PCE Instruments PCE-TG200 Bedienungsanleitung

INSTRUCTION MANUAL

PCE-TG200

PCE Americas Inc.

711 Commerce Way

Suite 8

Jupiter

FL-33458

USA

From outside US: +1

Tel: (561) 320-9162

Fax: (561) 320-9176

[email protected]

www.pce-instruments.com/english

www.pce-instruments.com

PCE Instruments UK Ltd.

Units 12/13

Southpoint Business Park

Ensign way

Hampshire / Southampton

United Kingdom, SO31 4RF

From outside UK: +44

Tel: (0) 2380 98703 0

Fax: (0) 2380 98703 9

[email protected]

Material-Thickness-Meter

CONTENTS

1. Switch on........................................................................................................................................................... 3

2. Backlight on / off............................................................................................................................................... 3

3. Measurement..................................................................................................................................................... 3

4. Calibration......................................................................................................................................................... 3

5. Set-up................................................................................................................................................................. 3

a. Measurement ................................................................................................................................................. 4

b. Velocity Rate .................................................................................................................................................. 4

c. Probe Setting.................................................................................................................................................. 4

d. Resolution ...................................................................................................................................................... 4

e. Memory........................................................................................................................................................... 5

f. Limitation ......................................................................................................................................................... 5

g. Average Measurement ................................................................................................................................... 5

h. Print Out ......................................................................................................................................................... 5

i. Default ............................................................................................................................................................. 6

6. Data print-out (optional)................................................................................................................................... 6

7. Technical data................................................................................................................................................... 6

8. Appendix ........................................................................................................................................................... 7

c- ON/OFF

- ESC

d- Change Setting

- Calibration

e- Menu

- Confirm

f- Store Data

g- Increase Symbolized Number

- Backlight Switch

h- Re-read Data

1. Switch on

Press key to turn on the gauge. The gauge will consecutively display

- Logo

- Serial No. and software version then the gauge will enter into measuring mode and display

- 0.0mm/0.00mm(0.00IN/0.000IN depending on the last used)

- Velocity rate and selected probe

- Location Lumber

2. Backlight on / off

Press key, the backlight is on. Press key again, the backlight is off.

3. Measurement

There are three ways to go into measuring mode:

- Switch on the gauge;

- Press power key escape from MENU;

- Measurement.

4. Calibration

When initially switch on the gauge or get an error value instead of 4.00mm (when velocity rate is 5920 m/s) if

take measurement of test block attached on the gauge (which correct value should be 4.00mm) or other

standard test block, the gauge needs to be calibrated simply by pressing key. The gauge will display same

information and operate according to this information, then the gauge will automatically calibrate.

5. Set-up

Press key, the gauge will display:

1. Measurement

2. Velocity Rate

3. Probe Setting

4. Resolution

5. Memory

6. Limitation

7. Average Measurement

8. Print Out

9. Default

a. Measurement

- No Contents

b. Velocity Rate

b-1. Setting velocity

- Press key into“ Setting velocity ”state

- Press or to change velocity rate

- Press to enter/confirm

b-2. Velocity measurement

- Measuring the sample which thickness is known

- Press key into“ Velocity measurement ”state

- Press or to up and down the value of velocity to determine the thickness as the same as the value

of sample that is measured

- Press key again, the gauge will store the velocity rate automatically.

c. Probe Setting

The gauge provides three types of probe for user.

- Press key into “Probe selecting” state

- Press or to select probe.

1= normal probe (PT-08)

2= small diameter probe (PT-06)

3= low frequency probe (ZT-12)

4= High Temperature probe (GT-13)

- Press key to enter/confirm

d. Resolution

- Press key into “Resolution” state

- Press or to select resolution and unite.

1= 0.1 mm

2= 0.01 mm

3= 0.01 IN

4= 0.001 IN

- Press key to enter/confirm

e. Memory

e-1. Location

The gauge has a memory capacity of 4000 measurements which location can be from 0000 to 3999. After

taking every measurement, press key to store the value with a location number. You can also select an

initial number for beginning to store the value and the next number will be followed automatically by following

measurements.

- Press key into“ Location ”state

- Press or to select desired number as initial location

- Press key to enter/confirm

If you want to read the stored value in memory,

Press key to read one by one data according to the above procedure, select desired initial number. Then

the desired group of value can be readable beginning from this initial number.

e-2. Delete Memory

Delete the data in memory which locations are selected.

f. Limitation

- Press key into“ Limitation ”state

- Press or to select desired low limitation and high limitation

- Press key to enter/confirm

When the measuring value is lower or higher than the limit value a sign “L” or “H” will appear on the right top of

LCD.

g. Average Measurement

You can get mean values by 2 to 9 times on TG 200 thickness gauge

- Press key into “ Average ”state

- Press to select desired average times (2 to 9)

- Press key to enter/confirm

When complete measuring once, you must wait about 3 seconds, the gauge will calculate measuring data and

average times will decrease 1 appearing on the right top of LCD. When average times is zero, the gauge will

show the averaged value on LCD.

h. Print Out

If you want to print the stored values, you must determent the initial location number and the end location

number,

- Press key into “Print” state

- Press or to select desired initial and end location number.

- Press key to enter / confirm

The gauge will print the stored value in memory from initial location number to end location number

automatically.

i. Default

When you select “Default” state, the gauge will recover the default parameter.

6. Data print-out (optional)

This procedure is almost like “Print”, but mini-printer replaced by PC.

- Press key into “Print” state

- Press or to select desired initial and end location number.

- Press key to enter / confirm

The stored value in memory will transfer into PC.

7. Technical data

Display unite: 128×32 LCD with backlight

Measuring rate: 2Hz

Velocity rate: 1000 ~ 9999 m/s

0.0393 ~ 0.3936 inch/μs

Measuring range: 0.65 ~ 250.0 mm

0.026 ~ 9.843 inches

Resolution: 0.1 mm 0.01 mm or 0.01 inch 0.001 inch

Tolerance: 0.65 ~ 9.99 mm±0.04 mm

10 ~ 99.99 mm ±(0.1%+0.04) mm

100 ~ 250 mm ±0.3%

Power supply: two 1.5V AAA dry cells

Size: 61×108×28 mm³ (w×h×d)

Weight: 150g with batteries

Operating temperature: -10 ºC to +50 ºC

Storage temperature: -20 ºC to +60 ºC

Probe types and measuring rang:

Standard probe: PT-08 5.0MHz measuring rang: 0.8 - 200 mm

Miniature probe: PT-06 7.5MHz measuring rang: 0.7 - 50 mm

Lowe frequency probe: ZT-12 2.0MHz measuring rang: 2.0 - 250 mm

High temperature probe: GT-13 5.0MHz measuring rang: 3.0 – 100 mm

8. Appendix

Velocity rate of various materials

Material V (m/s) V (in/us)

Aluminium 6400 0.252

Brass 4700 0.185

Copper 5010 0.197

Glass 5260-6120 0.207-0.241

Lucite 2680 0.105

Nickel 6040 0.237

Nylon 2730 0.103

Polyethylene 1950 0.070

Polystyrene 2350 0.092

Steel 5920 0.233

Stainless Steel 5740 0.226

Titanium 5990 0.237

Water 1490 0.059

Zinc 4210 0.165

NOTE: "This instrument doesn’t have ATEX protection, so it should not be used in potentially explosive

atmospheres (powder, flammable gases)."

Inhaltsverzeichnis

Andere PCE Instruments Messgerät Handbücher

PCE Instruments

PCE Instruments PCE-RS 27 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-HWA 30-ICA Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-172 Bedienungsanleitung

PCE Instruments

PCE Instruments CP Series Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-MSM 4 Bedienungsanleitung

PCE Instruments

PCE Instruments Schiltknecht MiniAir 20 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-WMM 50 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-EM 29 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-GPA 62 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-EM 883 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-SPM 1 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-MAM 2 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-COG 10 Bedienungsanleitung

PCE Instruments

PCE Instruments LMD 5 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-N24 Series Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-320 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-TDS 200 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-PH 23 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-LDM 45 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-HT 70-ICA Bedienungsanleitung

PCE Instruments

PCE Instruments IT55 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-WMT 200 Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-HWA 20BT Bedienungsanleitung

PCE Instruments

PCE Instruments PCE-228 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung