PCE Instruments PCE-TG 50 Bedienungsanleitung
PCE Americas Inc.
PCE Instruments UK Ltd.
711 Commerce Way
Units 12/13
Suite 8
Southpoint Business Park
Jupiter
Ensign way
FL-33458
Hampshire / Southampton
USA
United Kingdom, SO31 4RF
From Outside US: +1
From Outside UK: +44
Tel: (561) 320-9162
Tel: (0) 2380 98703 0
Fax: (561) 320-9176
Fax: (0) 2380 98703 9
info@pce-americas.com
info@industrial-needs.com
www.pce-instruments.com/us
www.pce-instruments.com/english
www.industrial-needs.com
Manual
Material Thickness Meter PCE-TG 50
Version 1.0
Date of creation: 03.03.2015
Date of last change: 03.03.2015
Manual
Contents
1 Introduction .............................................................................................................3
2 Safety notes.............................................................................................................3
3 Specification............................................................................................................3
4 System description.................................................................................................4
5 Material selection....................................................................................................4
6 Calibration ...............................................................................................................5
7 Measurement...........................................................................................................5
7.1
Measurement with adjusted velocity speed.................................................................................5
8 Changing the batteries ...........................................................................................5
9 Contact.....................................................................................................................6
9.1
PCE Instruments UK ...................................................................................................................6
9.2
PCE Americas .............................................................................................................................6
2
Manual
3
1 Introduction
Thank you for purchasing a thickness gauge from PCE Instruments.
The PCE-TG 50 is a thickness gauge which stands out because of its small dimensions, the low weight
and its comfortable and easy use. You will be able to use it many years due to its robust casing by simply
following this manual. Read the manual carefully and keep it for potential questions occurring in future.
2 Safety notes
Please read this manual carefully and completely before you use the device for the first time. The device
may only be used by qualified personnel and repaired by PCE Instruments personnel. There is no
warranty of damages or injuries caused by non-observance of the manual.
-
The device may only be used in approved temperature range
-
The opening of the case should only be done by qualified personnel of the PCE Instruments.
-
The instrument should never be placed with the user interface (e.g. keyboard side on a table)
-
You should not make technical changes on the device
-
The appliance should only be cleaned with a damp cloth / use only pH-neutral cleaner
This user's handbook is published from PCE Instruments without any guarantee.
We expressly point to our general guarantee terms, they can be found in our general terms of business.
If you have any questions please contact PCE Instruments.
3 Specification
Display
4 Digits
Measuring range
1,2 …200 mm
Resolution
0,1 mm
Accuracy
±0.5% ±0.1mm
Sound velocity
500 … 9000 m/s
Power supply
4 x 1,5 V AAA batteries
Operation conditions
Temperature: 0 … +50 °C
Rel. Humidity: < 80 %
Rate of measurement
2 measurements per second
Dimensions
140 x 71 x 32 mm
Data output
RS232
Measurement units
mm / inch (selectable)
Weight
Approximately 160 g (incl. batteries)
Delivery content
1 x PCE- TG 50, 1x transportation box, 1 x
ultrasonic sensor, 1 x manual
Manual
4
4 System description
Calibration button
Material select button
Ultrasonic sensor mm / inch button
Minus button Calibration standard
Plus button
Display
Sensor connection
Velocity button
Power button
5 Material selection
Push the power button on the device in order to switch it on. After doing so please push material selection
button and the button will either show “cdxx” or “xxxx”. “cd” stands for code and “xx” gives information on
the material number which ranges from 1 to 11. “xxx” is the adjusted velocity speed of the material that is
to be measured.
No.
Code
Material
1
cd01
Steel
2
cd02
Cast iron
3
cd03
Aluminum
4
cd04
Copper
5
cd05
Brass
6
cd06
Zinc
7
cd07
Quartz glass
8
cd08
PE
9
cd09
PVC
10
cd10
Grey cast iron
11
cd11
Ductile iron
12
xxxx
Velocity speed
Push the plus or minus button to choose a material code and apply the chosen code with the material
selection button. The display will now show “0”. When you choose a code without pushing the material
selection button the device will display “0” after a few seconds, too. If you do not accept a certain code
the settings will not be saved. When pushing the plus button when “cd11” is displayed you will get the
adjustment of the velocity speed. When pushing the minus button when “cd01” is displayed you will also
be able to adjust the velocity speed.
It is essential that you choose the material before the first measurement. Otherwise the measured data
might be incorrect.
Manual
5
6 Calibration
Put some contact paste on the calibration standard and push the calibration button. The display will show
“CAL” now. Now press the sensor on the calibration standard. If the sensor is applied correctly you will
see “((•))” on the display. After that the display will show “CAL” and “5 mm”. If the displayed value is
stable press the calibration button again in order to accept the value and to return to the measuring mode.
You now finished the calibration and the measured value is stored.
7 Measurement
Push the power button to switch on the device and choose your needed unit (mm / inch). Make sure that
the sensor is correctly connected to the device. If that is the case, the device will show “((•))”. Give a bit
of contact paste on the upper side and press the sensor on the material you want to measure. The
measured data will now appear on the display. It is shown as long as a new measurement is made or
until the device is switched off.
7.1
Measurement with adjusted velocity speed
Push the VEL button and the device will show you the last chosen velocity speed. By pushing the plus
and minus buttons you will be able to adjust these. By pressing the button once, the instrument will
change the value by 10 m/s. If a button is pressed for more than four seconds the value will be changed
by 100 m/s.
Put some contact paste on the material you want to measure and press the sensor on it. The measured
data will be displayed.
In case you should not know what material is to be measured take a caliper, measure the thickness on
one side and note the thickness. Also note the velocity speed that is adjusted. Now take the thickness
gauge and change the velocity speed as long as the measured value is the same value that you wrote
down. Now write down the velocity speed for that material. If you are willing to perform additional
measurements you will have to change the velocity speed before those measurements.
8 Changing the batteries
If the voltage is to low, the thickness gauge will show a battery sign on the display. To change the battery
open the battery lid, and replace the old batteries.
Manual
6
9 Contact
If you have any questions about our range of products or measuring instruments please contact PCE
Instruments.
9.1
PCE Instruments UK
By post:
PCE Instruments UK Ltd.
Units 12/13 Southpoint Business Park
Ensign Way, Southampton
Hampshire
United Kingdom, SO31 4RF
By phone:
Support: 02380 987 035
Sales: 02380 987 030
9.2
PCE Americas
By post:
PCE Americas Inc.
711 Commerce Way
Suite 8
Jupiter
33458 FL
USA
By phone:
Phone: 410-387-7703
Fax: 410-387-7714
Andere Handbücher für PCE-TG 50
1
Inhaltsverzeichnis
Andere PCE Instruments Messgerät Handbücher
PCE Instruments
PCE Instruments PCE-AQD 50 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-HDM 20 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-DC1 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-320 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-N24 Series Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-VT 3800 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-172 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-228LIQ Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-TDS 200 Series Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-127 Series Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-WMT 200 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-USC 20 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-VA 10 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-DFG X Series Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-PA 8000 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-VA 20 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-TDS 200 Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-TG 300-P5EE Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-DFG 500 Series Bedienungsanleitung
PCE Instruments
PCE Instruments PCE-TG 300-NO2-ICA Bedienungsanleitung
