Paradox Marine Magel 6130 Bedienungsanleitung

Installation Manual

Marine Magellan 6130/6160

Table of Content

Introduction……………………………….....2

Section 1: Installation Consideration…...2

Supply Voltage Considerations...........................2

Location Considerations…….…………...............3

Section 2: Mounting………………………..4

Marine Magellan……………………………..........4

Artion GSM Module…………………....................5

Artion Battery Backup...…………………………...5

Section 3: Electrical Installation…………7

AC Installations………………….…………………7

DC Installations……………...………………….....9

Internal Battery Backup / Marine Magellan…......9

Communication Lines…………………..….…..….9

Section 4: Programming…………………...12

1 –Language……………………………………..12

2 - User Profile……………………………………12

3 –Communicator………………………………..14

4 –Delays and Tones……………………………17

5 –System Test…………………………………..17

6 - Zone Profile: Overview…………………..…..18

Zone Definitions………………………..18

Zone Hardware Descriptions…………20

DCTXP2…………………..…….……...20

PMD-75 Motion Detector……………...22

SD-738 Smoke Detector………………23

Battery Low Voltage Detector………...23

High Water Alarm……………………...25

6 - Zone Profile: Programming…………...……..25

7 –Output Profile: Overview…………………….27

PGM Activation Events ……………….27

PGM Electrical Installation……………29

7 –Output Profile: Programming……………….29

8 –Keypad Profile Overview………………..…..31

8 - Keypad Profile Programming……….……....33

9 –Repeater Profile Overview………...………..33

9 - Repeater Profile Programming……..……….33

10 –Signal Strength………………………..........34

11 –Passwords…………………………..……....34

Console Trouble…………………………..……...35

AC Diagram……………………………………….37

DC Diagram……………………………………….38

PGM Wiring Examples………………………39 -42

Programming web…………………………...…...43

Marine Magellan Keypad Description…….…......4

id85386625 pdfMachine by Broadgun Software - a great PDF writer! - a great PDF creator! - http://www.pdfmachine.com http://www.broadgun.com

Introduction

Congratulations on your purchase of the Marine Magellan wireless security and

monitoring system for your yacht (Diagram 1). The system is designed to provide reliable

protection giving you true piece of mind when you are away from your vessel. This guide is

designed to walk the installer through the complete setup and basic wireless programming of the

Marine Magellan System. Please read the manual thoroughly before beginning. It is

recommended that the installer have a basic understanding of electrical fundamentals and

adheres to the ABYC standards of marine electronics.

Diagram 1

Section 1:

Installation Consideration

The placement of the individual

components of the Marine Magellan system

is very important. The installer must make

sure that adequate security concerns and

end user “ease of use”are taken into

account. Reference the following guidelines

before drilling any holes or running any

wires.

Supply Voltage

The Marine Magellan wireless security

and monitoring system must be installed in

an adequate and well thought out location

on your vessel. The system can be

powered from the vessels 110 AC (VAC)

supply and stepped down through our 16

VAC transformers. It can also be powered

by the vessels domestic battery banks 12

volts DC (VDC). It is important to establish

what voltage supply best suits your vessels

needs. Typically an AC power source is

used on all vessels that have a constant AC

source from shore power or a generator.

Powering the system through the vessels

battery banks is typically done on smaller

boats where AC power is not constant

Wire needs

-18 AWG / 2 conductor wire

Approximately 20 ft.

- Communication wire / 2 conductors

Telephone wire, Cat 5, or similar

approximately 12 ft.

AC installation

There must be a constant 110 VAC

source in the vicinity of the units for power.

The 16 VAC transformer must plug into the

110 VAC outlet. It is suggested that an

isolated outlet be installed strictly for the

plug in transformer(s). The 16 VAC output

feeds to the Marine Magellan head unit and

another transformer can feed to the Artion

Battery backup board. The Artion Battery

backup converts this 16 VAC to 12 VDC

while charging the battery backup for the

Artion. It is important that this AC source be

constantly powered when the boat is not

being used. It is suggested that you power

the system off of its own breaker.

DC installation

There must be a constant 12 Volt DC

(Direct Current) source in the vicinity of the

units for power. This 12 VDC must feed the

Marine Magellan and the Artion GSM

module directly. On DC installations the

Artion battery backup is not used.

Location Considerations

The Marine Magellan and the Artion

GSM Module must be mounted on the

interior of vessel. They should be

located as centrally as possible to all the

proposed zones. This area must be

clear from moisture and not susceptible

to drastic temperature changes.

There must be an adequate wire run

behind the Marine Magellan, Artion, and

the Artion Battery Backup Case (if

applicable) so wiring is not exposed.

Exposed wires compromise the systems

security as intruders could cut essential

communication lines. The installer must

properly research the proposed

locations of the devices so they have a

clear unobstructed wire run. The Marine

Magellan head unit and Artion unit

should be powered up and

communicating with no wire susceptible

to tampering.

The Artion should be as high as

possible on your vessel, mounted above

the water line for best cellular

communication, and located within 12 ft

of the Marine Magellan head unit. Use

the included 3 ft. extension cable to

extend the antenna and assist with the

clarity of the call.

It is important that the Artion be

accessible but not visible. This is

because in the event of an alarm, you

do not want the communication tool

exposed to any thieves. Possible

places include inside cabinets or behind

removable panels.

Section 2: Mounting

Once you have found an adequate

location for the Marine Magellan, Artion, and

the Artion Battery Backup Case (if

Applicable) according to the criteria on the

previous pages, it is time to mount them.

Marine Magellan

The Marine Magellan uses a plastic wall

plate for wall mounting (Diagram 2). If

mounting the unit on the wall you must first

pop out the rectangular cutout labeled D on

the plate to allow wiring access.

Diagram 2

The Marine Magellan can be mounted on a

wall by first securing the wall plate to the

wall and then mounting the console on the

secured wall plate.

1.) Place the wall plate on the desired spot

of the wall.

2.) Drill and insert screws into holes labeled

A as shown Diagram 2

3.) With the Rectangular cutout D removed

you must now drill a 5/8 inch hole into the

wall as to allow for wiring access from the

rear of the Marine Magellan.

Diagram 3

3. Place the console back plate flush against

the mounted wall

plate as shown in Diagram 3.

4. Slide the Marine Magellan’s open slots

labeled F (Diagram 3) onto the wall plate’s

tabs labeled B.

5. Gently apply downward pressure to insert

the wall plates

tabs into Marine Magellan’s open slots.

6. Once the Marine Magellan’s power and

communication wires are hooked up

(Electrical Installation, Page 8), Insert two

screws through the wall plate’s screw holes

labeled C and into holes labeled E (

Diagram 3 ) in the Marine Magellan back

plate. This will secure the console to the

wall.

Artion GSM Module

It is important that the GSM communication

module be mounted in such a location to

allow accessibility without obvious visibility.

Follow the steps below.

1.) Establish a proper location

2.) Mark the necessary holes to mount the

Artion and allow wiring access.

3.) Drill the mounting holes

4.) Drill the 5/8 wiring access hole

5.) Screw in the top two screws on the

left and right side of the area. Leave

approximately 1/8 inch between the wall

and the underside of the screw head.

6.) Feed your power, trigger and

communication wires through the wiring

hole.

7.) Place the GSM cellular module onto

the top two screws matching up the

respective holes and push downwards

to lock the unit into place.

8.) Depress the two tabs at the base of

the GSM cellular module and remove

the top Cover.

9.) Screw the final two screws on the

bottom of the GSM cellular module.

10.) Place cover back on Artion.

Artion Battery Backup

This case should be mounted in the vicinity

of the Artion. There are four screw holes

inside the metal case at all corners

(Diagram 5).

Diagram 4

Diagram 5

Section 3: Electrical Installation

* Power should be denied when

making all electrical connections.

Only apply power when all wire

connections have been doubled

checked for proper setup.

This section closely describes how to

power the essential components of the

system for both AC and DC installations. It

also shows how to hook up the Ring and Tip

communication wires between the Marine

Magellan Head unit and the Artion GSM

module. A basic final wiring setup for the

typical AC and DC installations can be

referenced on Appendage 1 and Appendage

2 respectively.

AC power setup

Marine Magellan

The AC plug in transformer supplies

voltage to both the Marine Magellan

Console and the battery backup supply.

The 110 VAC supply to the outlet should be

on its own breaker. If the installer must tap

into an existing outlet to get power, make

sure that the existing breaker is properly

current rated for the additional outlet. In

either case, the AC breaker must be left on

while away from boat.

Connect the two conductor wire to the

“AC”inputs of the Marine Magellan. On the

other end, connect the two wires to the

output screw terminals on the AC

transformer (Diagram 6). It is suggested

that you crimp on spade connectors to the

wire for a secure connection to the

transformer. Since the voltage source is

AC, the two connections are

interchangeable between the two inputs.

Battery Backup

The external battery backup case has

been designed to supply a constant 12 VDC

to the Artion GSM module. It simply takes

the 16 VAC input from the transformer,

inverts it to 12 VDC, and charges the

backup battery (Diagram 7). This device is

only used during AC installations.

Diagram 6

Diagram 7

DC power Setup

Marine Magellan

The Marine Magellan panel can easily

be powered from the vessels 12VDC

system. Simply get a constant voltage

source to the unit from the vessels battery

banks or domestic bus (Diagram 8). It is

suggested that the installer fuse protect the

Marine Magellan system by placing an in-

line 1 amp fuse on the Positive input wire

(not supplied).

Marine Magellan

Internal Battery Backup

The Marine Magellan uses its own

backup battery pack to provide power during

a power loss. This is not to be confused

with the Artion Battery Backup. A 7.2Vdc

1.8Ah NiMH (Nickel Metal Hydride)

rechargeable battery pack is included with

the Marine Magellan console. Connect as

shown in Diagram 9.

Artion GSM Module

The Artion GSM module simply needs a

constant 12 VDC to operate

(Diagram 10). In AC installations this power

comes from the battery backup case. In DC

installations, this power comes from the

primary domestic source.

Communication Lines

Marine Magellan to Artion

With the power establish for all the

devices, it is now time to hook up the

communication wire between the Marine

Magellan and the Artion GSM Module.

Simply connect the “Line Out”of the Artion

GSM module to the “Line In”of the Marine

Magellan. The “Line Out”of the Artion has a

tip “T”and ring “R”. The general rule when

hooking up this line is red goes to ring and

green goes to tip. There are two options for

connecting to the “Line in”of the Marine

Magellan. The first option is a line plug in

connection through an RJ-11 (Diagram 11).

The second option is a direct connection to

the “Ring”and “Tip”(Diagram 12).

Diagram 8

Diagram 9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Paradox Sicherheitssystem Handbücher

Paradox

Paradox Magellan MG5050E Bedienungsanleitung

Paradox

Paradox Magellan MG5075 Bedienungsanleitung

Paradox

Paradox SR120 Bedienungsanleitung

Paradox

Paradox Digiplex EVO48 V1.20 Bedienungsanleitung

Paradox

Paradox Digiplex EVO DGP2-640 Bedienungsanleitung

Paradox

Paradox Digiplex NE DGP-NE96 Betriebsanleitung

Paradox

Paradox IP100 Bedienungsanleitung

Paradox

Paradox MG5000 Bedienungsanleitung

Paradox

Paradox MG5050 Betriebsanleitung

Paradox

Paradox MG5000+ Bedienungsanleitung

Paradox

Paradox MG5000 Bedienungsanleitung

Paradox

Paradox PGM4 Bedienungsanleitung

Paradox

Paradox 1686V Bedienungsanleitung

Paradox

Paradox Magellan K636 Bedienungsanleitung

Paradox

Paradox Spectra Bedienungsanleitung

Paradox

Paradox ESPRIT 728 ULT Bedienungsanleitung

Paradox

Paradox Paradox Bedienungsanleitung

Paradox

Paradox SAFE PROTECTOR 950 Bedienungsanleitung

Paradox

Paradox MAGELLAN MG6250 Bedienungsanleitung

Paradox

Paradox Magellan MG5050 EN Bedienungsanleitung

Paradox

Paradox SR150 Bedienungsanleitung

Paradox

Paradox 950 Bedienungsanleitung

Paradox

Paradox Magellan MG-6060 Bedienungsanleitung

Paradox

Paradox Esprit 738 EXPRESS Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung