Patton electronics SmartNode 4830 Series Bedienungsanleitung

SmartNode 4830 Series

Analog VoIP Integrated Access

Device

Quick Start Guide

Sales Ofﬁce:

+1 (301) 975-1000

Technical Support:

+1 (301) 975-1007

E-mail:

[email protected]

WWW:

www.patton.com

Document Number:

13219U7-001 Rev. C

Part Number:

07MSN4830-QS

Revised:

May 16, 2007

Approval

Models that are equipped with telecom interfaces have been approved for connection to the public telecommunication network as listed

under PSTN regulatory compliance.

Important

This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial

or residential environment.

Start Installation

For Quick

Start Installation

For Quick

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

Patton Electronics Company, Inc.

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

Tel: +1 (301) 975-1000

Fax: +1 (301) 869-9293

Support: +1 (301) 975-1007

Web: www.patton.com

E-mail: [email protected]

Trademark Statement

Patton,

the Patton logo, and

SmartNode

are registered trademarks of Patton Electronics

Company. The terms

SmartWare

and

SmartView Management Center

are trademarks of

Patton Electronics Company. All other trademarks presented in this document are the

property of their respective owners.

The information in this document is subject to change without notice. Patton Elec-

tronics assumes no liability for errors that may appear in this document.

In no event shall Patton Electronics or its employees and associated companies be lia-

ble for any incidental, special, indirect or consequential damages whatsoever, including

but not limited to lost proﬁts, arising out of or related to this manual or the informa-

tion contained within it, even if Patton Electronics has been advised of, known, or

should have known, the possibility of such damages.

Important Information

To use virtual private network (VPN) and/or AES/DES/3DES encryption capabilities

with the SmartNode 4830, you may need to purchase additional licenses, hardware,

software, network connection, and/or service. Contact

[email protected]

+1 (301) 975-1000

for assistance.

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

Introduction

SmartNode 4830 Quick Start Guide

Introduction

This Quick Start Guide leads you through the basic steps to set up a new SmartNode (see ﬁgure 1) and to

download a conﬁguration. Please note that this guide does not replace the detailed Software Conﬁguration

Guide and the Getting Started Guide on the CD-ROM and available online at

www.patton.com/voip

Figure 1. SmartNode product (SmartNode 4838 shown)

SmartNodes can be used for a wide variety of IP and voice over IP applications. To support and ease the conﬁg-

uration of the SmartNodes conﬁguration templates for the most important applications are available online at

http://www.patton.com/voip/appnotes.shtml

Setting up a new SmartNode consists of the following steps:

Connect a PC to the SmartNode, log in and conﬁgure your LAN IP address (see page 4 for details)

Connect the SmartNode to the LAN (see page 6)

Download a conﬁguration example, adapt it to your network, and load it onto the SmartNode (see page 6)

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

Connecting a PC, logging in, and configuring the LAN IP address

SmartNode 4830 Quick Start Guide

Connecting a PC, logging in, and conﬁguring the LAN IP address

Connecting power and conﬁguring the default IP address

Connect the SmartNode to the mains power supply using the included power supply and cable. When the

RUN

LED stops blinking and remains lit, the SmartNode is ready.

The factory default IP settings are listed in table 1. If these addresses do not work with your network they must

be changed. Contact your network administrator if you are not sure which IP address to use in

your installation.

Note

The DHCP server is running on the ETH 0/1 of the SN4830 Series

models. All Ethernet ports are pre-conﬁgured and active.

Connecting to a PC and logging in

To access the SmartNode conﬁguration, connect a PC equipped with an RS-232 console port to the

Con-

sole

port on the front of the SmartNode. Use the included black Ethernet cable and RJ45 to DB-9 adapter

for this purpose (Model 16F-561).

Figure 2. Connecting to the PC

Open a Terminal connection to the SmartNode. Use the Terminal program included with most PC operat-

ing systems (e.g. Hyper Terminal on Windows). The CD-ROM also includes some recommended termi-

nal programs.

Table 1. Factory default IP address and network mask conﬁguration

Item IP Addresss(es) Network Mask

WAN interface Ethernet 0 (ETH 0/0) DHCP DHCP

LAN interface Ethernet 1 (ETH 0/1) 192.168.1.1 255.255.255.0

DHCP server address range 192.168.1.10-192.168.1.19 255.255.255.0

Serial Terminal

Note A Patton Model 16F-561 RJ45 to DB-9 adapter is included with

each SmartNode 4000 Series device

Console

VoIP Gateway Router

ToIP Integrated Access Device

SmartNode 4524

Link

100M

Activity

0/00/10/20/3

Enet 0 Voice Ports

Power

Run

VoIP Link

Link

100M

Activity

Enet 1

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

Connecting a PC, logging in, and configuring the LAN IP address

SmartNode 4830 Quick Start Guide

Type

administrator

as the login prompt and press the

Enter

key after the password prompt (do not type

anything for the password). A prompt will appear consisting of the IP address and

character.

administrator

password:

172.16.40.1>

Following log in, the SmartNode is in operator execution mode (indicated by

character in the command

line prompt). With the commands

enable

and

conﬁgure

, you enter the conﬁguration mode.

172.16.40.1>

enable

172.16.40.1#

configure

172.16.40.1(cfg)#

Changing the IP address

Select the context IP mode to conﬁgure an IP interface.

172.16.40.1(cfg)#

context ip router

172.16.40.1(ctx-ip)[router]#

Set the IP address and network mask for the each IP interface (

eth0

, for example).

Note

For the examples in this guide, a private network (

172.16.1

) IP

address is used.

172.16.40.1(ctx-ip)[router]#

interface eth0

172.16.40.1(if-ip)[eth0]#

ipaddress 172.16.1.10 255.255.255.0

2002-10-29T00:09:40 : LOGINFO : Link down on interface eth0.

2002-10-29T00:09:40 : LOGINFO : Link up on interface eth0.

172.16.1.10(if-ip)[eth0]#

Make this modiﬁed conﬁguration your new start-up conﬁguration. On the next start-up the system will

initialize itself using the modiﬁed conﬁguration.

172.16.1.10 (if-ip)[eth0]#

copy running-config startup-config

172.16.1.10 (if-ip)[eth0]#

Go to section “Connecting the SmartNode to the LAN” on page 6 to connect the SmartNode to

your network.

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

Connecting the SmartNode to the LAN

SmartNode 4830 Quick Start Guide

Connecting the SmartNode to the LAN

The 4830 Ethernet ports are auto MDX, therefore a straight-through wired cable can be used for host and

switch connections (see ﬁgure 3).

Figure 3. Connecting the SmartNode to the network

You can check the connection with the ping command to another host on the local LAN.

172.16.1.99(if-ip)[eth0]#ping <IP Address of the host>

Respectively from the host:

ping 172.16.1.99

Note

To ping outside your local LAN, you will need to conﬁgure the

default gateway.

You may now start to conﬁgure the SmartNode from scratch using the CLI commands, but we recommend

that you start your conﬁguration from a template. See “Downloading a conﬁguration example, adapting it to

your network, and loading it onto the SmartNode” on page 6 for further details.

For a detailed description of the CLI refer to the

SmartWare Software Conﬁguration Guide

(SCG) available on

the CD-ROM and online at:

www.patton.com/voip

Downloading a conﬁguration example, adapting it to your network,

and loading it onto the SmartNode

Patton provides a collection of conﬁguration templates on the CD-ROM that came with the SmartNode

device—and also on the support page at

www.patton.com/voip/appnotes.shtml

—one of which may be simi-

lar enough to your application that you can use it to speed up conﬁguring the SmartNode. Simply download

the conﬁguration note that matches your application to your PC. Adapt the conﬁguration as described in the

conﬁguration note to your network (remember to modify the IP address) and copy the modiﬁed conﬁguration

to a TFTP server. The SmartNode can now load its conﬁguration from this server.

Note

Patton regularly adds new conﬁguration templates to the collection at

www.patton.com/voip/appnotes.shtml,

so if you do not see your applica-

tion on the CD-ROM, it may have been added to the website.

Network

interface ETH 0

Cross-over cable

SmartNode

Host

Network

interface ETH 0

Straight-through

wired cable SmartNode

Host

Hub

Straight-through

wired cable

Console

VoIPGateway Router

ToIPIntegrated Access Device

SmartNode 4524

Link

100M

Activity

0/00/10/20/3

Enet 0 VoicePorts

Power

Run

VoIPLink

Link

100M

Activity

Enet 1

Console

VoIPGateway Router

ToIPIntegrated Access Device

SmartNode 4524

Link

100M

Activity

0/00/10/20/3

Enet 0 VoicePorts

Power

Run

VoIPLink

Link

100M

Activity

Enet 1

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

Additional information

SmartNode 4830 Quick Start Guide

Note

If your application is unique and not covered by any of Patton’s conﬁgura-

tion templates, you can manually conﬁgure the SmartNode instead of load-

ing a conﬁguration ﬁle template. In that case, refer to the

SmartNode Series

SmartWare Software Conﬁguration Guide

for information on conﬁguring the

SmartNode device.

In this example we assume the TFTP server on the host with the IP address 172.16.1.11 and the conﬁguration

named

SN.cfg in the root directory of the TFTP server.

172.16.1.99(if-ip)[eth0]#copy tftp://172.16.1.11/SN.cfg startup-config

Download...100%

172.16.1.99(if-ip)[eth0]#

After the SmartNode has been rebooted the new startup conﬁguration will be activated.

172.16.1.99(if-ip)[eth0]#reload

Running configuration has been changed.

Do you want to copy the 'running-config' to the 'startup-config'?

Press 'yes' to store, 'no' to drop changes : no

Press 'yes' to restart, 'no' to cancel : yes

The system is going down

Additional information

For detailed information about conﬁguring and operating guidance, set up procedures, and troubleshooting,

refer to the SmartNode Series SmartWare Software Conﬁguration Guide and the SmartNode Getting Started Guide

on the enclosed Patton VoIP CD-ROM or at http://www.patton.com/voip/. On the CD-ROM you will also

ﬁnd numerous freeware and shareware tools, including TFTP servers, Telnet clients, etc..

When you issue the reload command, the SmartNode will ask

if you want to copy the running conﬁguration to the startup con-

ﬁguration. Since you just downloaded a conﬁguration ﬁle to the

startup conﬁguration you must answer this question with

Otherwise, the downloaded conﬁguration will be overwritten

and lost!

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

Compliance 8

SmartNode 4830 Quick Start Guide

Compliance

EMC compliance:

•FCC Part 15, Class A

•EN55022, Class A

•EN55024

Safety compliance:

•UL60950-1/CSA C22.2 No. 60950-1

•IEC 60950-1

•EN60950-1

PSTN regulatory compliance:

•FCC Part 68

•CS-03

•TBR 21

•TBR 12 & 13 (E1)

•AS/ACIF S016:2001 (E1)

•AS/ACIF S043:2005 (DSL Models)

Radio and TV Interference (FCC Part 15)

The SmartNode product generates and uses radio frequency energy, and if not installed and used properly-that

is, in strict accordance with the manufacturer’s instructions-may cause interference to radio and television

reception. The SmartNode product have been tested and found to comply with the limits for a Class A com-

puting device in accordance with speciﬁcations in Subpart B of Part 15 of FCC rules, which are designed to

provide reasonable protection from such interference in a commercial installation. However, there is no guar-

antee that interference will not occur in a particular installation. If the SmartNode product does cause interfer-

ence to radio or television reception, which can be determined by disconnecting the unit, the user is

encouraged to try to correct the interference by one or more of the following measures: moving the computing

equipment away from the receiver, re-orienting the receiving antenna and/or plugging the receiving equipment

into a different AC outlet (such that the computing equipment and receiver are on different branches).

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

FCC Part 68 (ACTA) Statement (FXO ports) 9

SmartNode 4830 Quick Start Guide

FCC Part 68 (ACTA) Statement (FXO ports)

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom

side of this equipment is a label that contains—among other information—a product identiﬁer in the format

US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with

the applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance

that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone

company will notify the customer as soon as possible. Also, you will be advised of your right to ﬁle a complaint

with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could

affect the operation of the equipment. If this happens the telephone company will provide advance notice in

order for you to make necessary modiﬁcations to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company.

If the equipment is causing harm to the telephone network, the telephone company may request that you dis-

connect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public

service commission or corporation commission for information.

Industry Canada Notice (FXO ports)

This equipment meets the applicable Industry Canada Terminal Equipment Technical Speciﬁcations. This is

conﬁrmed by the registration number. The abbreviation, IC, before the registration number signiﬁes that regis-

tration was performed based on a Declaration of Conformity indicating that Industry Canada technical speci-

ﬁcations were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protec-

tive, operational and safety requirements. The Department does not guarantee the equipment will operate to

the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be con-

Disconnect all power before servicing.

The SmartNode product contains no user serviceable parts.

The mains outlet that is utilized to power the equipment must be

within 1 foot (3 meters) of the device and shall be easily accessi-

ble.

CAUTION

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

CE Notice 10

SmartNode 4830 Quick Start Guide

nected to the facilities of the local telecommunications company. The equipment must also be installed using

an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line

individual service may be extended by means of a certiﬁed connector assembly (telephone extension cord). The

customer should be aware that compliance with the above condition may not prevent degradation of service in

some situations. Repairs to some certiﬁed equipment should be made by an authorized maintenance facility

designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment mal-

functions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the ground connections of the power utility, telephone lines

and internal metallic water pipe system, are connected together. This protection may be particularly important

in rural areas.

CE Notice

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the

laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual rec-

ognition of their conformity.

The safety advice in the documentation accompanying this product shall be obeyed. the conformity to the

above directive is indicated by the CE sign on the device.

EC Declaration of Conformity

(see section “EG-Konformitätserklärung” for German version)

Product Description: SmartNode 4830

The products described above in the form as delivered are in conformity with the provisions of the following

European Directive:

R&TTE Directive 1999/5/EC

Guidelines of the European Parliament and the Committee for the Harmonisation of the Legal Regula-

tions of the Member States concerning radio equipment and telecommunications terminal equipment and

the mutual recognition of their conformity.

The signed Declaration of Conformity can be downloaded from www.patton.com/certiﬁcations/

Approval

Models that are equipped with FXO ports have been approved for connection to the public telecommunica-

tion network.

EG-Konformitätserklärung

(see section “EMC compliance:” for English version)

Produktbezeichnung: SmartNode 4830

Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften

folgender Richtlinie überein:

The safety advices in the documentation accompanying the products shall be obeyed. The

conformity to the above directive is indicated by the CE sign on the device.

VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

Andere Handbücher für SmartNode 4830 Series

Inhaltsverzeichnis

Andere Patton electronics Netzwerk-Router Handbücher

Patton electronics

Patton electronics OnSite 2884 Bedienungsanleitung

Patton electronics

Patton electronics PASSERELLES ROUTEURS VOIP 455X Konfigurationshandbuch

Patton electronics

Patton electronics SmartNode 4520 Series Bedienungsanleitung

Patton electronics

Patton electronics 2112 Bedienungsanleitung

Patton electronics

Patton electronics ONSITE 2603 Bedienungsanleitung

Patton electronics

Patton electronics 3210 Bedienungsanleitung

Patton electronics

Patton electronics SL4020 Bedienungsanleitung

Patton electronics

Patton electronics SL4020 Bedienungsanleitung

Patton electronics

Patton electronics 3087 Bedienungsanleitung

Patton electronics

Patton electronics 3060/V24 Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4634 Series Bedienungsanleitung

Patton electronics

Patton electronics SmartLink 4020 Series Bedienungsanleitung

Patton electronics

Patton electronics 2121 Bedienungsanleitung

Patton electronics

Patton electronics IM1/I4 Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4950 Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4900 Bedienungsanleitung

Patton electronics

Patton electronics 4900 Series Bedienungsanleitung

Patton electronics

Patton electronics OnSite 2800 Series Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4552 Bedienungsanleitung

Patton electronics

Patton electronics DIAMONDLINK 3201 Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4110 Series Bedienungsanleitung

Patton electronics

Patton electronics 4520 Bedienungsanleitung

Patton electronics

Patton electronics 4110 Series Bedienungsanleitung

Patton electronics

Patton electronics Patton IPLink 2635 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise