Patton electronics 1000R Bedienungsanleitung

MODEL 1000R and

1000RS

Async. Short Range

Modem for Modular

EIA/TIA-561 Systems

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part #07M1000R-B

Doc. #082011UB

Revised 04/28/98

USER

MANUAL

An ISO-9001

Certified Company

1.0 WARRANTY INFORMATION

Patton Electronicswarrants all Model 1000R components to be

free from defects, and will—at our option—repair or replace the product

should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials, and

does not cover customer damage, abuse or unauthorized modification.

If this product fails or does not perform as warranted, your sole

recourse shall be repair or replacement as described above. Under no

condition shallPatton Electronicsbe liable for any damages incurred

by the use of this product. These damages include, but are not limited

to, the following: lost profits, lost savings and incidental or

consequential damages arising from the use of or inability to use this

product. Patton Electronicsspecifically disclaims all other warranties,

expressed or implied, and the installation or use of this product shall be

deemed an acceptance of these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Model 1000R generates and uses radio frequency energy, and

if not installed and used properly—that is, in strict accordance with the

manufacturer's instructions—may cause interference to radio and

television reception. The Model 1000R has been tested and found to

comply with the limits for a Class A computing device in accordance

with the specifications in Subpart J of Part 15 of FCC rules, which are

designed to provide reasonable protection from such interference in a

commercial installation. However, there is no guarantee that

interference will not occur in a particular installation. If the Model

1000R does cause interference to radio or television reception, which

can be determined by disconnecting the modem, the user is

encouraged to try to correct the interference by one or more of the

following measures: moving the computing equipment away from the

receiver, re-orienting the receiving antenna and/or plugging the

receiving equipment into a different AC outlet (such that the computing

equipment and receiver are on different branches).

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates

that it is in compliance with the Electromagnetic Compatibility (EMC)

directive and the Low Voltage Directive (LVD) of the Union European

(EU). A Certificate of Compliance is available by contacting Patton

Technical Support.

1.3 SERVICE

All warranty and nonwarranty repairs must be returned freight

prepaid and insured to Patton Electronics. All returns must have a

Return Materials Authorization number on the outside of the shipping

container. This number may be obtained from Patton Electronics

Technical Service at

telephone: (301) 975-1007,

web address: http://www.patton.com;

email: [email protected].

NOTE:Packages received without an RMA number will not be

accepted.

Patton Electronics’ technical staff is also available to answer any

questions that might arise concerning the installation or use of your

Model 1000R. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

3.0 INSTALLATION

The Model 1000R is easy to install. This section tells you how to

properly connect the Model 1000R to the twisted pair and EIA/TIA-561

interfaces, and how to operate the Model 1000R.

3.1 CONNECTION TO THE TWISTED PAIR INTERFACE

The Model 1000R supports data-only communication between an

EIA/TIA-561 device and another serial device. There are two

requirements for installation:

1. These units work in pairs. Therefore, you must have one Model

1000R or compatible modem at each end of a two twisted pair

cable.

2. To function properly, the Model 1000R needs two twisted pairs of

metallic wire. The pairs must be unconditioned, dry metallic wire,

between 19 and 26 AWG (the higher number gauges may limit

distance). Standard dial-up telephone circuits or leased circuits

that run through signal equalization equipment are not acceptable.

For your convenience, the Model 1000R is available with two

different twisted pair interfaces: an RJ-11 jack or an RJ-45 jack.

3.1.1 TWISTED PAIR CONNECTION USING RJ-11 OR RJ-45

The RJ-11 and RJ-45 connectors on the Model 1000R's twisted

pair interface are pre-wired for a standard TELCO wiring environment

(see Figure 1). The table on the following page shows the signal/pin

relationships.

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.

This product has been thoroughly inspected and tested and is

warranted for One Year parts and labor. If any questions or problems

arise during installation or use of this product, please do not hesitate to

contact Patton Electronics Technical Support at (301) 975-1007.

2.1 FEATURES

• Connects directly to the EIA/TIA-561 device

• Range to 17 miles (27.2 km)

• Data rates to 19,200 bps

• No AC power or batteries required

• Miniature size fits in tight locations

• RJ-11 and RJ-45 twisted pair connection

• Silicon Avalanche Diode surge protection (1000RS only)

• Compatible withPatton Models 1000, 1009 and 1015

• Made in USA

2.2 DESCRIPTION

The Patton Model 1000RLow-Cost Short Range Modem allows

an EIA/TIA-561 device to communicate with RS-232 devices at

distances up to 17 (27.2 km) miles over two unconditioned twisted pair.

Supporting asynchronous data rates to 19.2 Kbps, the Model 1000R

requires no AC power or batteries.

Measuring only 2.0” x 1.7” x .8” (5.1 x 4.3 x 2.0 cm), the Model

1000R is housed in an ABS plastic case. Connection to the EIA/TIA-

561 serial port is achieved using a modular RJ-45 jack. Connection to

the twisted pair interface is made through either an RJ-11 jack or an RJ-

45 jack. The serial device at the other end of the twisted pair cable can

be connected to the Model 1000R using a Patton Model 1000 (DB-25),

1009 (DB-9), 1015 (DB-15) or another Model 1000R.

The Model 1000S is a surge protected version of the Model 1002

that uses the latest in bi-directional, clamping, transient suppressors to

protect itself and connected equipment against harmful transient

discharges. For surge handling capability, the Model 1000S is

compliant with IEC 801.5 level 2, 1kV.

1 - Blue

2 - Orange

3 - Black

4 - Red

5 - Green

6 - Yellow

7 - Brown

8 - Slate

1 - Blue

2 - Yellow

3 - Green

4 - Red

5 - Black

6 - White

Figure 1. AT&T standard modular color codes

Model 1000R EIA/TIA-561 8 Position Interface:

Pin No. Function

1--------------------------------DSR

2--------------------------------DCD

3--------------------------------DTR

4--------------------------------SG

5--------------------------------RD

6--------------------------------TD

7--------------------------------CTS

8--------------------------------RTS

3.3 OPERATING THE MODEL 1000R

Once the Model 1000R is properly installed, it should operate

transparently—as if it were a standard cable connection. Operating

power is derived from the EIA/TIA-561 data and control signals; there is

no “ON/OFF” switch.

RJ-11SIGNAL RJ-45 SIGNAL

1----------------GND†1----------------N/C

2----------------RCV-2----------------GND†

3----------------XMT+ 3----------------RCV-

4----------------XMT-4----------------XMT+

5----------------RCV+ 5----------------XMT-

6----------------GND†6----------------RCV+

7----------------GND†

8----------------N/C

When connecting two Model 1000Rs, it is necessary to use a

“crossover” cable. The diagram below shows how a crossover cable

should be constructed for an environment where both Model 1000Rs

use a 4-wire RJ-11 connector. Similar logic should be followed when

using an RJ-45 connector or a combination of the two.

SIGNAL PIN# COLOR‡COLOR PIN#SIGNAL

GND†1Blue---------------------White 6GND†

RCV-2Yellow------------------Red 4XMT-

XMT+ 3Green------------------Black 5RCV+

XMT-4Red---------------------Yellow 2RCV-

RCV+ 5Black-------------------Green 3XMT+

GND†6White-------------------Blue 1GND†

†Connection to ground is optional

‡Standard color codes—yours may be different

3.2 CONNECTION TO THE EIA/TIA-561 SERIAL PORT

Every serial device connected to the Model 1000R must have a

special interface cable that conforms to the EIA/TIA-561 standard. On

one end, this cable must have a male RJ-45 plug, on the other end, it

must have a connector that fits into your serial device. The diagram on

the following page shows the pin connections for the Model 1000R.

Connect each pin to the appropriate connection on your serial device.

APPENDIX B

PATTON MODEL 1000R CABLE RECOMMENDATIONS

The Patton Model 1000R operates at frequencies of 20kHz or less

and has been performance tested by Patton technicians using twisted-

pair cable with the following characteristics:

Wire Gauge Capacitance Resistance

19 AWG/.9mm 83nf/mi or 15.72 pf/ft. .0163 Ohms/ft.

22 AWG/.6mm 83nf/mi or 15.72 pf/ft. .0326 Ohms/ft.

24 AWG/.5mm 83nf/mi or 15.72 pf/ft. .05165 Ohms/ft.

To gain optimum performance from the Model 1002, please keep

the following guidelines in mind:

• Alwaysuse twisted pairwire—this is not an option.

• Use twisted pair wire with a capacitance of 20pf/ft or less.

• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid higher

AWGnumbers than 26)

• Use of twisted pair with a resistance greater than the above

specifications may cause a reduction in maximum distance

obtainable. Functionality should not be affected.

• Environmental factors too numerous to mention can affect the

maximum distances obtainable at a particular site. Use “maximum

distance” figures as a general guideline only.

APPENDIX A

PATTON MODEL 1000R SPECIFICATIONS

Transmission Format:Asynchronous

Data Rate: 0 to 19,200 bps

Distance: See table below

Surge Protection: Compliant with IEC 801.5 level 2, 1kV

(Model 1000RS only)

Control Signal: DCD (pin 2) and DSR (pin 1) turn on when

modem is powered up (connected); CTS

(pin 7) turns on immediately after the

terminal raises RTS (pin 8)

Transmit Line: 4-wire, unconditioned line

Transmit Mode: Full duplex, 4-wire

Transmit Level: 0 dBm

Line Connection: RJ-11, RJ-45

Power Supply: No external power required, uses ultra low

power from data and control signals

Temperature: 32° to 140°F

Humidity: 95% non-condensing

Size:2.0” x 1.7” x 0.8” (5.1 x 4.3 x 2.0 cm)

24 AWG

(0.5 mm) 26 AWG

(0.4 mm)

19 AWG

( 0.9 mm)

19,200 6.2(9.9) 3.7(5.9) 1.2(1.9)

9,600 7.5(12.0) 4.9(7.8) 2.5(4.0)

4,800 8.7(13.9) 5.6(9.0) 3.7(5.9)

2,400 11.8(18.9) 8.0(12.8)4.9(7.8)

1,200 17.0(27.2)11.8(18.9)8.0(12.8)

Data Rate

(bps)

Model 1000 Distance Table in Miles (km)

Wire Gauge

APPENDIX B

PATTON MODEL 1000R BLOCK DIAGRAM

Patton Electronics Company

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Patton electronics Modem Handbücher

Patton electronics

Patton electronics 1194 Bedienungsanleitung

Patton electronics

Patton electronics 12168 Bedienungsanleitung

Patton electronics

Patton electronics 2703 Bedienungsanleitung

Patton electronics

Patton electronics 1008 Bedienungsanleitung

Patton electronics

Patton electronics Kilolight 1184 Bedienungsanleitung

Patton electronics

Patton electronics RocketLink 3202 Bedienungsanleitung

Patton electronics

Patton electronics 1082/F Bedienungsanleitung

Patton electronics

Patton electronics 1058DVs Bedienungsanleitung

Patton electronics

Patton electronics 1193 Bedienungsanleitung

Patton electronics

Patton electronics 1020 Bedienungsanleitung

Patton electronics

Patton electronics 1202 Bedienungsanleitung

Patton electronics

Patton electronics 1090 Bedienungsanleitung

Patton electronics

Patton electronics 1068 Bedienungsanleitung

Patton electronics

Patton electronics 1170M SERIES Bedienungsanleitung

Patton electronics

Patton electronics 1070RC Bedienungsanleitung

Patton electronics

Patton electronics 1140 Bedienungsanleitung

Patton electronics

Patton electronics 1000 Bedienungsanleitung

Patton electronics

Patton electronics 1092A Bedienungsanleitung

Patton electronics

Patton electronics 1010B Bedienungsanleitung

Patton electronics

Patton electronics DIAMONDLINK 3201 Bedienungsanleitung

Patton electronics

Patton electronics Model 1065 Bedienungsanleitung

Patton electronics

Patton electronics 1140A Bedienungsanleitung

Patton electronics

Patton electronics 1006 Bedienungsanleitung

Patton electronics

Patton electronics 1000 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung