Peavey TransTube Bandit 112 Bedienungsanleitung

S E R I E S

”

ETM

AIntended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufficient magnitude to constitute a risk of electric shock to persons.

AIntended to alert the user of the presence of important operating and maintenance (servicing) instructions in the

literature accompanying the product.

CAUTION: Risk of electrical shock - DO NOT OPEN!

CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to

qualified service personnel.

WARNING: To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture. Before using this

appliance, read the operating guide for further warnings.

AEste simbolo tiene el prop6sito de alertar al usuario de la presencia de “(voltaje) peligroso” que no tiene

aislamiento dentro de la caja de1 product0 que puede tener una magnitud suficiente coma para constituir riesgo de

corrientazo.

AEste simbolo tiene el prop6sito de alertar al usario de la presencia de instruccones importantes sobre la operaci6n

y mantenimiento en la literatura que viene con el producto.

PRECAUCION: Riesgo de corrientazo - No abra.

PRECAUCION: Para disminuir el riesgo de corrientazo, no abra la cubierta. No hay piezas adentro que el usario pueda

reparar. Deje todo mantenimiento a 10s t&cnicos calificados.

ADVERTENCIA: Para evitar corrientazos o peligro de incendio, no deje expuesto a la lluvia o humedad este aparato

Antes de usar este aparato, lea m8s advertencias en la guia de operaci6n.

ACe symbole est utilisk pur indiquer

l’utilisateur la presence B l’interieur de ce produit de tension non-isolee

dangereuse pouvant

ctre

d’intensitk suffisante pour constituer un risque de choc klectrique.

ACe symbole est utilis6 pour indiquer

l’utilisateur qu’il ou qu’elle trouvera d’importantes instructions sur

l’utilisation et l’entretien (service) de l’appareil dans la littkrature accompagnant le produit.

ATTENTION: Risques de choc electrique - NE PAS OUVRIR!

ATTENTION: Afin de riduire le risque de choc klectrique, ne pas enlever le couvercle. I1 ne se trouve

l’intkrieur

aucune pi&e pouvant etre

r6par6e

par l’utilisateur. Confier l’entretien

un personnel qualifik.

AVERTISSEMENT: Afin de prevenir les risques de dkcharge ilectrique ou de feu, n’exposez pas cet appareil

la pluie

I’humidite. Avant d’utiliser cet appareil, lisez les avertissements suppl6mentaires situ& dans le guide.

ADieses Symbol sol1 den Anwender vor unisolierten gefghrlichen Spannungen innerhalb des Gehguses warnen, die

von Ausreichender

Stgrke

sind, urn einen elektrischen Schlag verursachen zu kiinnen.

ADieses Symbol sol1 den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die

Handhabung und Wartung des Produkts betreffen.

VORSICHT: Risiko - Elektrischer Schlag! Nicht iiffnen!

VORSICHT: Urn das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden sich

keine Teile darin, die vom Anwender repariert werden kiinnten. Reparaturen nur von qualifiziertem Fachpersonal

durchfiihren lassen.

ACHTUNG: Urn einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte dieses

Ger%t

nicht dem Regen oder

Feuchtigkeit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

Congratulations on your purchase of the all new Bandit@ 112

TransTubeTM

Series. This amp represents

years of research on vacuum tube emulation, resulting in a totally new Bandit. The preamp has been rede-

signed, using patent-applied for technology that redefines tubelike distortion and harmonic generation in

solid-state amps.

The new TTM Dynamics circuitry, also awaiting several patents, creates the long sought for tube power

compression phenomenon. This, in combination with resonance and presence circuitry, yields the closest

tube amp simulation to date. This compression effect is increased by turning the T. Dynamics control down,

which lowers the power level the amp puts out.

To further enhance the performance of the Bandit, an added external speaker jack increases the power to

100 watts, and a footswitchable effects loop allows for greater flexibility.

FRONT PANEL FEATURES

HIGH GAIN INPUT (1)

Used for most electric guitars. It is 6 dB louder than Low Gain input.

LOW GAIN INPUT (2)

Provided for instruments that have extremely high outputs, which can result in overdriving (distorting) the

High Gain input. If both inputs are used simultaneously, the output levels are the same (both are Low Gain).

VOLUME (3)

Controls the volume level of the Clean channel.

BRIGHT SWITCH (4)

Provides a preset boost (6 dB) to treble frequencies. To activate, depress the switch to its “in” position.

CHANNEL SELECT SWITCH (5)

Allows selection of the Lead or Clean channel. The “in” position of the switch selects the Lead channel and

the “out” position selects Clean.

NOTE: Channel selection may also be achieved by the remote footswitch. If remote selection is desired, the

channel switch must be in the “in” (Lead) position.

LOW, MID, & HIGH EQ (6)

Passive tone controls that regulate the low, mid, and high frequencies of the Clean channel.

PRE GAIN (7)

Controls the input volume level of the Lead channel.

THRASH SWITCH (8)

Notches the mid range about 20 dB.

GAIN SWITCH (9)

Boosts the overall system gain. Depress to the “in” position to activate.

LOW, MID,

HIGH EQ (10)

Passive tone controls that regulate the low, mid, and high frequencies of the Lead channel.

POST GAIN (11)

Controls the overall volume level of the Lead channel. The final level adjustment should be made after the

desired sound has been achieved.

REVERB LEVEL (12)

Controls the overall reverb level.

EFFECTS SEND (13)

Output for supplying signals to external low-level effects or signal processing equipment.

EFFECTS RETURN (14)

Input for returning signals from external low-level effects or signal processing equipment.

EFFECTS LEVEL SWITCH (15)

Selects the effects loop operating level: -10 dBV (0.3 V RMS) when “out” and 0 dBV (1 V RMS) when “in.”

RESONANCE SWITCH (16)

Used to fine-tune the low frequency range of the speaker enclosure by varying the damping factor of the

amplifier between two presets.

PRESENCE (17)

An active tone control that boosts the extreme high frequencies by 6 dB.

TTM DYNAMICS CONTROL (18)

Adjusts the power level of the amplifier from 10 percent to 100 percent power. When set to lower settings,

the power compression simulation will be much more pronounced.

POWER LED (19)

Illuminates when AC power is being supplied to the amp

POWER SWITCH (20)

Depress the switch to the “on” position. The red pilot light (LED) will illuminate indicating power is being

supplied to the unit.

Back Panel:

BACK PANEL FEATURES

GROUND SWITCH (21)

Three position rocker-type switch, which, in most applications, should be operated in its center or zero

position. There may be some situations when audible hum and/or noise will come from the loudspeaker. If

this situation arises, position the ground switch to either positive or negative (+ or -) or until the noise is

minimized.

NOTE: Should the noise problem continue, consult your Authorized Peavey Dealer, the Peavey Factory, or a

qualified service technician. THE GROUND SWITCH IS NOT FUNCTIONAL ON 220/240 VOLT MODELS.

LINE CORD-120 V products only (22)

AFor your safety, we have incorporated a three-wire line (mains) cable with proper grounding

facilities. It is not advisable to remove the ground pin under any circumstances. If it is neces-

sary to use the equipment without proper grounding facilities, suitable grounding adaptors

should be used. Less noise and greatly reduced shock hazard exists when the unit is oper-

ated with properly grounded receptacles.

EXTERNAL SPEAKER JACK (23)

AProvided for connection of external speaker cabinet. Minimum external speaker impedance

is 8 ohms (4 ohm total impedance).

REMOTE SWITCH JACK (24)

Provided for the connection of the supplied remote footswitch. The footswitch is used to select the Lead or

Normal channels and defeat effects loop. When using remote footswitch, always insert the plug fully (second

click) to insure proper operation.

POWER AMP INPUT (25)

Used to connect line level signal to the power amplifier.

PREAMP OUT (26)

The preamp out can be used to route the amplified signal to a mixing console, tape recorder, etc. Connect

the preamp output using a shielded cable to an input of the tape recorder, mixer, etc. This patch does not

affect the operation of the amplifier.

SPECIFICATIONS

Rated Power & Load:

Power specs measured with T. Dynamics @ IO

80 W RMS into 8 ohms

100 W RMS into 4 ohms

Power @ Clipping: (typically)

(5% THD, 1 kHz, 120 V AC line)

80 W RMS into 8 ohms

100 W RMS into 4 ohms

Frequency Response:

+O, 3 dB, 60 Hz to 20 kHz, @ 65 W RMS

into 8 ohms

Hum & Noise:

Greater than 86 dB below rated power

Power Consumption:

300 W

50/60 Hz, 120 V AC, Domestic

300 W @ 60 Hz, 220-230/240 V AC, Export

PREAMP SECTION

The following specs are measured @ 1 kHz with the controls

preset as folio ws:

Push Bright, Off (Out)

Channel Select Normal (Out)

Low & High @ IO

Mid @ 0

Presence @ 0 dB

Pre 5: Post Gain @ IO

Gain 6: Thrash, Off (Out)

Normal Levels are with normal volume @ 5

Minimum Levels are with normal volume @ 10

Preamp High Gain Input:

Impedance: High-Z, 1 M ohm

Nominal Input Level: -14 dBV, 200 mV RMS

Minimum Input Level: -24 dBV, 60 mV RMS

Maximum Input Level: 0 dBV, 1 V RMS

Preamp Low Gain Input:

Impedance: High-Z, 44 K ohms

Nominal Input Level: -8 dBV, 400 mV RMS

Minimum Input Level: -18 dBV, 120 mV RMS

Maximum Input Level: 6 dBV, 2 V RMS

Effects Send:

Load Impedance: 1 K ohm or greater

Nominal Output Level: -10 dBV, 0.3 V RMS or

0 dBV, 1 V RMS if Effects Level is in

Effects Return:

Impedance: High-Z, 22 K ohms

Designed Input Level: -10 dBV, 0.3 V RMS or

0 dBV, 1 V RMS if Effects Level is in

(Switching jack provides Effects Send to Effects

Return connection when not used)

Preamp Output:

Load Impedance: 1 K ohm or greater

Nominal Output Level: 0 dBV, 1 V RMS

Power Amp Input:

Impedance: High-Z, 30 K ohms

Designed Input Level: 0 dBV, 1 V RMS

(Switching jack provides preamp output to power

amp input connection when not used)

System Hum & Noise

Nominal Input Level:

(20 Hz to 20 kHz unweighted)

72 dB below rated power

Equalization:

Special low, mid, & high passive type EQ

Presence: +6 dB @ 5 kHz

Push Bright: +6 dB @ 2 kHz

Push Thrash: -20 dB notch @ 1 kHz in Lead

channel

Push Gain: Increases Lead gain

Push Resonance: +6 dB @ cabinet resonance

External Footswitch Functions:

Lead Channel Defeat (when selected with button)

Effects Loop Bypass

Dimensions & Weight:

20.0” H x 23.375” D x 11.25” D

46.5 Ibs.

T Dynamics R.O.C. Invention Patent No. 072727

~features

and Due to our eflorts for constant improvements,

specifications listed herein are subject to change without

Tone Settings

Adjust to

“IN” “IN”

Preference

CLEAN

METAL

“OUT” “OUT”

Adjust to

Preference

“OUT”

“IN”

JAZZ MEDIUM

DISTORTION

“OUT” “OUT”

HIGH LOW

PHESENCE

DYNAMICS

GAIN GAIN

,NP”TS

CLEAN LEAD REVERB

LOOP

POWER AMP

“OUT”

CLEAN DIRTY

BLUES BLUES

Consulte 10s diagramas de1 panel

delantero en la seccih de ingl6s de este manual.

Felicitaciones por la adquisicion del nuevo miembro de la serie TransTube, el amplificador Bandit@ 112. Este

novisimo amplificador representa adios de investigation en el campo de la emulation del sonido generado

por 10s tubos de vacio. El preamplificador ha sido redisefiado utilizando una tecnologia en proceso de

patentacion que redefine la distorsion similar a la creada por 10s tubos de vacio y la generation armonica en

10s amplificadores transistorizados.

El nuevo circuit0 T

Dynamics, tambien en proceso de patentacion, crea el tan codiciado fenomeno de

compresion de potencia que generaban 10s tubos de vacio. Esto, ademas del circuit0 de resonancia y

presencia, produce la simulacicn de amplificador con tubos de vacio

m&s

fiel que se haya logrado hasta la

fecha. Ademas, se puede aumentar el efecto de compresion al bajar el control del circuit0 T. Dynamics, con

lo cual se reduce el nivel de potencia que genera el amplificador.

Para un desempefio atin mejor, el amplificador Bandit cuenta con un enchufe para altavoz externo que

aumenta la potencia a 100 watts y un circuit0 de efectos conmutables por pedal para lograr mas flexibilidad.

FUNCIONES DEL TABLERO FRONTAL

HIGH GAIN INPUT (Entrada de ganancia alta) (1)

Se usa para la mayoria de las guitarras electricas. Tiene 6 dB mas volumen que la entrada de baja

ganancia.

LOW GAIN INPUT (Entrada de baja ganancia) (2)

Se suministra para instrumentos que tienen una salida extremadamente alta, la cual puede causar la

sobrecarga (distorsion) de la entrada de alta ganancia. Si se usan ambas entradas simultaneamente, el

nivel de salida es el mismo (ambos son de baja ganancia).

VOLUME (El volumen) (3)

Controla el nivel de volumen del canal “clean”.

BRIGHT SWITCH (Interruptor de brillo) (4)

Proporciona un impulso preajustado de +6 dB a las frecuencias agudas. Para activarlo, empuje el

interruptor a la position “hacia dentro”.

CHANNEL SELECT SWITCH (Interruptor para seleccih del canal) (5)

Permite la selection del canal “lead” (solista) o “clean.” La position hacia dentro selecciona el canal “lead” y

la position hacia fuera selecciona el canal “clean”.

NOTA: Tambien se puede lograr la selection del canal por medio del pedal interruptor remoto. Si desea la

selection a control remoto, el interruptor de canal debe estar en la position “in” (hacia adentro) (canal de

solista).

LOW, MID, & HIGH EQ (Ecualizador de frecuencias graves, medias, y agudas) (6)

Controles de tono pasivo que regulan las frecuencias graves, medias, y altas del canal “clean”.

PRE GAIN (Control del preamplificador) (7)

Controla la entrada de volumen del canal solista.

THRASH (Conmutador de batido) (8)

Recorta la escala media en casi 20 dB.

GAIN SWITCH (Interruptor de ganancia) (9)

Proporciona impulso a la ganancia general del sistema. Para activarlo oprimalo a la position “in” (hacia

adentro).

LOW, MID, & HIGH EQ (Ecualizador de frecuencias graves, medias, y agudas) (10)

Controles de tono pasivo que regulan las frecuencias graves, medias, y altas del canal solista.

POST GAIN (Control de ganancia posterior del preamplificador) (11)

Controla el volumen general del canal solista. El ajuste final de nivel debe hacerse despues de que se haya

obtenido el sonido deseado.

REVERB LEVEL (Nivel de reverberation) (12)

Controla el nivel global de la reverberation.

EFFECTS SEND (Envio de efectos) (13)

Salida para proporcionar senales a efectos exteriores de bajo nivel o a equipos procesadores de serial.

EFFECTS RETURN (Retorno de efectos) (14)

Entrada para el retorno de seiiales procedentes de equipos de efectos externos de bajo nivel o de

procesadores de serial.

EFFECTS LEVEL SWITCH (Conmutador de nivel de efectos) (15)

Selecciona el nivel operational del circuit0 de efectos: -10 dBV (0.3 V RMS) cuando esta “afuera” y a 0 dBV

(1 V RMS) cuando esta “adentro”.

RESONANCE SWITCH (Conmutador de resonancia) (16)

Utilizado para realizar ajustes precisos del rango de frecuencias bajas de la caja de altavoces a traves de la

variation del factor de amortiguacion de las frecuencias bajas del amplificador entre dos posiciones

predeterminadas.

PRESENCE (Presencia) (17)

Control de tono active que aumenta en 6 dB las frecuencias de 10s extermos agudos.

TTM DYNAMICS CONTROL (Control del circuit0 T Dynamics) (18)

Ajusta el nivel de potencia del amplificador de 10% a 100%. Cuando esta en la position mas baja, la

simulation de compresion de potencia sera mas pronunciada.

POWER LED (LED indicador de corriente) (19)

Se ilumina cuando el amplificador recibe corriente alterna.

POWER SWITCH (Interruptor de corriente) (20)

Oprima el interruptor a la position “hacia dentro” (encendido). La luz roja del pilot0 (indicador) se encendera

indicando que la unidad esta recibiendo corriente alterna.

Inhaltsverzeichnis

Sprachen:

Andere Peavey Verstärker für Musikinstrumente Handbücher

Peavey

Peavey Windsor Studio Bedienungsanleitung

Peavey

Peavey Ecoustic E20 Bedienungsanleitung

Peavey

Peavey TKO 65 Bedienungsanleitung

Peavey

Peavey Tour TNT 115 Bedienungsanleitung

Peavey

Peavey Stereo Chorus 212 Bedienungsanleitung

Peavey

Peavey Ecoustic 112 Bedienungsanleitung

Peavey

Peavey Rage 258 Bedienungsanleitung

Peavey

Peavey TNT 115S/BW Bedienungsanleitung

Peavey

Peavey Classic 20 Bedienungsanleitung

Peavey

Peavey KB2 Bedienungsanleitung

Peavey

Peavey Classic 30 Bedienungsanleitung

Peavey

Peavey TNT 160 Bedienungsanleitung

Peavey

Peavey Blazer 158 Bedienungsanleitung

Peavey

Peavey Basic 50 Bedienungsanleitung

Peavey

Peavey PV i 8500 Bedienungsanleitung

Peavey

Peavey Backstage backstage Bedienungsanleitung

Peavey

Peavey BACKSTAGE 50 Bedienungsanleitung

Peavey

Peavey VTM-120 Bedienungsanleitung

Peavey

Peavey Studio Pro 110 Bedienungsanleitung

Peavey

Peavey EVH 5150 II Bedienungsanleitung

Peavey

Peavey TKO Bedienungsanleitung

Peavey

Peavey JSX JSXTM Mini ColossalTM Class A Tube Guitar... Bedienungsanleitung

Peavey

Peavey The Classic Bedienungsanleitung

Peavey

Peavey Firebass 700 Bedienungsanleitung

Beliebte Verstärker für Musikinstrumente Handbücher anderer Marken

acus

acus One Forstreet 10 Bedienungsanleitung

Marshall Amplification

Marshall Amplification MG10KK Bedienungsanleitung

Pyle Pro

Pyle Pro PPG860A Bedienungsanleitung

Laney

Laney BC30 Bedienungsanleitung

Vox

Vox Pathfinder 15SMR Bedienungsanleitung

Marshall Amplification

Marshall Amplification JVM205C Bedienungsanleitung

Crate

Crate Professional BV-120H Bedienungsanleitung

Fender

Fender Bassman 1200 Bedienungsanleitung

ZT Club Bedienungsanleitung

Ibanez

Ibanez IFS2X Bedienungsanleitung

Crate

Crate GLX1200H Bedienungsanleitung

Laboga

Laboga THE BEAST Bedienungsanleitung

Falken1

Falken1 Traveller Pro Bedienungsanleitung

Hughes & Kettner

Hughes & Kettner Bass Kick 303 Bedienungsanleitung

Yamaha

Yamaha GA-10 Bedienungsanleitung

Engl

Engl Powerball-2 Service-Handbuch

Gibson

Gibson GA5WTR Kurzanleitung

Engl

Engl Powerball-2 Bedienungsanleitung