Patton OnSite 2701A/I Bedienungsanleitung

OnSite™ Model 2701A/I

E1/T1 Ethernet Bridge (NTU)

Quick Start Guide

Important—This is a Class A device and is intended for use in a light

industrial environment. It is not intended nor approved for use in

an industrial or residential environment.

Part Number: 07MOS2701AI-QS, Rev. A

Revised: February 13, 2017

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

Web: www.patton.com

2OnSite 2701A/I Quick Start Guide

1.0 Introduction

Your OnSite device comes with one of the following power supply options:

•External AC adapter with included power cord

•Internal AC power supply

•Internal DC power supply—no power accessories are included

• The device contains no user serviceable parts. The

equipment shall be returned to Patton Electronics for

repairs, or repaired by qualified service personnel.

• Mains Voltage: Do not open the case the when the

power cord is attached. Line voltages are present

within the power supply when the power cords are

connected. The mains outlet that is utilized to power

the device shall be within 10 feet (3 meters) of the

device, shall be easily accessible, and protected by a

circuit breaker.

• For AC powered units, ensure that the power cable

used meets all applicable standards for the country

in which it is to be installed, and that it is connected

to a wall outlet which has earth ground.

• For units with an external power adapter, the adapter

shall be a listed Limited Power Source.

• Hazardous network voltages are present in WAN

ports regardless of whether power to the unit is ON

or OFF. To avoid electric shock, use caution when

near WAN ports. When detaching the cables, detach

the end away from the device first.

• Do not work on the system or connect or disconnect

cables during periods of lightning activity.

• The interconnecting cables shall be acceptable for

external use and shall be rated for the proper applica-

tion with respect to voltage, current, anticipated tem-

perature, flammability, and mechanical serviceability.

Use only a 12V certified Limited Power Source external

power adapter marked LPS.

WARNING

CAUTION

OnSite 2701A/I Quick Start Guide 3

1.1 Models with external AC adaptor

1. Connect female plug of the AC power cord to the AC adapter provided.

2. Connect the barrel-type connector of the AC adapter to the barrel-type Power jack

on the OnSite device.

3. Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC).

1.2 Models with internal AC power supply

1. Insert the female end of the AC power cord into the internal power supply connec-

tor.

2. Connect the male end of the power cord into an AC power outlet (100–240 VAC).

1.3 Models with internal DC power supply

1. Strip insulation 1/4-inch from the electrical wires that will connect the DC power

source to the OnSite device.

2. Connect the positive (+) terminal from the power source to the positive (+) termi-

nal on the OnSite device.

3. Connect the ground terminal from the power source to the ground terminal (E) on

the OnSite device.

4. Connect the negative (-) terminal from the power source with to the negative (-)

terminal on the OnSite device.

Figure 1. Connecting the DC power supply

Note “+”, “E”, and “-” may be unlabeled.

1.4 Power-up indication

The Power LED blinks as the OnSite device is powering up. When the Power LED stops

blinking and remains lit, the device is ready for you to configure.

2.0 Configure the IP address

The OnSite device is shipped with a factory-configured IP address assigned to the

Ethernet LAN port (green outline). The address is 192.168.200.10/24. In most cases,

+E-

4OnSite 2701A/I Quick Start Guide

you must change the address to be on the same subnet as your PC, as described in the

procedures below. If you are not sure which IP address to use for your installation,

contact your network administrator.

2.1 Connecting a PC and logging in

1. Using the included combination RS232/Ethernet cable and DB9-RJ45 adapter,

connect a PC’s serial port to the OnSite device’s Console port (see figure 2).

Figure 2. Connecting OnSite device to the PC’s serial port

2. Start a HyperTerminal session on the PC using the settings: 9600 bps, 8 data bits,

1 stop bit, no parity, no flow control

3. Log in to the OnSite device using the factory-default login and password:

Password: superuser

Note A power supply can be installed on the remote unit even if the unit is

receiving power across the line.

2.2 Modifying the IP address

1. Display current IP interface settings for the OnSite device’s Ethernet LAN port.

→ip list interfaces <enter>

IP Interfaces:

ID | Name | IP Address | DHCP | Transport

---|------|----------------|----------|--------------

1 | ip1 | 192.168.200.10 | disabled | <eth1>

----------------------------------------------------

2. Modify the IP address for the LAN port according to your network requirements.

→ip set interface ip1 ipaddress 10.10.10.5 255.255.255.0

Link

Frame

Link

100M

WANEthernet

Power

Console

Connect to Console port

Serial port

PC with

terminal emulator

OnSite™NTU

E1/T1 to Ethernet

OnSite 2701A/I Quick Start Guide 5

Note The above IP address (10.10.10.5/24) is only an example. You must

choose an IP address on the same subnet as your PC.

3. Verify the new address is correct and save it in system boot memory.

→ip list interfaces <enter>

→system config save <enter>

→

Now you can connect the OnSite device to your local IP network and complete the

remaining configuration from your PC using a standard web browser.

3.0 Connect to the local IP network

1. Connect the OnSite device’s (green) Ethernet port to the same Ethernet segment as

your PC (see figure 3).

2. Press the MDI-X switch until the Ethernet Link LED turns on.

Figure 3. Connecting the OnSite device to the local IP network

You can check the network connection with the ping command. For example, you

would ping 10.10.10.5 from your PC.

4.0 Log onto the web management interface

You will now access the web management Graphical User Interface (GUI) to configure

the OnSite device using a standard web browser (such as Microsoft Edge or Google

Chrome web browser).

1. At your PC, open a web browser and enter the IP address you assigned to the

OnSite device’s Ethernet LAN port in step 2 of section 2.2 “Modifying the IP

address” on page 4.

2. Log in to the web management home page using the username superuser and the

password superuser.

Crossover

10/100

EthernetWAN

Power

MDI-X

RXTX

Connect to

Ethernet port

MDI-X switch

6OnSite 2701A/I Quick Start Guide

Figure 4. OnSite device’s web management home page

3. Now you can use the OnSite device’s web management pages to complete your

configuration (see section 3. “Plug one end of the cable into the receive socket

(labeled RX) on the OnSite device. Plug the other end of the cable into the

transmit port of the E1 device.” on page 7).

5.0 Connect the WAN port

The OnSite device comes with a T1/E1 WAN interface (presented on a single RJ-48C

connector with selectable line impedances of 100-ohms for T1 and 120-ohms for E1

lines). The OnSite device also comes with dual BNC connectors for alternate connection

to unbalanced 75-ohm E1 lines.

To connect the WAN port on an OnSite device, or if you plan to use the RJ-48C port on

an OnSite device, refer to section “Connecting to the RJ-48C WAN port”. Otherwise,

refer to section “Connecting to the unbalanced 75-ohm TX and RX WAN ports” to

install cables onto the BNC connectors on the OnSite device.

5.1 Connecting to the RJ-48C WAN port

1. Obtain a twisted-pair cable with an RJ-48C plug connector at each end.

2. Plug one end of the cable into the RJ-48C socket (labeled WAN) on the OnSite

device.

3. Plug the other end of the cable into the T1/E1 device.

5.2 Connecting to the unbalanced 75-ohm TX and RX WAN ports

1. Obtain a coaxial cable with a BNC connector at each end.

OnSite 2701A/I Quick Start Guide 7

2. Plug one end of the cable into the transmit socket (labeled TX) on the OnSite

device. Plug the other end of the cable into the receive port of the E1 device.

3. Plug one end of the cable into the receive socket (labeled RX) on the OnSite device.

Plug the other end of the cable into the transmit port of the E1 device.

6.0 Complete the installation

To finish configuring your OnSite device, and for detailed information about installing,

configuring, operating, and troubleshooting, refer to the OnSite Model 2701A/I E1/T1

Ethernet Bridge (NTU) User Manual available online at www.patton.com/manuals/.

7.0 Customer and Technical Support

Toll-Free VoIP support: call sip:support@patton.com with a VoIP SIP phone

Online support: www.patton.com

E-mail support: support@patton.com—answered within 1 business day

Telephone support:

A.0 Compliance Information

A.1 Compliance

EMC:

•FCC Part 15, Class A

•EN55022, Class A

•EN55024

Safety:

•UL60950-1/CSA C22.2 No. 60950-1

•IEC/EN 60950-1

•AS/NZS 60950-1

Standard USA +1 (301) 975-1007 Monday–

Friday

8:00 am–5:00 pm

EST (1300–2200 UTC/GMT)

Alternate Switzerland +41 (0)31-985-2555 Monday–

Friday

8:00 am–5:00 pm

CET (0900–1800 UTC/GMT)

8OnSite 2701A/I Quick Start Guide

PSTN Regulatory:

•These devices are not intended for connection to the PSTN.

A.2 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and

used properly—that is, in strict accordance with the manufacturer's instructions—may

cause interference to radio and television reception. This equipment has been tested

and found to comply with the limits for a Class A computing device in accordance with

the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide

reasonable protection from such interference in a commercial installation. However,

there is no guarantee that interference will not occur in a particular installation. If the

equipment causes interference to radio or television reception, which can be detemined

by disconnecting the cables, try to correct the interference by one or more of the fol-

lowing measures: moving the computing equipment away from the receiver, re-orient-

ing the receiving antenna, and/or plugging the receiving equipment into a different AC

outlet (such that the computing equipment and receiver are on different branches).

A.3 CE Declaration of Conformity

Product Description: OnSite 2701A/I

We certify that the apparatus described above conforms to the requirements of Council

Directive 2004/108/EC on the approximation of the laws of the member states relating

to electromagnetic compatibility; and Council Directive 2006/95/EC on the approxima-

tion of the laws of the member states relating to electrical equipment designed for use

within certain voltage limits.

The safety advice in the documentation accompanying this product shall be obeyed.

The conformity to the above directive is indicated by the CE sign on the device.

The signed Declaration of Conformity can be downloaded from www.patton.com/certi-

fications/.

A.4 Authorized European Representative

D R M Green

European Compliance Services Limited

Avalon House, Marcham Road

Abingdon,

Oxon, OX14 1UD, UK

The safety notices in the documentation accompanying the

products shall be obeyed. The conformity to the above direc-

tive is indicated by the CE sign on the device.

OnSite 2701A/I Quick Start Guide 9

The information in this document is subject to change without notice. Patton Electron-

ics assumes no liability for errors that may appear in this document.

Trademarks statement

The term OnSite is a trademark of Patton Electronics Company. All other trademarks

presented in this document are the property of their respective owners.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the OnSite Model 2701A/

I E1/T1 Ethernet Bridge (NTU) User Guide available online at www.patton.com/manu-

als.

In accordance with the requirements of council directive

2002/96/EC on Waste of Electrical and Electronic Equip-

ment (WEEE), ensure that at end-of-life you separate this

product from other waste and scrap and deliver to the

WEEE collection system in your country for recycling.

10 OnSite 2701A/I Quick Start Guide

NOTES

____________________________________________________________________

Andere Handbücher für OnSite 2701A/I

Inhaltsverzeichnis

Andere Patton Netzwerk-Router Handbücher

Patton

Patton SmartNode 5570 Bedienungsanleitung

Patton

Patton ForeFront 6500 Bedienungsanleitung

Patton

Patton SmartNode 5200 Bedienungsanleitung

Patton

Patton SmartNode 4634 Series Bedienungsanleitung

Patton

Patton OnSite 3300 Bedienungsanleitung

Patton

Patton SmartNode 5200 Bedienungsanleitung

Patton

Patton SmartNode 5300 Bedienungsanleitung

Patton

Patton SmartLink 4020 Bedienungsanleitung

Patton

Patton SmartNode 4900 Bedienungsanleitung

Patton

Patton OnSite 3210 Series Bedienungsanleitung

Patton

Patton OnSite 2603 Bedienungsanleitung

Patton

Patton ipRocketLink 3101 Series Bedienungsanleitung

Patton

Patton OnSite 2603 Bedienungsanleitung

Patton

Patton BODi rS BD007 Series Bedienungsanleitung

Patton

Patton 2805 Bedienungsanleitung

Patton

Patton IPLINK 2800 series Bedienungsanleitung

Patton

Patton OnSite OS3300 Bedienungsanleitung

Patton

Patton ForeFront 6400 Bedienungsanleitung

Patton

Patton SmartNode 5400 Series Bedienungsanleitung

Patton

Patton OnSite 2701A/I Bedienungsanleitung

Patton

Patton SmartNode 4660 Series Bedienungsanleitung

Patton

Patton SN5300/4B/EUI Bedienungsanleitung

Patton

Patton SL4020 Bedienungsanleitung

Patton

Patton DiamondLink 3201 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung