Patton electronics ENVIRONET EHA3201 Bedienungsanleitung

Model EHA3201

EnviroNET

G.SHDSL Router

Quick Start Guide

Important

—This is a Class A device and is intended for use in a light industrial environment. It is not

intended nor approved for use in an industrial or residential environment.

Part Number: 07MEHA3201-QS, Rev. C

Revised: February 16, 2012

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

2EHA3201 Quick Start Guide

• Do not open the device when the power cord is connected. For sys-

tems without a power switch and without an external power

adapter, line voltages are present within the device when the power

cord is connected.

• For devices with an external power adapter, the power adapter shall

be a listed Limited Power Source The mains outlet that is utilized to

power the device shall be within 10 feet (3 meters) of the device,

shall be easily accessible, and protected by a circuit breaker in compli-

ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets all

applicable standards for the country in which it is to be installed.

• For AC powered devices which have 3 conductor power plugs (L1, L2

& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet

(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are

rated for proper voltage, current, anticipated temperature, flammabil-

ity, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous voltages

present regardless of whether the device is powered ON or OFF.

PSTN relates to interfaces such as telephone lines, FXS, FXO, DSL,

xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazardous net-

work voltages” and to avoid electric shock use caution when working

near these ports. When disconnecting cables for these ports, detach

the far end connection first.

• Do not work on the device or connect or disconnect cables during peri-

ods of lightning activity.

When the EHA3201 is mounted, it shall be secured in such a

way as to withstand a vertical shear force of 90N or 20lbs.

In accordance with the requirements of council directive 2002/96/EC on

Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-

of-life you separate this product from other waste and scrap and deliver

to the WEEE collection system in your country for recycling.

WARNING

EHA3201 Quick Start Guide 3

1.0 Installing the EHA3201

To install the EHA3201, follow these steps:

1. Make a ground connection for the unit (refer to section 1.1, “Grounding the EHA3201” on page 4).

2. Connect the line interface between the units (refer to section 1.2, “Connecting the Twisted-Pair Line Inter-

face” on page 4)

Note See

figure 1

for the EHA3201 unit’s bottom panel arrangements.

3. Connect the Ethernet interface (refer to section 1.3, “Connecting the 10/100Base-T Ethernet Interface”

on page 4).

4. Connect the power plug (refer to section 1.4, “Connecting Power” on page 5).

Figure 1.

EHA3201 Bottom Panel

Electrostatic Discharge (ESD) can damage equipment and impair electrical

circuitry. It occurs when electronic printed circuit cards are improperly

handled and can result in complete or intermittent failures. Do the follow-

ing to prevent ESD:

• Always follow ESD prevention procedures when removing and replac-

ing cards.

• Wear an ESD-preventive wrist strap, ensuring that it makes good

skin contact. Connect the clip to an unpainted surface of the chassis

frame to safely channel unwanted ESD voltages to ground.

• To properly guard against ESD damage and shocks, the wrist strap

and cord must operate effectively. If no wrist strap is available,

ground yourself by touching the metal part of the chassis.

WARNING

EnviroNET

EHA3201

Ethernet

port

Line twisted-pair

RJ-45 interface

EnviroNET

POWERDATA

LINE

Power

Groundin

Stud

4EHA3201 Quick Start Guide

1.1 Grounding the EHA3201

Before installing the EnviroNET G.SHDSL Router, it is important to establish a good grounding connection first.

1. Assemble a ground wire using #10 AWG wire with green-and-yellow-colored insulation and two ring ter-

minals. Make the wire long enough to reach one of the following earth ground sources:

•

The building ground rod (generally located at the site’s main service entrance)

•

A sprinkler system pipe

•

A cold-water pipe

•

Building structural steel

2. Install the grounding wire between the grounding stud (see Figure 1 on page 3) and the grounding

source.

1.2 Connecting the Twisted-Pair Line Interface

To function properly, the G.SHDSL Router must be connected using twisted-pair, unconditioned, dry, metal wire,

between 19 (0.9mm) and 26 AWG (0.4mm). Leased circuits that run through signal equalization equipment are

not acceptable.

The G.SHDSL Router is equipped with an RJ-45 interface jack (Line), which is a two-wire interface. Observe the

signal/pin relationships on the G.SHDSL Router’s Line interface jack. The signal/pin relationship is shown in

figure 2.

Figure 2. EnviroNET G.SHDSL Router (RJ-45) twisted pair line interface.

1.3 Connecting the 10/100Base-T Ethernet Interface

The G.SHDSL Router has an unshielded RJ-45 auto-MDIX10/100Base-T interface. This port is designed to con-

nect directly to a 10/100Base-T network. figure 3 shows the signal/pin relationships on this interface. You may

connect this port to a hub or PC using a straight through or crossover cable that is up to 328 ft long.

1 (no connection)

2 (no connection)

3 (no connection)

4 (2-Wire RING)

5 (2-Wire TIP)

6 (no connection)

7 (no connection)

8 (no connection)

EHA3201 Quick Start Guide 5

Figure 3. EnviroNET G.SHDSL Router 10/100Base-T RJ-45 Connector Pinout

1.4 Connecting Power

The EHA3201 is an internally powered unit. The power connection is made via the 3-pin power connector on the

bottom panel of the EnviroNET G.SHDSL Router. A mating connector is provided to create the mating cable (see

figure 4). No configuration is necessary for the power supply.

Figure 4. Connecting the power cable

The EnviroNET G.SHDSL Router does not have a power switch, so it powers up as soon as it is plugged in.

There are no user-serviceable parts in the EnviroNET G.SHDSL

Router. Fuse replacement should only be performed by qualified

service personnel. Contact Patton Electronics Technical support at

(301) 975-1007 for more information.

1 TX+ (data output from the G.SHDSL router)

2 TX- (data output from the G.SHDSL router)

3 RX+ (data input to the G.SHDSL router)

4 (no connection)

5 (no connection)

6 RX- (data input to the G.SHDSL router)

7 (no connection)

8 (no connection)

EHA3201/R/

LNNL

L = +24

N = Ground

L = Line

N = Neutral

E = Earth

WARNING

6EHA3201 Quick Start Guide

Note It does not matter whether the positive (+) or negative (-) side of the DC power supply is grounded.

However, the polarity on the power source must be matched up properly to the EHA3201 power input

(i.e. negative power source terminal to negative power input; positive power source terminal to positive

power input).

2.0 Configuring the EHA3201

The EnviroNET G.SHDSL Router comes pre-configured to communicate with other devices on the network. To

futher configure the EHA3201, you may log into the web management system.

2.1 Connect to a PC

1. Connect the EHA3201’s Data port to your PC (see figure 5).

2. The PC used for configuring the EHA3201 should be set for DHCP client.

3. Connect the EHA3201 to a power source to turn on the unit.

4. The EHA3201 Data port uses the DHCP client to automatically assign an IP address and netmask. The

EHA3201 will send the IP address to the PC.

5. Enter the EHA3201’s IP address in the address bar of the web browser.

6. Log in and perform any desired configuration changes through the EHA3201’s web browser interface.

Figure 5. Connecting the EHA3201 to the local IP network

For information on changing the IP address, refer to Chapter 3 “Quick Start Installation” in the Model 3201 &

3241 User Manual.

Connect to

Ethernet port

(

DATA

)

Ethernet port

EnviroNET

POWERDATA

LINE

EHA3201 Quick Start Guide 7

2.2 Configuring applications

The EHA3201 is typically used in a bridged or routed application. For instruction on how to configure the

EHA3201 for an application, refer to the Model 3201 & 3241 User Manual.

Bridged Applications

•

For a bridged application connecting standalone units back-to-back, see pages 29-32 in the Model 3201 &

3241 User Manual.

•

For a bridged application connecting the CPE to a DSLAM, see pages 38-46 in the Model 3201 & 3241 User

Manual.

Routed Applications

•

For a routed application connecting standalone units back-to-back, see pages 32-38 in the Model 3201 &

3241 User Manual.

•

For a routed application connecting the CPE to a DSLAM, see pages 46-77 in the Model 3201 & 3241 User

Manual.

3.0 Additional Information

For detailed information about configuring and operating guidance, set up procedures, and troubleshooting,

refer to the DiamondLink 3201 & 3241 User Manual available online at www.patton.com/manuals/

3201.pdf.

A.0 Customer and Technical Support

Toll-Free VoIP support: call sip:[email protected]om with a VoIP SIP phone

Online support: www.patton.com

E-mail support: s[email protected]—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)

8EHA3201 Quick Start Guide

B.0 EHA Case Specifications

B.1 Power Requirements

•

UAC: 110, 220VAC, 2.25W

B.2 Temperature Range

•

-40–185°F (-40–85°C)

B.3 Humidity

•

Up to 90% non-condensing.

B.4 Dimensions

•

8”H x 9.25”W x 3.25”D

B.5 Weight

•

6.4lb (2.9kg)

Note For Model 3201 unit specifications, refer to the

Model 3201 & 3241 User Manual

available online

www.patton.com/manuals.

EHA3201 Quick Start Guide 9

C.0 Compliance Information

C.1 Compliance

EMC:

•

FCC Part 15, Class A

•

EN55022, Class A

•

EN55024

Safety:

•

UL 60950-1/CSA C22.2 N0. 60950-1

•

IEC/EN60950-1

•

AS/NZS 60950-1

PSTN Regulatory:

•

FCC Part 68

•

CS-03

•

AS/ACIF S043:2003

C.2 FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of

this equipment is a label that contains—among other information—a product identifier in the format US:

AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with the

applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that

temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone com-

pany will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with

the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could

affect the operation of the equipment. If this happens the telephone company will provide advance notice in

order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If

the equipment is causing harm to the telephone network, the telephone company may request that you discon-

nect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser-

vice commission or corporation commission for information.

10 EHA3201 Quick Start Guide

3.3 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con-

firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra-

tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications

were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,

operational and safety requirements. The Department does not guarantee the equipment will operate to the

user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed using an acceptable

method of connection. In some cases, the company’s inside wiring associated with a single line individual service

may be extended by means of a certified connector assembly (telephone extension cord). The customer should

be aware that compliance with the above condition may not prevent degradation of service in some situations.

Repairs to some certified equipment should be made by an authorized maintenance facility designated by the

supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for

their own protection that the ground connections of the power utility, telephone lines and internal metallic water

pipe system, are connected together. This protection may be particularly important in rural areas.

C.4 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in

strict accordance with the manufacturer's instructions—may cause interference to radio and television recep-

tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accor-

dance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable

protection from such interference in a commercial installation. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception,

which can be determined by disconnecting the cables, try to correct the interference by one or more of the fol-

lowing measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna,

and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and

receiver are on different branches).

Inhaltsverzeichnis

Andere Patton electronics Netzwerk-Router Handbücher

Patton electronics

Patton electronics OnSite 2884 Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 5400 Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4830 Series Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4520 Series Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4830 Series Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4110 Series Bedienungsanleitung

Patton electronics

Patton electronics IPLink 2802 Bedienungsanleitung

Patton electronics

Patton electronics SMART NODE 4950-NCE Bedienungsanleitung

Patton electronics

Patton electronics 4020 Series Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4552 Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4552 Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4960 Series Bedienungsanleitung

Patton electronics

Patton electronics 4630 Series Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4960 Series Bedienungsanleitung

Patton electronics

Patton electronics Patton IPLink 2603 Bedienungsanleitung

Patton electronics

Patton electronics IM 1/I Bedienungsanleitung

Patton electronics

Patton electronics IM2RC/I-100B Bedienungsanleitung

Patton electronics

Patton electronics ONSITE 2603 Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4630 Series Bedienungsanleitung

Patton electronics

Patton electronics IPLink 2823 Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4552 Bedienungsanleitung

Patton electronics

Patton electronics 3060/V24 Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4110 Series Bedienungsanleitung

Patton electronics

Patton electronics OnSite 1052 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise