Park Scale Models AT-17 Bobcat Bedienungsanleitung
Park Scale Models
AT-17 Bobcat
Assembly Manual
Fuselage Construction
1. Glue the two ¼” balsa servo rails SR to BB5.
2. Assemble the wing mount block by gluing
WM1(x2), WM2 and WM3 together as shown.
3. Epoxy two of the supplied nylon nuts into the
wing mount block as shown. Be very careful not
to get any epoxy into the threads of the nut.
BB5
SR
5
WM3
WM2
WM1
4. Assemble the servo tray by gluing BB5 to BB7 as
shown. Ensure that BB5 is perpendicular to BB7.
5. Fit and glue the servo try assembly to BB3.
6. Fit and glue BB1 to BB3 Fit and glue the wing
mount block to BB3 and BB7.
7. Fit and glue BB2 to BB1, BB5, BB& and the wing
mount block.
BB5
BB7
BB3
BB1
Wing mount
block
BB2
8. Fit and glue BB4 to BB2 & BB3. Fit and glue BB6 to
BB2, BB3, BB5 and the wing mount block. It is
recommended to install your rudder and elevator
servos into the servo tray at this time.
9. Fit and glue FL7A (x2) to F3.
10. Fit and glue F2 to FL7A.
11. Fit and glue FL4(x2), FL5(x2) and FL6(x2) to F2 &
F3.
BB6
BB4
FL7A
F3
F2
FL4
FL5
FL6
12. Fit and glue FL10 into the center notches of F2 &
F3. Fit and glue FL9, FL8 and FL7 into the notches
in F2 & F3 on both sides of FL10.
13. Slide this assembly onto the wing mount/battery
box assembly as shown, do not glue in place!
14. Fit and glue FL1 into the center notch of F3,
unsure that the notch in FL1 is facing up. Fit and
glue FL2 and FL3 on both sides of FL1 as shown.
15. Fit and glue F1 to the wing mount/battery tray
assembly first. Carefully align and fit FL1-FL10 into
the notches in F1, ensure that they are fully
inserted into the notches and then glue in place.
Glue F2 and F3 to the wing mount/battery box
assembly.
FL10
FL9
FL8
FL7
FL1
FL2
FL3
F1
16. Assemble formers F4 and F5. Glue F6 to the motor
mount assembly. Fit and glue F4 and F5 into the
notches in the wing mount assembly. Glue F4 to
F3 and the wing mount assembly. Glue F5 to the
top of the wing mount assembly only!
See the end of the manual for how to assemble
the fuselage formers.
17. Assemble the fuselage sides as shown below. Fit
and glue the fuselage sides to F4-F6.
18. Fit formers F7-F9 into the fuselage sides.
19. Fit and glue F10 and F12A to the fuselage sides.
Ensure that the fuselage is straight before gluing
the formers F7-F9 in place.
20. Fit and glue F12 to F10 and the fuselage sides.
21. Fit and glue F11 to F12, F12A and the fuselage
sides.
22. Epoxy F11A to F11, F12A and the fuselage sides.
23. If you plan to install a steerable tail wheel it is
recommended to use a Dubro 1/2A steerable nose
wheel. Screw the mount to F11 using the pre-
drilled holes in F11. You will need to install the
control linkage to connect the tail wheel to the
rudder servo.
If you do not wish to install a steerable tail wheel,
a fixed tail wheel can be installed later.
24. Install the rudder and elevator pushrod sleeves.
Use Dubro Lazer Pushrods or similar.
25. Fit and glue F12B in place.
26. Fit and glue FS4 to F6-F10. Glue two pieces of
3/16” sq. balsa sticks into the notches in the
bottom of F6-F10 and also to the fuselage sides.
27. Glue two pieces of 3/16” sq. balsa sticks into the
notches in the top of F4-F10 and also to the
fuselage sides.
FS4
28. Fit and glue FS1A to F4-F6. Fit and glue FS2A to F4-
F8. Fit and glue FS1B to F6-F10. Fit and glue FS2B
to F8-F10. Fit and glue FS3 to F4-F8.
cop
29. Glue SH2(x2) in place where indicated, lightly
dampen the outside surface to help bending if
necessary. Fit and glue SH1 in place.
30. Glue SH3(x2) in place where indicated, lightly
dampen the outside surface to help bending if
necessary.
31. Fit and glue B1-B16 in place. Start with B12 and
work forward to B1.
FS1
FS2
FS3
SH1
SH2
B1
B16
Wing Construction
1. Start the center wing section by fitting R1(x2) and
R2(x2) to WS1A and WS2A. Ensure that the ribs
are perpendicular to the spars before gluing.
2. Fit and glue WS3, WM5 and TE1 to ribs.
3. Cut two (2) 5” lengths of the supplied 3/16”
hardwood dowel. Insert the dowels into the wing
spars as shown and epoxy in place. Allow the
dowels to extend past WS3 by ¼”.
R1
R2
WS2A
WS1A
WM5
TE1
WS3
Inhaltsverzeichnis
Andere Park Scale Models Spielzeug Handbücher
Park Scale Models
Park Scale Models Mini Drake Bedienungsanleitung
Park Scale Models
Park Scale Models LoLo Bedienungsanleitung
Park Scale Models
Park Scale Models NS-TKAT Bedienungsanleitung
Park Scale Models
Park Scale Models Grumman HU-16 Albatross Bedienungsanleitung
Park Scale Models
Park Scale Models Cessna 182 Bedienungsanleitung
Park Scale Models
Park Scale Models Boeing 314 Bedienungsanleitung
