Patton OnSite 3300 Bedienungsanleitung

OnSite™ Model 3300

EFM Router

Quick Start Guide

Important—This is a Class A device and is not intended nor approved for use in an industrial

or residential environment.

Part Number:

07MOS3300-QS

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: suppor[email protected]

WWW: www.patton.com

2OnSite 3300 Quick Start Guide

•Do not open the device when the power cord is connected. For systems

without a power switch and without an external power adapter, line

voltages are present within the device when the power cord is con-

nected.

•For devices with an external power adapter, the power adapter shall be

a listed Limited Power Source. The mains outlet that is utilized to power

the device shall be within 10 feet (3 meters) of the device, shall be eas-

ily accessible, and protected by a circuit breaker in compliance with local

regulatory requirements.

•For AC powered devices, ensure that the power cable used meets all

applicable standards for the country in which it is to be installed.

•For AC powered devices which have 3 conductor power plugs (L1, L2 &

GND or Hot, Neutral & Safety/Protective Ground), the wall outlet (or

socket) must have an earth ground.

•For DC powered devices, ensure that the interconnecting cables are

rated for proper voltage, current, anticipated temperature, flammability,

and mechanical serviceability.

•WAN, LAN & PSTN ports (connections) may have hazardous voltages

present regardless of whether the device is powered ON or OFF. PSTN

relates to interfaces such as telephone lines, FXS, FXO, DSL, xDSL, T1,

E1, ISDN, Voice, etc. These are known as ?hazardous network volt-

ages? and to avoid electric shock use caution when working near these

ports. When disconnecting cables for these ports, detach the far end

connection first.

•Do not work on the device or connect or disconnect cables during periods

of lightning activity.

This device contains no user serviceable parts. This device can only be

repaired by qualified service personnel.

This device is NOT intended nor approved for connection to the PSTN. It is

intended only for connection to customer premise equipment.

WARNING

OnSite 3300 Quick Start Guide 3

1.0 Hardware Installation

1.1 Contents of Package

•OS3300 EFM Router

•External power supply for OnSite Model 3300

•Ethernet cable with RJ45 plugs on each end (included)

1.2 What you will need

•Default unit IP address: 192.168.200.10

•Default username: admin

•Default password: (no password)

•PC Computer

1.3 Identify the connector and attach the cables

All connectors are on the rear panel of the OS3300 Router.

Figure 1. All connectors are on the rear panel of the OS3300 EFM Router

Connect the DSL Interface

To function properly, the OS3300 must be connected using a twisted-pair, unconditioned, dry, metal wire,

between 19 (0.9mm) and 26 AWG (0.4mm). Leased circuits that run through signal equalization equipment are

not acceptable.

The EFM Router is equipped with a RJ-45 interface jack (DSL), which conforms to the T568B standard. Any stan-

dard Category 5e cable can be used to directly connect two routers. Depending on the router model, it will have

a two-wire, four-wire or eight-wire interface. Observe the signal/pin relationship on the OS3300’s DSL interface

jack for each pair in Figure 2. Figure 4 shows the proper way to wire a cable with a RJ-45 jack on one end and

four RJ-11jacks on the other.

4OnSite 3300 Quick Start Guide

Figure 2. OS3300 (RJ-45) twisted pair DSL interface

Figure 3. OnSite Pinout for two devices

Figure 4. RJ-45 to RJ-11 cable

OnSite 3300 Quick Start Guide 5

2.0 Connecting Interfaces

2.1 Connecting Console Interface

Install the supplied RJ-45-to-RJ-45 cable with the DB9-RJ45 adapter between the OS3300 RS-232 port and an

open serial port on your computer. If you need to assemble your own cable, refer to the pinout diagram in

figure 5.

Figure 5. DB-9-to-RJ-45 cable diagram

2.2 Connect the Ethernet Interface

The EFM Router has four unshielded RJ-45 auto-MDIX10/100Base-T interfaces. These are designed to connect

directly to a 10/100Base-TX network. Figure 6 shows the signal/pin relationships on this interface. You may

connect this port to a hub or PC using a straight through or crossover cable that is up to 328 ft long.

2.3 Connect the PoE Interface (optional)

The RJ-45 port is an Auto-MDIX 10/100Base-T interface. This port is designed to connect directly to a 10/

100Base-T network. Figure 6 shows the signal/pin relationships on this interface. You may connect this port to

any Ethernet enabled device using a straight-through or crossover cable that is up to 328 ft long. PoE enabled

devices such as IP cameras, Voice over IP (VoIP) phones and wireless access points may draw the PoE. The router

injects power on the data pair pins 1/2 (PoE+) and 3/6 (PoE-) of the connector labeled “Eth 3.” The power injec-

tion conforms to the 802.3af specification, and will deliver the 55 volts with a maximum of 13 watts. A 12 volt 3

amp external power supply is required for PoE.

Figure 6. OS330010/100Base-T RJ-45 Connector Pinout

6 DSR

1 CD

4 DTR

5 SG

2 RD (driven by access server)

3 TD (received by access server)

8 CTS (driven by access server)

7 RTS (received by access server)

Wired together

(No other electrical

connection)

RJ-45 Jack Signal NameDB-9

1 TX+ (data output, PoE+)

2 TX- (data output, PoE-)

3 RX+ (data input, PoE+)

4 (no connection)

5 (no connection)

6 RX- (data input, PoE-)

7 (no connection)

8 (no connection)

6OnSite 3300 Quick Start Guide

Note PoE referenced in Figure 6 applies to Ethernet 0/3 only.

2.4 Connect the Power Source

The EFM Router does not have a power switch; it powers on once the device is plugged in.

The power connection is made via the barrel jack on the rear panel of the OS3300. No configuration is necessary

for the power supply.

2.5 Router/Bridge Status LEDs

The LEDs indicate the status of power, the WAN (OnSite) PoE, and Ethernet connections.

Note When powered down, the LED indicators are clear; when powered on, the LED indicators are yellow.

Figure 7. OS3300 front panel

Table 1. OS3300 front panel LEDs

LED Name LED Function Description

Power ON Indicates power is applied.

ROFF

WAN is configured as CO.

WAN is configured as CPE.

OnSite Pair

(one LED for each port [1

on OS3301, 2 on

OS3302, 4 on OS3304])

OFF

SLOW BLINK

FAST BLINK

Port is configured as DOWN.

Port is in data mode.

Port is in handshake mode (looking for a CPE signal).

Port is in training mode (active communication with CPE).

PoE OFF

PoE is turned off.

PoE is turned on.

Ethernet

(0/0 - 0/3)

OFF

Port is linked.

Data is passing over the port.

OnSite 3300 Quick Start Guide 7

3.0 CLI Operation and Configuration

You can connect a PC to configure the OnSite 3300 using the CLI. The 3300 EFM Router comes equipped with an

password protected (easy to use) Command Line Interface. You can connect directly to the unit and make

changes immediately by using the Console Connection or a SSH connection to the default IP address:

192.168.200.10/24. SSH is enabled by default, Telnet is disabled by default for security reasons. In this sec-

tion you can see how easy it is to change IP address, username and save your configuration. On page 9 you can

see a sample configuration for easy connections to Central EFM DSLAM or EFM Peer Router.

3.1 Connect with SSH

1. Connect the Ethernet cable.

2. Connect the power supply.

3. Connect via SSH to the extender through CPE or CO IP addresses

— Default CPE IP address: 192.168.200.10

4. Login with the default username admin and no password.

3.2 Connect with Console

1. Connect the RS232 Console cable. (8-N-1 19200)

2. Connect the power supply.

3. Login with the default username admin and no password.

3.3 Change the IP address (default: 192.168.200.10)

Follow the command sequence below:

node~>enable

node~#configure

node~(cfg)#context ip router

node~(ctx-ip)[router]#interface LAN

node~(if-ip)[router.LAN]#no ipaddress 192.168.200.10/24

node~(if-ip)[router.LAN]#ipaddress <new address>/<new mask>

3.4 Change the default username

The default username will be removed once a new one is created.

Follow the command sequence below:

node~>enable

node~#configure

node~(cfg)#superuser <username> password <password>

3.5 Save the Configuration

Follow the command sequence below:

8OnSite 3300 Quick Start Guide

node~>enable

node~#configure

node~(cfg)#copy running-config startup-config

3.6 OnSite DSL Commands

CO and CPE: This will set the EFM Router as CO or CPE. CO is typically used at the network, CPE is typically

used at the CPE device or CPE network.

node(prt-DSL)# mode {CO|CPE}

Annex Type: Please consult support before changing this setting.

node~(prt-DSL)[<name>]# annex-type { b-g | a-f }

DSL Rate Configuration: This will increase the DSL rate of the OS3300. Your OnSite 3300 is defaulted to

automatically select the optimal rate based on the distance (adaptive).

node(prt-DSL)[0/0]# payload-rate {adaptive [max <192..15296>] |

<192..15296>}

Modulation Scheme: Note higher TC-PAM rates will increase maximum payload rates available but will

decrease distance. Your OnSite 3300 is defaulted to automatically select the optimal setting. Please consult man-

ual for the rate reach chart to determine your optimal setting if you choose to hard set this value. Higher TC-PAM

rates are ideal for shorter cable runs offering max symmetrical (upstream/downstream) speeds of 11.4 Mbps

(TCPAM64) and 15.3 Mbps (TCPAM128) per pair.

node(prt-DSL)[0/0]# tcpam {auto(16/32) | auto(64/128) | 16 | 32 |

64 | 128}

OnSite Ports: The configurations below are used to configure various aspects of the OnSite port(s):

node~(prt-DSL)# port dsl 0 0

Signal to Noise Ratio: Configures the acceptable noise margin for adaptive rate. SNR is the relative strength

of the DSL signal to Noise ratio. 6dB is generally the lowest dB recommended in order for the modem to synch.

As overall bandwidth increases, your signal to noise ratio decreases; the higher the number the better. Your

OS3300 is defaulted at 6 giving you the highest likelihood to connect.

node(prt-DSL)[0/0]# snr-margin <-10..22>

Below 6dB bad

6dB-10dB fair

11dB-20dB good

OnSite 3300 Quick Start Guide 9

Description: This is the description of the port/DSL (OnSite connection). (Ex: "This DSL goes to building 4")

When entering a description with spaces in the text, the description must be in quotations.

node~(prt-DSL)[0/0]# description <description>

Use Profile: Configures the acceptable noise margin for adaptive rate. SNR is the relative strength of the DSL

signal to Noise ratio. 6dB is generally the lowest dB recommended in order for the modem to synch.

node~(prt-dsl)[0/0]# use profile <name>

Service Mode: Configures the number of pairs (wires) you want to use. The OS3300 will default to the max-

imum number of wires available on your version of the OnSite. OS3301 (2-wire); OS3302 (4-wire); OS3304 (8-

wire).

node~(prt-DSL)[0/0]# service-mode { 2-wire | 4-wire | 6-wire | 8-

wire }

Shutdown: Disables or Enables OnSite port(s).

node~(prt-DSL)[0/0]# [no] shutdown

Exit: Return to parent mode.

node~(prt-DSL)[0/0]# exit

Show: Displays all the configured options of the OS3300 OnSite port(s).

node(cfg)# show prt-DSL 0 0

3.7 Sample configuration

Below please find a sample configuration for a typical CPE EFM Router setup. This particular unit is configured as

a DHCP Client on the WAN (EFM) side and DHCP Server configured on the LAN side. It is a simple routed connec-

tion configured to route all default traffic out the DSL WAN port.

10 OnSite 3300 Quick Start Guide

#----------------------------------------------------------------#

# Sample Configuration #

# Patton Electronics Company #

# OS3304 #

# Release: 3.4.2 2014/03/26 #

# Generated configuration file #

# #

#----------------------------------------------------------------#

cli version 4.00

no clock CO default-offset

switch mode groups

profile aaa DEFAULT

method 1 CO continue-on-reject

console

use profile aaa DEFAULT

telnet-server

use profile aaa DEFAULT

shutdown

ssh-server

use profile aaa DEFAULT

no shutdown

snmp-server

shutdown

web-server http

use profile aaa DEFAULT

no shutdown

ntp shutdown

profile napt CO

profile dhcp-server LAN-POOL

network 192.168.200.0/24

lease 24 hours

default-router 192.168.200.10

domain-name-server 8.8.8.8

domain-name-server 8.8.8.4

include 192.168.200.50 192.168.200.100

Profile

profile tls DEFAULT

no authentication incoming

no authentication outgoing

private-key pki:private-key/DEFAULT

own-certificate 1 pki:own-certificate/DEFAULT

Inhaltsverzeichnis

Andere Patton Netzwerk-Router Handbücher

Patton

Patton IPLINK 2800 series Bedienungsanleitung

Patton

Patton SmartNode 4660 Series Bedienungsanleitung

Patton

Patton SL4020 Bedienungsanleitung

Patton

Patton ForeFront 6500 Bedienungsanleitung

Patton

Patton DiamondLink 3201 Bedienungsanleitung

Patton

Patton OnSite 2701A/I Bedienungsanleitung

Patton

Patton SmartNode 4900 Bedienungsanleitung

Patton

Patton SmartNode 5200 Bedienungsanleitung

Patton

Patton OnSite 2603 Bedienungsanleitung

Patton

Patton 2805 Bedienungsanleitung

Patton

Patton SN5300/4B/EUI Bedienungsanleitung

Patton

Patton SmartNode 5300 Bedienungsanleitung

Patton

Patton OnSite 2701A/I Bedienungsanleitung

Patton

Patton ipRocketLink 3101 Series Bedienungsanleitung

Patton

Patton SmartNode 4634 Series Bedienungsanleitung

Patton

Patton BODi rS BD007 Series Bedienungsanleitung

Patton

Patton SmartNode 5400 Series Bedienungsanleitung

Patton

Patton SmartNode 5300 Bedienungsanleitung

Patton

Patton OnSite 2603 Bedienungsanleitung

Patton

Patton SmartNode SN4960 Bedienungsanleitung

Patton

Patton ForeFront 6400 Bedienungsanleitung

Patton

Patton SmartNode 5570 Bedienungsanleitung

Patton

Patton OnSite OS3300 Bedienungsanleitung

Patton

Patton SmartLink 4020 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung