Mounting screw

holes

ZX1 is a:

Programmable

input

PGM is a:

Programmable

output

AllDisarmed

2014/19/0516:00

UserAccessCode

[*_]

InstallersCode

[_]

Printed in Canada | 06/2014 K32LCD+ Quick Install Guide

Technical Specifications

Warranty

Warranty: For complete warranty information on this product, please refer to the

Limited Warranty Statement found on the Web site www.paradox.com/terms. Your

use of the Paradox product signifies your acceptance of all warranty terms and

conditions.

notice. www.paradox.com

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

K32LCD+ Keypad

Quick Install Guide

The K32LCD+ keypad allows you to configure your Paradox

system through its interface.

Installation

1. Using a flathead screwdriver, pry the front housing assembly

from the backplate.

Figure 1: Opening the K32LCD+

Operating Voltage 9 to 16Vdc

Operating Temp. -10 to 55°C (14 to 131°F)

Power Consumption Maximum current - 150mA

Dimensions 15 x 12.6 x 2.7 cm (6 x 4.9 x 1.06 in.)

Weight 230g (8.1 oz)

Humidity 5-93%

Compatibility

Compatible with MG5000, MG5050, and Spectra

SP series V2.31 or higher and SP4000, SP65 V4.90

or higher.

Compliance EN50131-3 Grade 2; Environmental Class II

K32LCD+-EI00

Andere Handbücher für K32LCD+

Inhaltsverzeichnis

Andere Paradox Tastenfeld Handbücher

Paradox

Paradox K32LCD+ Bedienungsanleitung

Paradox

Paradox Esprit Bedienungsanleitung

Paradox

Paradox K641 Bedienungsanleitung

Paradox

Paradox 1640 Bedienungsanleitung

Paradox

Paradox Digiplex DGP2-648 Bedienungsanleitung

Paradox

Paradox Digiplex DGP2-641 Bedienungsanleitung

Paradox

Paradox Esprit+ 642 Bedienungsanleitung

Paradox

Paradox K35 Bedienungsanleitung

Paradox

Paradox TM40 Bedienungsanleitung

Paradox

Paradox IMPERIAL V32 Bedienungsanleitung

Paradox

Paradox Paradox Digiplex DGP-610 Bedienungsanleitung

Paradox

Paradox Spectra 1641 Montageanleitung

Paradox

Paradox Esprit 616 Bedienungsanleitung

Paradox

Paradox 1686V Bedienungsanleitung

Paradox

Paradox Paradox Esprit 616LED Bedienungsanleitung

Paradox

Paradox SP5500 Bedienungsanleitung

Paradox

Paradox Crimewatch TM50 Bedienungsanleitung

Paradox

Paradox Digiplex DGP-641 Bedienungsanleitung

Paradox

Paradox Digiplex DGP2-648 Bedienungsanleitung

Paradox

Paradox REM3 Bedienungsanleitung

Paradox

Paradox Spectra 1689 Bedienungsanleitung

Paradox

Paradox Digiplex EVO DGP2-641BL Bedienungsanleitung

Paradox

Paradox Spectra 1689 Bedienungsanleitung

Paradox

Paradox TM50 Touch Bedienungsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung