Parkside PAGG 4 A1 Bedienungsanleitung

CORDLESS ENGRAVING TOOL 4V / AKKU-GRAVIER-

GERÄT 4 V / GRAVEUR SANS FIL 4 V PAGG 4 A1

GRAVEUR SANS FIL 4 V

Traduction des instructions d’origine

AKKU-GRAVIERGERÄT 4V

Originalbetriebsanleitung

CORDLESS ENGRAVING

TOOL 4V

Translation of the original instructions

AKU GRAVÍROVACÍ

PŘÍSTROJ 4 V

Překlad originálního provozního návodu

ACCU-GRAVEERAPPARAAT 4 V

Vertaling van de originele gebruiksaanwijzing

AKUMULÁTOROVÁ

GRAVÍROVAČKA 4 V

Preklad originálneho návodu na obsluhu

AKUMULATOROWE URZĄDZE-

NIE DO GRAWEROWANIA 4 V

Tłumaczenie oryginalnej instrukcji obsługi

APARATO GRABADOR

RECARGABLE 4 V

Traducción del manual de instrucciones original

BATTERIDREVET

GRAVERINGSVÆRKTØJ 4 V

Oversættelse af den originale driftsvejledning

IAN 359506_2101

GB Translation of the original instructions Page 1

DE Originalbetriebsanleitung Seite 23

FR Traduction des instructions d’origine Page 49

NL Vertaling van de originele gebruiksaanwijzing Pagina 79

CZ Překlad originálního provozního návodu Strana 103

PL Tłumaczenie oryginalnej instrukcji obsługi Strona 127

SK Preklad originálneho návodu na obsluhu Strana 153

ES Traducción del manual de instrucciones original Página 175

DK Oversættelse af den originale driftsvejledning Side 201

PAGG 4 A1 GB│IE │ 1 ■

Contents

Introduction...................................2

Intended use..........................................2

Notes on trademarks ...................................2

Features .............................................3

Package contents ......................................3

Technical speciﬁcations .................................4

General power tool safety warnings ..............6

1. Work area safety....................................6

2. Electrical safety .....................................6

3. Personal safety......................................7

4. Power tool use and care ..............................8

5. Battery tool use and care..............................9

6. Service ...........................................10

Safety guidelines for battery chargers .....................11

Before use ...................................12

Charging the appliance battery ..........................12

Battery level display ..................................13

Operation ...................................13

Switching on and oﬀ ..................................13

Setting the penetration depth of the engraving ..............13

Changing the engraving tip .............................14

Working procedures...................................14

Maintenance and cleaning......................15

Disposal.....................................15

Kompernass Handels GmbH warranty ...........17

Service ......................................20

Importer ....................................21

Translation of the original Conformity Declaration ..21

PAGG 4 A1

■ 2 │ GB│IE

CORDLESS ENGRAVING TOOL 4V

PAGG 4 A1

Introduction

Congratulations on the purchase of your new appliance.

You have chosen a high-quality product. The operating

instructions are part of this product. They contain important

information about safety, usage and disposal. Before using the

product, please familiarise yourself with all of the operating and

safety instructions. Use the product only as described and for the

range of applications speciﬁed. Please also pass these operating

instructions on to any future owner.

Intended use

This appliance is intended for engraving or decorating materials

such as metal, plastic, glass, ceramics, leather and stone. Any other

usage or modiﬁcation of the appliance is deemed to be improper

and carries a signiﬁcant risk of accidents. The manufacturer accepts

no responsibility for damage(s) attributable to misuse. This appliance

is not intended for commercial use.

Notes on trademarks

USB® is a registered trademark of USB Implementers Forum, Inc.

All other names and products may be trademarks or registered

trademarks of their respective owner.

PAGG 4 A1 GB│IE │ 3 ■

Features

1ON/OFF switch

2Battery capacity/charge level indicator

33x indicator LEDs (2 stroke rate levels per LED)

4+/–speed control buttons (stroke rate)

5Micro-USB-C socket

6Mains adapter*

7USB plug of the charger cable

8Charging cable

9Micro-USB-C plug of the charging cable

0Engraving tip lock

qEngraving tip

wEngraving templates

Package contents

1 cordless engraving tool 4V PAGG 4 A1

1 charging cable

5 engraving templates

1 set of operating instructions

PAGG 4 A1

■ 4 │ GB│IE

Technical speciﬁcations

Cordless engraving tool PAGG 4 A1

Nominal battery voltage 4 V (DC)

Cells 1

Battery (integrated) LITHIUM ion

Battery capacity 1500 mAh

6 stroke rate levels

Stroke rate n06000–19000 rpm

Charger PAGG 4 A1-1*

INPUT

Rated voltage 100–240 V ∼,

50–60 Hz (AC)

Rated power 16 W

OUTPUT

Rated voltage 5 V (DC)

Charging current 1.7 A

Charging time approx. 1 hr

Protection class II/ (double insulation)

* CHARGER NOT INCLUDED

PAGG 4 A1 GB│IE │ 5 ■

Noise emission value

Noise measurement value determined in accordance with

EN62841. The A-rated noise level of the power tool is typically

as follows:

Sound pressure level LpA = 82.6 dB (A)

Uncertainty KpA = 3 dB

Sound power level LWA = 93.6 dB (A)

Uncertainty KWA= 3 dB

Wear ear muﬀs!

Total vibration value ah= 2.8 m/s2

Uncertainty K = 1.5 m/s2

NOTE

► The vibration emission values and the noise emission values

given in these instructions have been measured in accordance

with a standardised test procedure and can be used for

comparison of the power tool with another tool.

► The speciﬁed total vibration values and the noise emission

values can also be used to make a provisional load estimate.

WARNING!

► Depending on the manner in which the power tool is being

used, and in particular the kind of workpiece that is being

worked, the vibration and noise emission values can deviate

from the values given in these instructions during actual use of

the power tool.

► Try to keep the load as low as possible. Measures to reduce

the vibration load are, e.g. wearing gloves and limiting the

working time. Wherein all states of operation must be included

(e.g. times when the power tool is switched oﬀ and times where

the power tool is switched on but running without load).

PAGG 4 A1

■ 6 │ GB│IE

General power tool safety

warnings

WARNING!

►Read all safety warnings, instructions, illustrations and speci-

ﬁcations provided with this power tool. Failure to follow all

instructions listed below may result in electric shock, ﬁre and/or

serious injury.

Save all warnings and instructions for future reference.

The term „power tool“ in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres, such as

in the presence of ﬂammable liquids, gases or dust. Power

tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power

tool. Distractions can cause you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug

in any way. Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such

as pipes, radiators, ranges and refrigerators. There is an

increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

PAGG 4 A1 GB│IE │ 7 ■

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away from

heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord

suitable for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a residual current device (RCD) protected supply. Use of

an RCD reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use a power tool while

you are tired or under the inﬂuence of drugs, alcohol or medi-

cation. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always wear eye protec-

tion.

Protective equipment such as a dust mask, non-skid safety

shoes, hard hat or hearing protection used for appropriate condi-

tions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the oﬀ-po-

sition before connecting to power source and/or battery pack,

picking up or carrying the tool. Carrying power tools with your

ﬁnger on the switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power

tool on. A wrench or a key left attached to a rotating part of the

power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all

times. This enables better control of the power tool in unexpected

situations.

Andere Handbücher für PAGG 4 A1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Parkside Werkzeuge Handbücher

Parkside

Parkside PFRS 1.5 B3 Bedienungsanleitung

Parkside

Parkside 73785 Bedienungsanleitung

Parkside

Parkside PDMH 4500 A3 Bedienungsanleitung

Parkside

Parkside PGG 15 A1 Bedienungsanleitung

Parkside

Parkside PMFAP 20-Li A1 Bedienungsanleitung

Parkside

Parkside PDT 40 D3 Bedienungsanleitung

Parkside

Parkside PDMH 4500 A2 Kurzanleitung

Parkside

Parkside PSVH 56 A1 Bedienungsanleitung

Parkside

Parkside PDST 10 A2 Bedienungsanleitung

Parkside

Parkside 100129 Bedienungsanleitung

Parkside

Parkside 89565 Bedienungsanleitung

Parkside

Parkside 73782 Bedienungsanleitung

Parkside

Parkside PSS 65 A1 Bedienungsanleitung

Parkside

Parkside PFE 50 A1 Bedienungsanleitung

Parkside

Parkside PDSP 1000 A1 SANDBLASTER GUN Bedienungsanleitung

Parkside

Parkside PDT 40 C2 Bedienungsanleitung

Parkside

Parkside PDSS A1 Bedienungsanleitung

Parkside

Parkside PDST 10 A1 Bedienungsanleitung

Parkside

Parkside PDSS A1 Bedienungsanleitung

Parkside

Parkside PSS 65 C1 Bedienungs- und Montageanleitung

Parkside

Parkside PVL 1 A1 Bedienungsanleitung

Parkside

Parkside PKGA 20-Li B1 Bedienungsanleitung

Parkside

Parkside PDSS 13 D4 Bedienungsanleitung

Parkside

Parkside PAMFW 12 C3 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung