PEERLESS JMWS 30 Leitfaden
ISSUED: 7-8-98 SHEET #: 128-9017-4 08-19-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
1 of 5
AB
C
C
D
E
E
G
H
J
K
F
BLACK SILVER
PART # PART# QTY. DESCRIPTION
A095-1021 095-4021 1 support tray (model JMWS 30)
095-1022 095-4022 1 support tray (model JMWS 35)
B046-1002 046-4002 1 back clamp
C128-1092 128-4092 2 wall arm
D124-1533 124-4533 1 cross plate
E590-1021 590-4014 2 end cap
F046-1001 046-4001 1 base ring
G505-9010 500-2001 6 M5 x .8 x 10 mm penta-pin screw
H5S1-015-C03 5S1-015-C04 6 #14 x 2.5" (6 mm x 65 mm) screw
I510-9110 510-9164 6 1/4-20 x 1" phillips screw
J590-1037 590-2037 12 glide
K590-1036 590-2036 12 spacer
L520-1048 520-2048 4 M6 x 1 x 20 mm phillips screw
M520-9249 520-9249 1 penta-pin driver
N2245-081 2245-081S 4 uni-clip
O520-9258 520-9281 4 #10 x 3/4" penta-pin screw
P540-9400 540-9442 4 flat washer
L
IMPORTANT! Read entire instruction sheet before
you start installation and assembly.
Before you start make sure all parts shown below
are included with your product.
Installation and Assembly - Jumbo Shelf Models: JMWS 30, JMWS 30S,
JMWS 35, JMWS 35S
Parts List
Note: Some parts may appear slightly different than illustrated.
O
M
N
P
I
AvailableAccessories:
●Concrete Anchor Kit
model ACC 203 (two
required)
●VCR Mount models
VPM40-N,VPM40-NS,
SVPM40-N,SVPM40-NS
●Safety Belt model
ACC 666
JMWS 30, JMWS 30S
JMWS 35, JMWS 35S
R
This product is intended for use with UL Listed
products and must be installed by a qualified
professional installer.
Product is UL rated up to 36" TV, 250 lbs.
Product is UL rated up to 32" TV, 250 lbs.
ISSUED: 7-8-98 SHEET #: 128-9017-4 08-19-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
2 of 5
For Wood Stud Walls locate and mark two
stud centers. Studs must measure 16" (406
mm) from center to center. Drill one top left
mounting hole [5/32"(4 mm) dia.] to a minimum
depth of 2.5" (64 mm). Attach left side of double
wall arm using one #14 x 2.5" (6 mm x 65 mm)
woodscrew(H).
Whileholdingdoublewallarmlevel(usealevel),
drill one top right mounting hole [5/32" (4 mm)
dia.] to a minimum depth of 2.5" (64 mm).
Attach right side of double wall arm using one
#14 x 2.5" (6 mm x 65 mm) wood screw (H).
Drillfourremainingholesandattachusingfour
#14 x 2.5" (6 mm x 65 mm) wood screws (H).
C
C
E
ED
Snap end caps (E) into ends of wall arms (C).
Attach cross plate (D) to wall arms (C) using
screws (L). Leave screws (L) slightly loose
until all four are placed, then tighten com-
pletely.
!
"
L
H
16"
(406 mm)
• Tighten wood screws so that double wall arm is firmly
attached,but donot overtighten.Overtightening can
damagethe screws, greatlyreducing theirholding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finderis highlyrecommended.
WARNING
ISSUED: 7-8-98 SHEET #: 128-9017-4 08-19-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
3 of 5
#For Concrete Wall use jumbo shelf, making
sure that it is level, as a template to mark
holes. Drill 1/4" (6 mm) dia. holes to a
minimumdepth of2.5" (64mm).Concrete
must be 2000 psi density minimum. Insert
anchors in holes flush with wall as shown
(right).Placejumboshelfoveranchorsand
secure with #14 x 2.5" (6 mm x 65 mm) wood
screws.Tightenallfasteners.
1
3
concrete
wall
concrete
anchor
concrete
anchor
concrete
anchor
D
D
2A
Tighten to 80 in • lb (9 N.M.) torque.
CUTAWAYVIEW
INCORRECT
concrete
plaster/
drywall
mounting
plate
CORRECT
concrete
plaster/
drywall
mounting
plate
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill
toavoid breaking outthe back ofthe hole whenentering a voidor cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hard-
wareand components.
ACC 203 (sold
seperateley)
• Tightenwood screws firmly,but donot overtighten.
Overtighteningcan damagethe screws,greatly
reducingtheir holdingpower.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
• Concrete anchors are not intendedfor attachmentto
concretewall covered witha layer ofplaster,drywall,
orother finishing material.If mounting toconcrete wall
coveredwith plaster/drywallis unavoidable,plaster/
drywall (up to 5/8" thick) must be counterbored as
shown below. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
WARNING
16"
(406 mm)
ISSUED: 7-8-98 SHEET #: 128-9017-4 08-19-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
4 of 5
Snaptwelve glides
(J)around edgeof
base ring (F) as
shown.
JF
$
K
I
Securelytighten four screws
(L).Attach base ring (F) to
cross plate (D) using six
screws ( I ) and twelve
spacers (K).Note: Cutouts in
base ring (F) must be posi-
tioned towards the back.
%
CUTOUTS
F
D
L
ISSUED: 7-8-98 SHEET #: 128-9017-4 08-19-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
5 of 5
OM
N
P
G
Using uni-clips (N) and M5 screws (G) (see instruction card in
fastenerpack), orparticle boardscrews(O)andwashers (P)
(forattachmentto mounting bossesif present), or acombina-
tion of both, attach support tray (A) to TV bottom. Attach at
four places as close to the four corners of the TV bottom as
possible.Usepenta-pintool(M) anda1/4" drivertodrive
screws.
&
G
'
C
F
B
©2004PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
Attach TV/support tray (A) to base ring
(F) using back clamp (B) and two M5 x
.8 x 10 mm penta-pin self tapping
screws (G). Use penta-pin tool (M) and a
1/4"driver todrive screws.
• Always use an assistant or mechanical lifting equip-
ment to safely lift and position theTV or monitor.
WARNING
Dieses Handbuch passt für folgende Modelle
3
Andere PEERLESS Rack & Stand Handbücher
PEERLESS
PEERLESS LCC 18-C Leitfaden
PEERLESS
PEERLESS PLA 60-UNL Leitfaden
PEERLESS
PEERLESS Vision Point LCFS 100 Leitfaden
PEERLESS
PEERLESS IMC 18 Leitfaden
PEERLESS
PEERLESS VPM 25-W Leitfaden
PEERLESS
PEERLESS Paramount PC930A Leitfaden
PEERLESS
PEERLESS PM 47 Leitfaden
PEERLESS
PEERLESS SA761P Leitfaden
PEERLESS
PEERLESS Solid-Point PS 1 Leitfaden
PEERLESS
PEERLESS DS-VW660 and assembly Leitfaden
PEERLESS
PEERLESS SP730P Leitfaden
PEERLESS
PEERLESS SR1G Leitfaden
PEERLESS
PEERLESS PTT188743 Series Bedienungsanleitung
PEERLESS
PEERLESS PARAMOUNT PRA2X2 Bedienungsanleitung
PEERLESS
PEERLESS Slimline OP-LWB 530 Leitfaden
PEERLESS
PEERLESS SmartMount SP850-UNL Leitfaden
PEERLESS
PEERLESS Paramount PA760 Leitfaden
PEERLESS
PEERLESS LCC 18 Leitfaden
PEERLESS
PEERLESS Smartmount D-FPF-220 Leitfaden
PEERLESS
PEERLESS Smartmount SA752PU Leitfaden
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
