Patton electronics 470 Series Bedienungsanleitung

USER

MANUAL

MODEL 470 Series

ATM Coax to Twisted Pair

Adapters (Baluns)

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part #07M470-A

Doc. #019091UA

Revised 9/11/98

PATTON MODEL 470 SERIES SPECIFICATIONS

Tranmission Medium:155.52 Mbps ATM over Twisted Pair

75 Ohm Connection:Dual BNC Coax Connectors (female, 75

Ohm)

Power SupplyNone Required

Dimensions:

Model 470:100 Ohm CAT-5 single 8-pin RJ-45 Jack,

Shielded

Model 471:120 Ohm CAT-5 Single 8-pin RJ-45 Jack,

Shielded

Model 472:150 Ohm IBM Data Connector, 2 Twisted

Pair, Shielded

An ISO-9001

Certified Company

WARRANTY

Patton Electronicswarrants all Model 470 Series components to

be free from defects, and will—at our option—repair or replace the

product should it fail within one year from the first date of shipment. This

warranty is limited to defects in workmanship or materials, and does not

cover customer damage, abuse or unauthorized modification. If this

product fails or does not perform as warranted, your sole recourse shall

be repair or replacement as described above. Under no condition shall

Patton Electronicsbe liable for any damages incurred by the use of this

product. These damages include, but are not limited to, the following:

lost profits, lost savings and incidental or consequential damages arising

from the use of or inability to use this product. Patton Electronics

specifically disclaims all other warranties, expressed or implied, and the

installation or use of this product shall be deemed an acceptance of

these terms by the user.

SERVICE AND SUPPORT

All warranty and non-warranty repairs must be returned freight

prepaid and insured to Patton Electronics. All returns must have a

Return Materials Authorization number on the outside of the shipping

container. This number may be obtained from Patton Electronics

Technical Service at (301) 975-1007; http://www.patton.com: or,

[email protected]. NOTE:Packages received without an RMA

number will not be accepted. Patton Electronics' technical staff is also

available to answer any questions that might arise concerning the

installation or use of your Model 470 Series. Technical Service hours:

8AM to 5PM EST, Monday through Friday.

CE NOTICE

The CE symbol on your Patton Electronics equipment indicates that

it is in compliance with the Electromagnetic Compatibility (EMC)

directive and the Low Voltage Directive (LVD) of the Union European

(EU). A Certificate of Compliance is available by contacting Patton

Technical Support.PRODUCT DESCRIPTION

The Patton Model 470 Series ATM balunsallow 75 ohm coax

hardware to communicate with 100 Ohm, 120 Ohm, or 150 Ohm twisted

pair equipment. The Model 470 Series presents a ready solution to this

termination mismatch. Supporting ATM data rates to 155.52 Mbps, the

Model 471/471/472 convert 75 Ohm signals and vice versa to 100, 120,

and 150 Ohm twisted pair, respectively.

Model 470: 75 Ohm to 100 Ohm CAT-5 Single 8-Pin RJ-45 Jack,

Model 471: 75 Ohm to 120 OhmCAT-5 single 8-Pin RJ45 Jack,

Model 472: 75 Ohm to 150 Ohm IBM Data Connector (2 Twisted Pair)

CONFIGURATIONCONFIGURATION

The Model 470 Series are pre-set to work in most applications

without additional configuration. The only parameter that is user-

configurable is shield connection between the 75 Ohm coax and twisted

pair interfaces. The diagram below shows how the shield is connected

between the modular jack and dual BNCs. Removing the jumper

breaks the connection.

Coax BNC (75 Ohm JumperRJ-45 (100/120)

or IDC (150 Ohm)

TX ShieldJP1RJ-45 Shield, IBM IDC Shield

TX ShieldJP2RJ-45 Shield, IBM IDC Shield

The factory setting leaves both jumpers JP1 and JP2 in place, thus

passing both shield connections through. To break one or both of the

shield connections, follow these instructions:

1)Insert a small flat blade screwdriver into the slot on the side of

the Model 470 Series case and twist. The case will pop open,

exposing the PC board.

2)Holding the PC board with the modular jack facing left,

located jumper JP1 toward the top of the board and JP2

toward the bottom of the board. Remove the desired

jumper(s) from the two pins on the right (for JP1) and from the

2 pins on the left (for JP2) to break one or both shield

connections. NOTE:do not lose the jumper(s).

3)Re-align the case halves and end inserts and snap the case

halves back together.

INSTALLATION

The Model 470 Series is easy to install and requires no AC power

or batteries for operation. After making any necessary configuration

changes (see above), simple plug in the modular and coax cables as

indicated on the case. The pin/contact configuration of the 100/120

Ohm RJ-45 and 150 Ohm IDC modular connectors is shown below:

RJ-45 Pin(s)IDC ContactFunction

1 BTransmit +

2OTransmit -

7RReceive +

8GReceive -

Dieses Handbuch passt für folgende Modelle

Andere Patton electronics Netzwerkkarte Handbücher

Patton electronics

Patton electronics 1180RC Bedienungsanleitung

Patton electronics

Patton electronics 1092RC Bedienungsanleitung

Patton electronics

Patton electronics 1092ARC Bedienungsanleitung

Patton electronics

Patton electronics NetLink 1095RC Bedienungsanleitung

Patton electronics

Patton electronics 2500RC Bedienungsanleitung

Patton electronics

Patton electronics 1018RC Bedienungsanleitung

Patton electronics

Patton electronics 1110RC Bedienungsanleitung

Patton electronics

Patton electronics 1193RC Bedienungsanleitung

Patton electronics

Patton electronics 1000RC Bedienungsanleitung

Patton electronics

Patton electronics 2703RC-A Bedienungsanleitung

Patton electronics

Patton electronics 1004ARC Bedienungsanleitung

Patton electronics

Patton electronics 1045RC Bedienungsanleitung

Patton electronics

Patton electronics 1012ARC Bedienungsanleitung

Patton electronics

Patton electronics 1080ARC Bedienungsanleitung

Patton electronics

Patton electronics 6103 Bedienungsanleitung

Patton electronics

Patton electronics 1065RC Bedienungsanleitung

Patton electronics

Patton electronics IM2RC/F Bedienungsanleitung

Patton electronics

Patton electronics 2703RC Bedienungsanleitung

Patton electronics

Patton electronics 1206RC Bedienungsanleitung

Patton electronics

Patton electronics 2701RC Bedienungsanleitung

Patton electronics

Patton electronics G.SHDSL NTU Bedienungsanleitung

Patton electronics

Patton electronics NetLink 1001MC Bedienungsanleitung

Patton electronics

Patton electronics 1205RC Bedienungsanleitung

Patton electronics

Patton electronics 1060RC Bedienungsanleitung

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Cisco

Cisco MC16E Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITXR Bedienungsanleitung

Gigafast

Gigafast EE101-AEX Bedienungsanleitung