PCE Instruments PCE-DD Series Bedienungsanleitung

PCE Americas Inc.

711 Commerce Way

Suite 8

Jupiter

FL-33458

USA

From outside US: +1

Tel: (561) 320-9162

Fax: (561) 320-9176

[email protected]

www.pce-instruments.com/english

www.pce-instruments.com

PCE Instruments UK Ltd.

Units 12/13

Southpoint Business Park

Ensign way

Hampshire / Southampton

United Kingdom, SO31 4RF

From outside UK: +44

Tel: (0) 2380 98703 0

Fax: (0) 2380 98703 9

[email protected]

Manual

Durometer

PCE-DD Series

A-type durometer applies to general rubber, synthetic rubber, soft rubber,

poly-resin, leather, wax, etc.

C-type durometer applies to rubber and contains the tiny hole material

that that the vesicant is made in being used for plastic

D-type durometer applies to general hard rubber, hard resin, acryl, glass,

thermoplastics, printing plates, fibres, etc.

1.Overview

Shore durometer is used to test hardness of sulfureted rubber and

plastics, such instrument has A-type/D-type/C-type.

A-type and D-type apply to test the low and medium level hardness and

high level hardness of materials.

C-type applies to test the hardness of shoe-making porous materials

made by vesicants within plastics when the compression rate is 50% and

stress is beyond 0.049MPa.

2.Main parameters

Dial value:1-100 degree

Pointer journey:0-2.5mm

Stress at the end of pointer:0.55N-8.06N of A-type and C-type;0-44.5N of

D-type

3.Operationinstructions

Put the sample on a solid plane,hold the durometer to make the pointer

at least 12mm away from the sample edge,and stably put the legs of

durometer on the sample.Thus the pointer straightly goes into the sample till

the legs completely get to the sample.Check the reading in 1s.Repeat shuch

test 5 times at different place which are at least 6mm away from the test

point and find the average reading(the distance between porous materials is

at least 15mm).

4.Notices

Check to make sure before test that figure indicates zero(if not indicates

zero,users may press “ ZERO” key).When press the durometer on the glass

plane,the figure should indicate 100 degree(the top of pointer an its legs

should tightly touch the glass).If it does not indicates ZERO or 100

degree,slightly press the pinter several times;if there is still error,it is

advisable to send it back to the manufacturer.

If it allows,rubber samples should be under the laboratory standard

temperature.If the test result of the sample by A-type durometer goes

beyond 90 degrees,it is advisable to use D-type durometer.When the test of

the sample by D-type durometer goes belw 20 degrees,it is advisable to use

A-type durometer.If the figure on A-type duorometer is below 10 degrees,it is

incorrect and can’t be used.When all the tests are over,users should clean

the gauge,put it back into the box and keep it in a dry place.

Andere PCE Instruments Messgerät Handbücher

PCE Instruments

PCE Instruments PCE-320 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-CT 80-FN2D5 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-P05 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-MMK 1 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-PFM 2 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-VM 40A Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-353 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TG 300 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-RVI 3 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-900 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-N24 Series Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-353N Bedienungsanleitung

PCE Instruments

PCE Instruments UMI 840 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-MSV 10 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-ITM 20 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-T 260 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-SPM 1 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-CT 80 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-DMM 70 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-XXM 30 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-555BT Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-830 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-423 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-VE 1000 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung