Paslode CF325XP Bedienungsanleitung

Model CF325XP

2015

Part No. 905600

905625-1

9/15

It is the customerʼs responsibility to have

all operators and service personnel read

and understand this manual.

Model B20543P

Part No.

905700

Model CF325IM

Part No.

905800

Introduction

Paslode Cordless Framing Nailer

Operating Manual

1. READ THE MANUAL FROM COVER TO COVER

BEFORE USING THE TOOL.

2. FOLLOW ALL INSTRUCTIONS IN THE MANUAL.

My Paslode representative is:

Name

Address

piZetatSytiC

Telephone Number

This manual is intended to acquaint you with the

Paslode Cordless Framing Nailer. Unlike other power

fastening tools, the Cordless Framing Nailer is powered

by an internal combustion linear motor. In simpler

terms, your Cordless Framing Nailer is powered by a

motor similar to the one that powers an automobile. The

Cordless Framing Nailer ignites a fuel and air mixture to

produce the energy to drive the motor, which in turn

drives the fastener. As you will see, the Cordless Fram-

ing Nailer is totally self-contained. It carries its own fuel

supply and battery, along with a supply of fasteners.

For ease of use, this manual is divided into sections

(see Contents). Each section of the manual is written

with you, the tool operator, in mind. We have left out all

of the technical terms so that you can readily under-

stand how to get the maximum performance from your

Cordless Framing Nailer, and how to avoid damaging

the tool or injuring yourself. But, to accomplish this, we

need you to do two things:

The Cordless Framing Nailer should be handled like other

power fastening tools that you use. Like most tools, when

used improperly it could result in injury. If you are going to

allow others to use the Cordless Framing Nailer,it is your

responsibility to make sure that they also read and comply

with the instructions in this manual before attempting to

operate the tool.

Should you have questions about the Cordless Framing

Nailer, or wish to obtain additional copies of this

manual,please contact your Paslode® representative. The

space below is provided so that you may record your

representative's name, address, and telephone number.

Contents

egaPtcejbuS

Introduction................................................................................ 2

An Overview of the Paslode Cordless Framing Nailer ...............4

Safety Instructions......................................................................5

Battery and Charging System ................................................... 8

Fuel Cell and Metering Valve .................................................. 10

.........13

Paslode Cordless Framing Nailer Operation........................... 14

Fasteners and Applications..................................................... 15

Servicing ................................................................................. 16

Troubleshooting ...................................................................... 18

Thebatterychargermeetsallsafetyrequirementsforpower

tools.

is a trademark

Power Nailers are made in the U.S.A.

Paslode®is a member of:

Preparing the Paslode Cordless Framing Nailer for Use

RBRC

Li-ion

USA

An Illinois Tool Works Co.

155 Harlem Avenue

Glenview, IL 60025

www.paslode.com

An Overview of the Paslode Cordless Framing Nailer

Description

The Paslode Cordless Framing Nailer

is a self-contained,

fully portable nailer that uses liquid hydrocarbon fuel to

power a unique linear drive internal combustion motor.

Aswithanyinternalcombustionmotor,thePaslodeCordless

Nailerwillrequireperiodic maintenancetokeepitoperating

at it's peak performance. The cleaning procedure booklet

will instruct you on the proper cleaning of your tool. If

additionalservicesarerequired,contactyourlocalPaslode

service provider.

Specifications

Dimensions: Weight (with battery) 7.2 pounds

Height 14-1/2 inches

Length 12 inches

Cycle Rate:

Intermittent Operation – 2 to 3 nails

per second

NOTE:Exceedingtheseratescouldcausetoolto

overheat,

resulting in loss of performance or damage to tool

components.

By using the Paslode Cordless Framing Nailer at its

recommended cycle rate, you will be able to drive several

thousand nails in a typical workday.

Fasteners: 30°paper tape collation

Minimum 2 inch x .113 diameter shank

Maximum 3-1/4 inch x .131 diameter shank

Magazine Capacity: 1 nail strip + 5 fasteners.

Battery : 7.4 volts DC - Provides enough energy to

driveapproximately9000fastenersonafull

charge.

Fuel Cell:

Orangequicklode™ fuel cartridge (1.32oz)

Liquid hydrocarbon - Provides enough fuel

to drive approximately 1200 fasteners.

Cover and Filter

Motor Housing

MOTOR ASSEMBLY

Adjustable

Work-Contacting

Element

Follower

Trigger

Channel magazine

HANDLE ASSEMBLY

Battery

Compartment

(Opposite Side)

Battery

Indicator Light (LED)

Fuel Cartridge Compartment

Utility

Hook

Toe Nailing Teeth

NOTE: Altitude Restriction

Paslode Cordless tools are powered by an internal

combustion engine and are effected by altitude. The

tool may lose power or not cycle consistantly at

elevationsof6000feetorgreater.

Safety Instructions

The following safety instructions have been included in this

booklet to provide you with basic information necessary for

safeoperationofthePaslodeCordlessFramingNailer.DO

NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU

HAVE READ AND UNDERSTAND ALL SAFETY

PRECAUTIONS AND MANUAL INSTRUCTIONS.

Inadditiontotheseinstructions,trainingmaybenecessary.

Contact your Paslode representative for additional

information.

WARNING

The Paslode Cordless

Framing Nailer is an

internal combustion

device. It produces hot

exhaust gases that may

ignite flammable

materials. Never use the

tool in a combustible

environment or in the

presence of combustible

materials, such as

flammable chemicals,

adhesives, gasoline, or

solvents.

WARNING

Never attempt to operate

this tool until you have

read and understood all

safety precautions and

manual instructions.

Failure to follow all safety

precautions instructions

may result in a permanent

loss of vision, serious per-

sonal or even fatal injury,

property damage and/or

tool damage.

WARNING

Neverexposeorstorethe

tool, fuel or battery at

temperaturesinexcessof

120°F (49°C). Fuel and/

or the battery may burst,

releasing flammable gas.

WARNING

Framing Nailer, fuel cart-

ridge, battery cell and bat-

terychargeroutof the reach

of children.

WARNING

Thistoolmustbeoperated

only in a well-ventilated

environment,because

the tool exhausts carbon

monoxidesimilartoagas

chainsaw or lawnmower.

Exposure to carbon

monoxide from use in

eclosedareas,maycause

dizziness, nausea, or

unconsciousness or

death.

ALWAYS keep the Cordless

Safety Instructions

WARNING

EYEandEARsafetygear

must be worn when

working with or in the

vicinity of the Paslode

Cordless Framing Nailer.

7. NEVER OPERATE THE TOOL WITH THE WORK

CONTACTINGELEMENTREMOVEDORDISABLED.

This device helps reduce the possibility of accidental

fastenerdischargebypreventingthetoolfromoperating

until it is completely against the work surface.

NEVER operate the tool if the work contacting element

is not working properly.

8. ALWAYSPOINTTHETOOLAWAYFROMYOURSELF

AND OTHERS WHEN CLEARING JAMS OR

REMOVING FASTENERS. REMOVE THE FUEL

CARTRIDGE AND BATTERY.

Pull the follower slightly back and push the release

lever.Tipthetoolnoseupslightlyandfastenersshould

slide out of the rear of the magazine. If fasteners are

jammed, refer to the appropriate servicing section of

this manual.

9. NEVER OPERATE THE CORDLESS FRAMING

NAILER IF PARTS ARE LOOSE, DAMAGED OR

MISSING.

10. NEVER DRIVE FASTENERS INTO KNOTS OR ON

TOP OF OTHER FASTENERS.

A fastener may ricochet and cause serious injury.

11. OPERATE THE TOOL ONLY ON THE WORKPIECE.

1. Eye protection must meet the requirements of ANSI

Standard Z87.1 and should have side shields for

increased protection. As an employer you are

responsible for enforcing the use of eye protection

equipment by the tool operator and all personnel in the

work area.

2. NEVER ASSUME THE TOOL IS EMPTY.

Never point the tool at yourself or anyone else.

3. NEVER ENGAGEIN"HORSEPLAY"WITHTHETOOL.

The Cordless Framing Nailer is not a toy – it is a tool.

Careless and improper use may result in a serious

accident.

4. NEVERCARRYTHETOOLWITHYOURFINGERON,

OR SQUEEZING, THE TRIGGER.

This practice may result in the accidental discharge of

a fastener.

5. NEVER OPERATE A MALFUNCTIONING TOOL.

Refer to the servicing or troubleshooting section of this

manualtocorrecttheproblem.Iftheproblemcannotbe

corrected, stop using the tool and report it to your

supervisor or Paslode representative.

6. DO NOT LOAD FASTENERS WITH THE TRIGGER

AND/ORWORKCONTACTINGELEMENTPRESSED

IN. A fastener may be accidentally discharged.

WARNING

The Cordless Framimg

Nailer must be operated

only when it is in contact

with the work surface.

When fastening thin

materials such as

plywood, be sure to

position the tool so that

the fastener is driven into

the underlying piece.

12. NEVER DRIVE FASTENERS INTO AREAS WITH

CONCEALED HAZARDS.

Always check the area behind the work surface for

electricalwiring,gaspipes,waterpipes,sewerdrainsor

other potential hazards.

14.ALLOWONLYQUALIFIEDPERSONNELTOOPERATE

THE CORDLESS FRAMING NAILER.

WARNING

Only persons who have

read and fully understand

all tool operation, safety

and maintenance

instructions should be

allowed to operate the tool.

15. PROPERLY STORE FUEL CELL.

16. ALWAYS STORE THE TOOL WITH THE FUEL

CARTRIDGE AND BATTERY REMOVED.

Store the fuel cartridge in the case with the Cordless

Framing Nailer.

17. KEEP THE TOOL CLEAN AND WELL MAINTAINED.

A clean tool is less likely to jam or malfunction.

18. KEEP YOUR HANDS CLEAR OF THE WORK AREA

SURFACE.

WARNING

Always store tool, fuel

cartridge and battery

where they will not be

exposedtoanopenflame,

sparks or temperatures

above 120°F (49°C).

WARNING

A fastener may exit at an

angle unexpectedly and

cause injury.

IMPORTANT SAFETY INSTRUCTIONS!

SAVETHESE INSTRUCTIONS!

DANGER

TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, CAREFULLY

FOLLOW THESE INSTRUCTIONS

CHARGING SYSTEM SAFETY

INSTRUCTIONS!

13. ALWAYSMAINTAINSECUREANDUNOBSTRUCTED

FOOTING WHEN ON LADDERS, PLATFORMS OR

OTHER HIGH LOCATIONS.

WARNING

Never over-reach, since

tool recoil may cause a

loss of balance. Always

be aware of edges and

drop-offs when nailing on

rooftops and other high

locations. Keep them in

full view.

Safety Instructions

For connection to a supply outside North

America, use an attachment plug adapter

of the proper configuration for the power

outlet, if needed.

Battery And Charging System

Charging Instructions:

NOTE

After charging, the red light will go out and the green

light will come on, indicating that the battery is fully

charged. The charger will keep the battery at full

charge until it is removed.

Charging Times:

First charge (new battery) 1.5hours

Discharged Battery

5 minutes to 1.5 hours

Charging Don'ts:

Never charge battery outdoors or in temperatures

below 40 F (5 C).

Never allow metal objects to come in contact with

battery terminals.

3. Never puncture or attempt to open battery case or

cells.

Never store battery where it will be subjected to

temperatures above 120 F (49 C).

5. Never incinerate battery.

Never use a defective battery charger, one that

overheats and/or smokes when plugged in.

7. Never immerse the battery or charger in water.

Battery disposal:

The Paslode batteries contain lithium and should be re-

cycled or disposed of properly.

You may contact your local recycling center for information

on where to return the spent battery or call 1-800-822-8837

for information on Li-ion battery recycling in your area.

WARNING

CHEMICAL/EXPLOSION

HAZARD

ReadALLinstructionsbefore

charging or using battery.

Failure to follow ALL

instructionsmayresultinfire,

severe burns, or release of

toxic materials.

Important Charging Notes:

The Paslode Cordless tool comes with a rechargeable

Lithium Ion (Li-ion) battery and its own charging system.

This charging system is the only one that will work with

Paslode Li-ion batteries. The first step in preparing a new

tool for operation is to fully charge the battery. New batter-

ies are shipped partially discharged and must be

charged prior to first use. Batteries will take 5 minutes to

1.5 hour (time will be dependant on the amount of discharge

within the battery) to recharge.

Remove the battery from tool or case and insert termi-

nals down into charger. The red light will come on

indicating that the battery is charging and the green light

will go out.

If battery is completely discharged the red light and

the green light may flash back and forth for up to 20

minutes. This safety feature slowly recharges the

battery until it is ready to accept the full charging

current. If the red and green lights continue to flash

after 20 minutes, replace the battery.

Unplug the charger from the 120V AC or 240V AC

outlet.

Removethe chargerunit from the tool case and plug

it into a 120V AC outlet. Set the charger base on a

stable surface. A green light will come on to indicate

the power is on and the charger circuit is ready.

PASLODE 240V 50HZ BATTERY CHARGING SYSTEM

AC-DC Adapter

Charger Base

DC Plug

Battery

Plug Receptacle

6ft. Cord

Battery

Charger

TECHNICAL DATA

Impulse Adapter (AC-DC)

Australia/New Zealand

Impulse Charger Base

Battery

7.4 VDC, 2150mAh, Lithium-ion

tupnI

240V, 50HZ

12VDC

Output Polarity

12VDC, 1.8A

PASLODE 120V 60HZ BATTERY CHARGING SYSTEM

Charger Input

Battery

7.4 VDC, 2150mAh, Lithium-ion

120V AC, 60HZ

Output Polarity

12VDC, 1.8A

1B.

Remove the wall transformer from the tool case and

plug into a 240V AC outlet. Set the charger base on a

stable surface and insert the wall transformer unitʼs plus

into the plug receptacle on the base of the charger (see

diagram). A green light indicates power is on and charg-

ing system is ready.

Australia/New ZealandNorth America

North America

Australia/New Zealand

Battery and Charging System

Inserting Battery

1. Load the battery, contacts first, into the Cordless

Framing Nailer.

2. Push battery fully forward into its locked position.

3. To remove battery, push down on locking tab and slide

battery out.

Battery Indicator Light

The illustration is a close-up of the side of the Paslode

Cordlessframerhandle.Onthesideofthehandleisasmall

plastic lens. This is the battery indicator light.

Whenyouinsertafully-chargedbatteryintothetool,youwill

seeablinkinggreenlight.Ifthelightblinksred,rechargethe

battery.

Battery

Indicator

Light

Battery Standby

The battery can be placed in the standby position if the

tool is not going to be used for a period of time.

To place the battery into the standby position, push down

on the locking tab and slide the battery back so that the

locking tab engages into the standby position in the handle.

NOTE:If battery is left in tool for an extended period of time

in the normal operating position, the battery will discharge

completely and will require recharging.

Locking Tab

Standby Position

Normal Operating Position

WARNING

EXPLOSION/FIRE

HAZARD

Read ALL safety instructions

before using

the fuel cell. Failure to fol-

low ALL instructions may

This may cause serious per-

sonal injuries or property

damage.

Keep the fuel cartridge

away from heat, sparks

and open flame. Do not

smoke when handling or

operating tool or fuel cart-

ridge.

Exposure to temperatures

above 120°F (49°C) may

the fuel cartridge to

burst, releasing

flammable

gas.

WARNING

Sunlight can raise the inside temperature of an

unventilated motor vehicle or storage container to

above 140°F (60°C).

Never puncture or attempt to open the fuel; it is

nonrefillable.

Never incinerate, reclaim or recycle the fuel.

Never smoke while installing or operating the fuel

cartridge or tool.

Never inhale the spray.

Keep out of the reach of children.

Store fuel cartridge(s) in well-ventilated areas only.

NOTE

Never attempt to refill the cartridge! Replace

with fresh fuel cartridge, and dispose of spent

cartridge properly.

Do not attempt to remove or reuse the fuel cart-

ridge cap.

2. Whenreplacingfuelcartridgealsocleanorreplace

air filter for optimum tool operation.

Fuel Cartridge

The fuel contains a small amount of oil to keep the tool

lubricated during use. It is not necessary to oil the tool

duringnormaloperation.Whencleaningthetool,useonly

Paslode Cordless tool oil. Using oils not formulated for the

Paslode Cordless Tool, may cause loss of power and may

damage the internal parts of the tool's motor.

NOTE: Altitude Restriction

Paslode Cordless tools are powered by an

internal

combustion engine and are effected by altitude. The

tool may lose power or not cycle consistantly at

elevationsof6000feetorgreater. For optimum perform-

ance use at 6000 feet or less.

DANGER

2. Do not attempt to install the fuel cartridge cap on

other fuel cells. This may result in damage to the

tool and injury to the user and by standers!

Quicklode™ Fuel Cartridge

There is a second container inside the fuel cartridge. This

inner container holds the fuel. The space between the

inner container and the outer cylinder is filled with a gas,

called the propellant, which is under pressure.

To eject the fuel, propellant pressure squeezes the inner

fuel container much as you squeeze a tube of toothpaste.

This squeezing action ensures that all the fuel is used,

and that the Cordless Nailer can operate in any position.

However, over time the propellant pressure diminishes

until it is no longer able to squeeze the inner fuel

container. This is why a nailer using a fuel cartridge

beyond the “Best Use Before” date may not work consis-

tently or at all.

If you expose the empty or expired fuel cartridge to

extreme temperatures, the propellant gas will expand and

could cause the container to burst, releasing flammable

gases.

cause

or handling

result in

explosion or fire.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Paslode Nagelpistole Handbücher

Paslode

Paslode FNS1850 Bedienungsanleitung

Paslode

Paslode IM360CI Bedienungsanleitung

Paslode

Paslode PS225C Bedienungsanleitung

Paslode

Paslode PF350-S Bedienungsanleitung

Paslode

Paslode 900600 Bedienungsanleitung

Paslode

Paslode PF 90 S Bedienungsanleitung

Paslode

Paslode CF325Li Bedienungsanleitung

Paslode

Paslode T250S-F16 Bedienungsanleitung

Paslode

Paslode IM200F 18 Bedienungsanleitung

Paslode

Paslode T250S-F16P Bedienungsanleitung

Paslode

Paslode Impulse IM90CI Bedienungsanleitung

Paslode

Paslode TrimMaster IM250A-Li Bedienungsanleitung

Paslode

Paslode CORDLESS 16 GAUGE ANGLED FINISH NAILER Handbuch

Paslode

Paslode RINGfast A515 Bedienungsanleitung

Paslode

Paslode IM200 F18 Bedienungsanleitung

Paslode

Paslode PFS160 Bedienungsanleitung

Paslode

Paslode FN1835 Bedienungsanleitung

Paslode

Paslode FN1565A34 Bedienungsanleitung

Paslode

Paslode 2125-F18 Bedienungsanleitung

Paslode

Paslode IMPULSE IM90i Bedienungsanleitung

Paslode

Paslode IM350+ Lithium Bedienungsanleitung

Paslode

Paslode IM200F 18 Bedienungsanleitung

Paslode

Paslode T200-F18 Bedienungsanleitung

Paslode

Paslode IM250A-Li2 Handbuch

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung