Paslode COILMASTER IM50S Bedienungsanleitung

PASLODE IMPULSE

COILMASTER IM50S

MANUAL

ANZ Product Code B40001

1 IM50S COILMASTER MANUAL

TABLE OF CONTENTS

GENERAL SAFETY INSTRUCTIONS

TOOL SAFETY INSTRUCTIONS

BATTERY SAFETY & CHARGING

FUEL CELL SAFETY

TOOL OVERVIEW

FUEL CELL LOADING PROCEDURE

CORRECT TOOL OPERATING PROCEDURES

PREPARING AND USE OF TOOL

TROUBLESHOOTING

TOOL MAINTENANCE

TOOL SPECIFICATIONS

SCHEMATICS

ACCESSORIES

IM50S COILMASTER MANUAL 2

Congratulations on the purchase of your new Paslode Cordless IM50S CoilMaster Nailer.

GENERAL SAFETY INSTRUCTIONS

The Impulse system consists of: tool, fuel cell, battery,

charger and fasteners. In the interests of operator

and system safety, the tool, fasteners and the fuel

cells referred to in the Paslode documents, must be

considered as one single, complete safety system.

WARNINGS

DO NOT ATTEMPT TO OPERATE

THIS TOOL UNTIL YOU HAVE

READ AND UNDERSTAND ALL

SAFETY PRECAUTIONS AND

MANUAL INSTRUCTIONS.

The Paslode Impulse IM50S CoilMaster is

an internal combustion device. It produces

hot exhaust gases that may ignite

ﬂammable materials. This tool must not

be used in a combustible environment or

in the presence of combustible materials,

such as ﬂammable chemicals, adhesives,

gasoline, or solvents.

Failure to follow all safety precautions and

instructions may result in a permanent

loss of vision, serious personal or even

fatal injury, property damage and/or tool

damage.

Do not expose the tool to temperatures in

excess of 49°C (120°F). Fuel and/or the

battery may burst, releasing ﬂammable

gas.

This tool must be operated only in a well-

ventilated environment, because the tool

exhausts carbon monoxide similar to a

petrol/gasoline lawnmower. Exposure to

carbon monoxide may cause dizziness,

nausea, or unconsciousness.

ALWAYS keep the Impulse IM50S

CoilMaster fuel cell, battery and battery

charger out of the reach of children.

ALWAYS wear eye and ear safety

equipment (PPE) when working with

or in the vicinity of the Paslode Impulse

IM50S CoilMaster.

The Impulse IM50S CoilMaster should not

be used in the rain or where excessive

moisture is present.

MAINTENANCE

Restrict Field Maintenance to the following:

CHECKING THE ENERGY LEVEL OF THE BATTERY

RECHARGING THE BATTERY

CHECKING THE FUEL CELL

REPLACING THE FUEL

CLEANING/REPLACING THE AIR FILTER

CLEARING A JAM

CLEANING AND LUBRICATING THE TOOL

(SEE CLEANING MANUAL INSTRUCTIONS (PG 12)

CAUTION

Never attempt any maintenance of a

Paslode Impulse tool without ﬁrst

removing the fasteners, fuel cell and

battery. Maintenance should be started

only after the tool is inoperative.

Operators should be capable of conducting basic

maintenance on the tool. This will not affect your tool

warranty.

FUEL CELL CHECK

Check the fuel cell. First remove the fuel cell from the tool

and check the “Best Use Before” date stamped on the

bottom of the cell.

CLEARING A NAIL JAM SAFELY

1. Remove the battery, fuel and fasteners.

2. Push the latch opening the magazine.

3. Clear jam, and push driver blade back up to its

rest position at the top of the cylinder.

4. Close magazine. Check contact probe moves freely.

FUEL CELL DISPOSAL

Dispose of all empty fuel cells responsibly. Remember to

dispose of these fuel cells where they will not be crushed,

punctured, burned or found by children.

Refer to your local authority regulations.

3 IM50S COILMASTER MANUAL

TOOL SAFETY INSTRUCTIONS

SAFETY INSTRUCTION:

TOOL OPERATION

1. EYE AND EAR PROTECTION.

Eye protection must meet the requirements

of AS/NZS 1337:1992 and should have side

shields for increased protection.

2. NEVER ASSUME THE TOOL IS EMPTY.

Never point the tool at yourself or anyone else.

3. NEVER ENGAGE IN “HORSEPLAY” WITH THE

TOOL.

Careless and improper use may results in a serious

accident.

4. NEVER CARRY THE TOOL WITH YOUR FINGER

ON, OR DEPRESSING, THE TRIGGER.

This practice may result in an accidental discharge

or a fastener.

5. NEVER OPERATE A TOOL THAT IS

MALFUNCTIONING.

Repair or refer to a service agent.

6. DO NOT LOAD FASTENERS WITH

THE TRIGGER OR SAFETY YOKE DEPRESSED.

A fastener may be accidently discharged.

7. NEVER OPERATE THE TOOL WITH THE WORK

CONTACT ELEMENT REMOVED OR DISABLED.

Never operate the tool if the work contact element

is not working properly or sliding freely.

8. ALWAYS POINT THE TOOL AWAY FROM YOUR-

SELF AND OTHERS WHEN CLEARING A JAM OR

REMOVING FASTENERS. ALWAYS REMOVE THE

FUEL CELL AND BATTERY BEFORE CHECKING

THE TOOL.

9. NEVER OPERATE THE IMPULSE COILMASTER

IF PARTS ARE LOOSE, DAMAGED OR MISSING.

10. DO NOT DRIVE FASTENERS INTO KNOTS OR

ON TOP OF OTHER FASTENERS.

A fastener may ricochet and cause serious injury.

11. OPERATE THE TOOL ONLY ON THE WORKPIECE.

12. NEVER DRIVE FASTENERS INTO AREAS WITH

CONCEALED HAZARDS.

Always check the area behind the work surface for

electrical wiring, gas, pipes, water pipes, sewer drains

or other potential hazards.

13. ALWAYS MAINTAIN SECURE AND

UNOBSTRUCTED FOOTING WHEN ON LADDERS,

PLATFORMS OR OTHER HIGH LOCATIONS.

14. ALLOW ONLY QUALIFIED PERSONNEL TO

OPERATE THE IMPULSE COILMASTER.

15. PROPERLY STORE FUEL CELL.

Always store fuel cells where they will not be

exposed to an open ﬂame, sparks, in direct

sunlight or temperatures above 25°C.

16. ALWAYS STORE THE TOOL WITH THE FUEL CELL

AND BATTERY REMOVED.

Store the fuel cells in the case with the Impulse

CoilMaster.

17. KEEP THE TOOL CLEAN AND WELL MAINTAINED.

18. KEEP YOUR HANDS CLEAR OF THE WORK

AREA SURFACE.

A fastener may exit at an angle

unexpectedly and cause injury.

19. OBSERVE LOCAL BATTERY AND FUEL CELL

DISPOSAL REGULATIONS.

20. WHEN NOT IN USE, REMOVE THE BATTERY

AND FASTENERS AND RETURN THE TOOL

TO ITS CASE.

21. IT IS NOT PERMITTED TO MAKE ANY

MODIFICATION TO THE TOOL, FUEL CELL OR

BATTERY OTHER THAN THOSE SPECIFIED BY

THE MANUFACTURER.

22. ONLY USE PASLODE SPECIFIED CONSUMABLES,

BATTERIES AND FUEL CELLS.

23. IF THE TOOL MISFIRES, ALWAYS REMOVE THE

BATTERY PRIOR TO EXAMINATION OF THE TOOL.

If the problem persists contact your local centre or

the tool manufacturer. The tool should be regularly

inspected for defective parts, loose screws (especially

after cleaning), etc and any defects rectiﬁed before

use. Check prior to each operation that the safety

mechanism is functioning properly.

IM50S COILMASTER MANUAL 4

BATTERY SAFETY & CHARGING

BATTERY AND CHARGING INSTRUCTIONS

1. Plug power adapter into charger base.

2. Connect to 240v AC outlet, a green light

indicates power is on.

3. Install battery, red light indicates battery is charging.

NOTE: If battery is completely discharged, the red

light and the green light may alternate back and

forth for up to 20 minutes. This safety feature slowly

recharges the battery until it is ready to accept the

full charging current. If the red and green lights

continue to alternate after 20 minutes, the battery

may be damaged.

4. After charging is complete, the green light will come on.

CHARGING TIMES

First charge (new battery) - 1 hour

Discharged Battery - 5 minutes to 1 hour

DO NOT:

Charge battery outdoors, in exposed wet

conditions, or in temperatures below 5°C

(40°F).

Allow metal objects to come in contact with

battery terminals.

Puncture or attempt to open battery case

or cells.

Store battery where it will be subjected to

temperatures above 49°C (120°F).

Incinerate battery.

Use a defective battery charger, one that

over-heats and/or smokes when plugged in.

Immerse the battery in water.

Do not short-circuit a battery.

Do not use a battery charger which heats

up excessively or gives off fumes when

connected - disconnect the charger

immediately.

The power adapter, charger base and battery are

designed to operate together as one system. Only use the

‘Paslode Impulse’ charger for ‘Paslode Impulse’ batteries.

The charging system is designed for use in covered areas.

Do not expose it to rain or to excessive humidity.

Arrange the charger lead appropriately to avoid

unnecessary damage. Do not use the charger if the cable

or plug is damaged. Replace immediately.

To avoid electrocution, disconnect the power supply

adapter before cleaning the terminals and contacts.

Use a dry cloth.

BATTERY DISPOSAL

Batteries and charging systems must be recycled or

taken to a designated disposal areas. (Subject to local

regulations)

TRANSPORT - LI ION BATTERY

& FUEL CELLS

The contained lithium-ion batteries are subject to the

Dangerous Goods Legislation requirements (see UN3480

or UN3481). The user can transport the batteries by road

without further requirements.

When being transported by third parties (eg: air transport

or forwarding agency), special requirements on packaging

and labelling must be observed. For preparation of the

item being shipped, consult an expert for hazardous

material if required.

Dispatch batteries only when the housing is undamaged.

Tape or mask off open contacts and pack up the battery

in such a manner that it cannot move around in the

packaging. Please also observe possibly more detailed

national regulations.

For the transport of Paslode fuel cells use UN Code

UN3478.

Transport of small amounts (<30 Kg ) in a private vehicle

is permitted without a transport and safety sheet (Limited

quantity exemption for road transport). The regulations by

transport categories are:

• Road/rail: ADR- RID - UN code 3478 class 2 code 5F

• Sea: IMDG - UN code 3478 + emergency instructions

sheet F·D, S-U

• Air: IATA - UN code 3478 class 2.1

Goods must be accompanied by the written safety

instruction of the chapter 5·4·3 of the ADR. Transport

by post is not permitted.

5 IM50S COILMASTER MANUAL

FUEL CELL SAFETY

WARNING

EXPLOSION/FIRE HAZARD

Read all instructions before using

or handling the fuel cell.

Keep the fuel cell away from heat, sparks

and open ﬂame. Do not smoke when

handling or operating tool or fuel cell.

Exposure to temperatures above 49°C

(120°F) may cause the fuel cell to burst,

releasing ﬂammable gas.

Sunlight can raise the inside temperature

of an unventilated motor vehicle or storage

container to above 60°C (140°F).

Never puncture or attempt to open

the fuel cell; it is non-refillable. Never

incinerate, reclaim or recycle the fuel cell.

Dispose of used cell responsibly.

Never smoke while installing the fuel

cell or operating the tool.

Never inhale the spray.

Store fuel cell(s) in well-ventilated areas

only.

Keep out of the reach of children.

Liquid gas can cause injury in the event

of contact with the skin or eyes.

FUEL CELL CHECK

Paslode Impulse fuel cells are marked with

a “Best Use Before” date on the bottom of

the can. For maximum performance use

fuel before the “Best Use Before” date.

COLD WEATHER OPERATION

Fuel combustion can be adversely affected at extreme low

temperatures. Ensure that the tool battery and fuel cell are

above the minimum operating temperature of 7°C (20°F)

before use.

The fuel cell is an aerosol product corresponding to the

2008/47/EC regulations. It contains:

• Liqueﬁed hydrocarbon gases (butane, propane,

propylene).

• A lubricant to maximise the tool durability.

When the fuel is used there will always be some

propellant left inside the cartridge. The fuel cell is always

pressurized. Its contents are extremely flammable. The

fuel cell is not reusable.

FUEL CELL DISPOSAL

Dispose of all empty fuel cells responsibly. Remember to

dispose of these fuel cells where they will not be crushed,

punctured, burned or found by children.

STORAGE

Stores and showrooms must comply with building

regulations. All local instructions corresponding to ﬁre

regulations must be followed.

• Where possible, store fuel at a stable temperature in

the range 7°C to 25°C. Do not expose to temperatures

exceeding 49°C.

• Do not use tools that emit ﬂames, sparks or reach high

temperatures in the vicinity that fuel cells are stored.

• Do not store in designated thoroughfares, hallways or

stairwells.

• Store in a well-ventilated area.

• Fuel cells must not be displayed in shop windows.

• Storage with pyrotechnic products is not permitted.

FIRST AID

• Direct contact with liquid gas may cause burns or

frostbite.

• In case of inhalation remove the person to fresh air,

and encourage breathing. Should the casualty become

unconscious, or breathing does not quickly return to

normal, summon urgent medical assistance.

• If gas gets into the eyes they should be ﬂushed out with

copious amounts of water. Skin contamination should

be removed with soapy water.

If symptoms persist, seek medical assistance.

IM50S COILMASTER MANUAL 6

TOOL OVERVIEW

= 200 nails

2.3 - 2.87mm

L 32mm to 50mm

Smooth, Ring and Screw

Type of head: Flat, Dome

OFF

DEPTH OF DRIVE

ADJUSTMENT

ON BOARD SPARE

NO-MAR TIP

ADJUSTABLE BELT HOOK

SOFT RUBBER HAND-GRIP

FLASHING GREEN = CHARGED

FLASHING RED = NEEDS CHARGING

COLLATION TEAR OFF

SUPPORT POST

7 IM50S COILMASTER MANUAL

FUEL CELL LOADING PROCEDURE

800

shots

per

cell

Fuel cell

expiry

on base

of can

CORRECT FUEL CELL LOADING PROCEDURE

To open - Push forward,

lift then back

Open fuel door

Carefully align fuel adaptor

and cell stem

Fuel adaptor locks in up

position

Remove fuel cell carefully

Load fuel cell To close - Push forward

then down to lock fuel

door

Load

fuel

cell

65 7

1 2 3 4

ALWAYS REMOVE

BATTERY, FUEL CELL

AND FASTENERS

WHEN SERVICING

OR CLEARING A JAM.

ONLY USE PASLODE’S SPECIALLY FORMULATED FUEL, FAILURE TO DO SO MAY DAMAGE YOUR TOOL,

CAUSE MISFIRES AND VOID WARRANTY.

IM50S COILMASTER MANUAL 8

CORRECT TOOL OPERATING PROCEDURES

= 200 nails

2.3 - 2.87mm

L 32mm to 50mm

Head type: Flat and Dome

Coating: Zinc plate, galv, stainless steel

CORRECT NAIL LOADING PROCEDURE

Open nose gate

1. Close magazine cover

ﬁrst

2. Close nose gate and

latch

Open magazine cover Place coil into magazine Feed nails into nose

1 2 3 4

5 6

CORRECT REMOVAL OF EXCESS COLLATION TAPE

Fold tape at right angles

across front of tool nose.

Only then tear off collation.

Locking tab post support

collation

The tool has a locking tab which is designed to hold the

tape in place. Check locking tab is positioned correctly

in hole provided in collation tape. The correct use of

this locking tab ensures nails can not be dislodged from

collation strip during removal of excess tape.

WARNING: Do not pull collation tape straight out of

nose. This incorrect action will dislodge nails already fed

into firing chamber and may cause nail to jam.

MAGAZINE NAIL LENGTH TRAY

Adjustable nail length tray for short nail support Adjust nail length tray for long nail support

9 IM50S COILMASTER MANUAL

PREPARING AND USE OF TOOL

FOR FIXING METAL CONNECTING PLATES

Instructions: Use 32mm hardened ballistic (cone) tip

nails. For maximum performance use CoilMaster nails

(B40020). Do not over drive nail - the underside of the

nail head should rest against metal plate surface.

ADJUSTING THE DEPTH OF DRIVE - THUMB WHEEL ROTATION

Metal Plate Surface

+ +

Counter

Sunk Proud

INCREASE

DEPTH OF DRIVE

DECREASE

DEPTH OF DRIVE

ALWAYS WEAR

EYE AND HEARING

PROTECTION

TOOL FIRING SEQUENCE

1000/hour max fire rate / 2 nails/second / 7°C to 40°C

BANG!

BZZZZZ

1 2 3 4

Depress work contact

probe

Actuate trigger, tool ﬁres Allow recoil, work contact

is released

Trigger released

CORRECT BATTERY OPERATION

ON/OFF SWITCH. Battery has 2 secure lock positions:

engaged and disengaged

OFFON

Green indicates

charged battery

Red indicates battery

needs recharging

Inhaltsverzeichnis

Andere Paslode Nagelpistole Handbücher

Paslode

Paslode FN1835.1 Bedienungsanleitung

Paslode

Paslode IM250A Bedienungsanleitung

Paslode

Paslode DF90S Bedienungsanleitung

Paslode

Paslode IM250A Bedienungsanleitung

Paslode

Paslode T250-F16 Bedienungsanleitung

Paslode

Paslode Cordless Framing Nailer Bedienungsanleitung

Paslode

Paslode 902600 Bedienungsanleitung

Paslode

Paslode 3250-F16 Kurzanleitung

Paslode

Paslode FN1565A34 Bedienungsanleitung

Paslode

Paslode FN 1665 Bedienungsanleitung

Paslode

Paslode 575057 Bedienungsanleitung

Paslode

Paslode T250-F16 Bedienungsanleitung

Paslode

Paslode PF 90 S Bedienungsanleitung

Paslode

Paslode 360Xi Bedienungsanleitung

Paslode

Paslode 16 Handbuch

Paslode

Paslode 901000 Bedienungsanleitung

Paslode

Paslode FN2265 Bedienungsanleitung

Paslode

Paslode FN1835 Bedienungsanleitung

Paslode

Paslode CF325Li Bedienungsanleitung

Paslode

Paslode PSN50NP Bedienungsanleitung

Paslode

Paslode F150S-PP Bedienungsanleitung

Paslode

Paslode F325R Bedienungsanleitung

Paslode

Paslode T250S-F16P Bedienungsanleitung

Paslode

Paslode 900600 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung