PEERLESS Mounts FPECMC-01 Leitfaden

Installation and Assembly:

Concrete Ceiling Mount for Peerless®Outdoor Enclosures*

Models: FPECMC-01, FPECMC-02,

FPECMC-03, FPECMC-04

Max Load Capacity: 400 lb (181 kg)

ISSUED: 08-09-10 SHEET #: 061-9058-4 10-18-10

*For use with Peerless®Outdoor Enclosures only

2 of 24 ISSUED: 08-09-10 SHEET #: 061-9058-4 10-18-10

NOTE: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Solid Concrete..................................................................................................................................................4

Installing Tilt Plate to Main Enclosure Assembly ....................................................................................................................6

Mounting Main Enclosure Assembly.......................................................................................................................................7

Tools Needed for Assembly

• 6mm allen wrench, 3/16" allen wrench

• drill

• 3/8" (10mm) bit for solid concrete

• level

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Due to outdoor environmental conditions such as strong wind gusts, heavy snow, hail, rain, etc. The environmental

enclosure mount, together with the enclosure, extension tube and hardware, must be inspected at least once a

year, and immediately following any time winds exceed 90 mph. A qualiﬁed installer or inspector must check for

signs of rust, loose fasteners, bent metal, etc. If evidence of excessive wear, deterioration or any unsafe condition

is observed, this product must be taken out of service immediately. Direct all inquiries to customer care if you have

any questions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product was designed for use with other outdoor products only.

WARNING

3 of 24 ISSUED: 08-09-10 SHEET #: 061-9058-4 10-18-10

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

Description Qty. Part # Model # Part #

Aadapter box 1061-7350 FPECMC-01 061-7368

Btilt plate 1061-7351 FPECMC-02 061-7369

Cceiling assembly 1061-7353 FPECMC-03 061-7370

Dsupport column 1see chart FPECMC-04 061-7371

EM10 x 16mm socket screw 4 520-5013

Fsplit lock washer 4540-5001

G1/4"-20 x 3/4" socket cap screw 6 520-5034

H1/4"-20 nylock nut 6530-5007

Iu-bolt with hex nuts 2 520-5037

Jcarriage bolt 3 520-5039

K3/8"-16 nylock nut 3 530-5004

Lconcrete expansion anchor 6 5M9-381-H03

M5mm washer 6 540-5014

Parts List Support Tube (D)

4 of 24 ISSUED: 08-09-10 SHEET #: 061-9058-4 10-18-10

Use ceiling plate (C) as a template to mark six mounting holes on concrete ceiling. Drill six 3/8" (10 mm) dia. pilot

holes to a minimum depth of 3". Place concrete expansion anchors (L) into ceiling and tighten to secure. Remove

bolt and washer from anchor housing. Place ceiling plate over anchors and secure with bolt and washer from

anchor housing. Tighten all fasteners.

Installation to Solid Concrete surface

• Concrete must be 3000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

WARNING

• Tighten screws so that ceiling assembly is ﬁrmly

attached, but do not overtighten. Overtightening

can damage screws, greatly reducing their holding

power.

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material.

WARNING

CONCRETE

SURFACE

BOLT (L)

WASHER (L)

Drill 3/8" (10 mm) dia. holes.

Tap concrete expansion anchors (L) into holes.

Tighten concrete expansion anchors (L) to secure to wall.

Unscrew bolt and washer from anchor housing, level wall plate (C)

on wall, and secure. Do not tighten in excess of 80 in•lbs (9.0 N.m.).

concrete

surface

CUTAWAY VIEW

5 of 24 ISSUED: 08-09-10 SHEET #: 061-9058-4 10-18-10

Insert two M10 x 16 mm socket screws (E) and

two split lock washers (F) into bottom of adapter

box (A) leaving 1/4" exposed thread as shown in

ﬁgure 2.1 and detail 1.

Unscrew hex nuts from u-bolts (I). Secure adapter

box (A) to support column (D) with two u-bolts (I)

and two hex nuts.

Adjust swivel of adapter box as shown and tighten

all fasteners.

Insert one 3/8-16 x 4" ﬂat head bolt (J) through

bottom hole of support column (D) and secure with

3/8" nylock nut (K).

Set adapter box (A) onto support column (D).

Insert support column (D) into ceiling assembly

(C). Align holes of support column with holes of

ceiling assembly and secure using two 3/8-16 x 4"

ﬂat head bolts (J) and two 3/8" nylock nuts (K).

DETAIL 1

ﬁg. 2.1

1/4"

HEX NUTS (I)

6 of 24 ISSUED: 08-09-10 SHEET #: 061-9058-4 10-18-10

NOTE: Follow instructions with main enclosure assembly for removal of bay door and vertical brackets.

Thread six 1/4-20 x .75" socket cap screws (G) with washers (M) through tilt plate (B), main enclosure assembly

(sold separately), seal washer (provided with enclosure assembly), and nylock nut (H) as shown below. Tighten all

fasteners using a 3/16" allen wrench.

Installing Tilt Plate to Main Enclosure Assembly

• Tighten screws so tilt plate (B) is ﬁrmly attached. Do not tighten with excessive force. Overtightening can cause

stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

WARNING

SEAL WASHERS

MAIN ENCLOSURE

ASSEMBLY

MAIN ENCLOSURE ASSEMBLY MAY APPEAR SLIGHTLY

DIFFERENT THAN ILLUSTRATED - SHOWN WITHOUT

BAY DOOR AND VERTICAL BRACKETS

7 of 24 ISSUED: 08-09-10 SHEET #: 061-9058-4 10-18-10

All other brand and product names are trademarks or registered trademarks of their respective owners.

Hook tilt plate (B) onto bottom socket screws

threaded into adapter box (A) and select desired

tilt angle (0° to 20°) as shown in ﬁgure 7.1. NOTE:

Be sure split lock washer (F) is on outside of tilt

plate as shown in detail 2.

Insert two M10 x 16 mm socket screws (E) and

two split lock washers (F) through tilt plate (B) and

into top of adapter box (A) as shown in ﬁgure 7.2.

Tighten all fasteners using 6 mm allen wrench.

Mounting Main Enclosure Assembly

• Do not lift more weight than you can handle. Always use an assistant or mechanical lifting equipment to safely lift

and position the ﬂat panel screen.

• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to

40 in. • lb (4.5 N.M.) maximum torque.

WARNING

• Do not allow main enclosure assembly to hang freely

on wall box (A) when all four sets of M10 x 16 mm

socket screws (E) are not fully secured or mount may

come off of wall.

CAUTION

ﬁg 7.1

ﬁg 7.2

MAIN ENCLOSURE

ASSEMBLY

DETAIL 2

Instalación y Ensamblaje:

Soporte para techos de concreto para cajas protectoras para

exteriores* Peerless®

Modelos: FPECMC-01, FPECMC-02,

FPECMC-03, FPECMC-04

Capacidad de Carga Máxima: 400 lb (181 kg)

ISSUED: 08-09-10 SHEET #: 061-9058-4 10-18-10

*Para cajas protectoras para exteriores* Peerless solamente

9 de 24 PUBLICADO: 08-09-10 HOJA #: 061-9058-4 10-18-10

Español

Contenido

Lista de piezas..................................................................................................................................................................... 10

Instalación en un techo de concreto ....................................................................................................................................11

Instalar la placa inclinable a la unidad principal de la caja protectora................................................................................. 13

Instalar unidad principal de la caja protectora..................................................................................................................... 14

NOTA: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.

• No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias

contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las ad-

vertencias, por favor, llame a Servicio al Cliente de Peerless al 1-800-865-2112 si está en EE. UU. Si es un cliente

internacional, por favor, comuníquese con su distribuidor local.

• Este producto sólo debe ser instalado por una persona que tenga una buena aptitud mecánica, que tenga

experiencia en construcción básica de ediﬁcios y que entienda estas instrucciones en su totalidad.

• Debido a las condiciones ambientales de exteriores como fuertes ráfagas de viento, nieve intensa, granizo, lluvia,

etc. La caja ecológica, junto con su soporte, tubo de extensión y tornillería, se deben inspeccionar cuando menos

una vez al año e inmediatamente después de cualquier ocasión en que los vientos excedan de 90 mph. Un instalador

o inspector caliﬁcado deberá revisar que no haya signos de corrosión, ﬁjadores sueltos, metal doblado, etc. Si hay

señales de desgaste excesivo, deterioro o cualquier condición insegura, inmediatamente deberá de retirar de servicio

este producto. Si tiene alguna pregunta, diríjase al servicio a clientes.

• Asegúrese de que la superﬁcie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los ﬁ-

jadores y componentes.

• Nunca sobrepase la capacidad máxima de soportar carga. Vea la página 8.

• Si va a instalar el producto en una pared con montantes de madera, asegúrese de que los tornillos de montaje estén

anclados en el centro de los montantes. Se recomienda utilizar un localizador de montantes de "borde a borde".

• Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo

con más seguridad.

• Apriete los tornillos con ﬁrmeza, pero no en exceso. Apretarlos en exceso puede dañar los artículos y puede disminu-

ir signiﬁcativamente su fuerza de ﬁjación.

• Este producto fue diseñado para su uso con otros productos al aire libre.

ADVERTENCIA

Herramientas necesarias para el ensamblaje

•llave Allen de 6 mm y 3/16"

•taladro

•broca de 3/8" (10 mm) para paredes de concreto

•nivel

10 de 24 PUBLICADO: 08-09-10 HOJA #: 061-9058-4 10-18-10

Español

ABC

Las piezas pueden verse un poco distintas a la ilustración.

Antes de comenzar, asegúrese de que su producto contiene todas las piezas que se muestran.

Descripción Cant. Nº de pieza N° de Modelo Nº de pieza

Acaja adaptadora 1061-7350 FPECMC-01 061-7368

Bplaca inclinable 1061-7351 FPECMC-02 061-7369

Cplaca de techo 1061-7353 FPECMC-03 061-7370

Dcolumna de apoyo 1véase el gráfico FPECMC-04 061-7371

Etornillos de cabeza hueca de M10 x 16 mm 4 520-5013

Farandelas de cierre partidas 4540-5001

Gtornillos de cabeza hueca de 1/4-20 x .75" 6 520-5034

Htuerca nylock de 1/4"-20 6530-5007

Ipernos en U 2 520-5037

Jperno de cabeza plana 3 520-5039

Ktuerca nylock de 3/8" 3 530-5004

Lanclajes de expansión para concreto 6 5M9-381-H03

Marandelas de 5mm 6 540-5014

Lista de piezas Columna de Apoyo (D)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere PEERLESS Mounts Rack & Stand Handbücher

PEERLESS Mounts

PEERLESS Mounts Paramount PF660 Leitfaden

PEERLESS Mounts

PEERLESS Mounts ACC328 Leitfaden

PEERLESS Mounts

PEERLESS Mounts SmartMount ST630P Leitfaden

PEERLESS Mounts

PEERLESS Mounts LCT-A1B6C Leitfaden

PEERLESS Mounts

PEERLESS Mounts PLAV70-UNLP-GB Leitfaden

PEERLESS Mounts

PEERLESS Mounts RTLA-100 Leitfaden

PEERLESS Mounts

PEERLESS Mounts SUT660P Leitfaden

PEERLESS Mounts

PEERLESS Mounts LCT-A1B4C Leitfaden

PEERLESS Mounts

PEERLESS Mounts ACC488 Leitfaden

PEERLESS Mounts

PEERLESS Mounts LCT-A1B2H Leitfaden

PEERLESS Mounts

PEERLESS Mounts DS-VL-H048 Leitfaden

PEERLESS Mounts

PEERLESS Mounts DS-VL-H072 Leitfaden

PEERLESS Mounts

PEERLESS Mounts SmartMount SA740P Leitfaden

PEERLESS Mounts

PEERLESS Mounts FPEWM Leitfaden

PEERLESS Mounts

PEERLESS Mounts SmartMount SF630P Leitfaden

PEERLESS Mounts

PEERLESS Mounts SmartMount ST632P Leitfaden

PEERLESS Mounts

PEERLESS Mounts LCT-A1B1C Leitfaden

PEERLESS Mounts

PEERLESS Mounts Vector Pro II PJF2-UNV Series Leitfaden

PEERLESS Mounts

PEERLESS Mounts PLA 50-UNL Leitfaden

PEERLESS Mounts

PEERLESS Mounts PRG UNV Leitfaden

PEERLESS Mounts

PEERLESS Mounts Solid-Point PLA 2 Leitfaden

PEERLESS Mounts

PEERLESS Mounts DS-VL-H060 Leitfaden

PEERLESS Mounts

PEERLESS Mounts ACC 310 Leitfaden

PEERLESS Mounts

PEERLESS Mounts SmartMount ST635 Leitfaden

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung