PEERLESS SAL730P Leitfaden

Max ULLoad Capacity: 25 lb (11.3 kg)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 06-10-05 SHEET #: 095-9223-8 09-07-06

Installation and Assembly:

LCD Screen Adjustable Wall/Cabinet Mount

Models: SAL730P, SAL730P-S, RTLAL-100, RTLAL-100S, D-LAL-100,

D-LAL-100S, 105457

Features:

• Fits 10" - 22" LCD screens

• Pivotsand articulatesin alldirections, evenaround cornersand cabinets

• Frees up space by folding flat against the wall

• Keeps electronic wires routed internally to reduce clutter

2 of 30 ISSUED: 06-10-05 SHEET #: 095-9223-8 09-07-06

Forcustomer care call(800) 729-0307 or(708) 865-8870.

Table of Contents

Parts List.............................................................................................................................................................................. 3

InstallationtoSideof Cabinet ........................................................................................................................................... 4, 5

Installation to Wood Stud Wall ............................................................................................................................................. 6

Installation to Solid Concrete and Cinder Block .................................................................................................................... 7

Tools Needed for Assembly

• studfinder ("edgeto edge"stud finder is recommended)

• phillipsscrewdriver

• drill with 1/4" and 5/32" drill bits

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call

Peerless customer service at 1-800-729-0307.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never mount this product to a metal stud wall construction unless the stud can be verified to be constructed of 25

gauge steel minimum, the drywall is 1/2" thick minimum and you obtain and use the Peerless accessory kit for metal

studs.

• Neverexceed the MaximumULLoadCapacity.

• If mounting to wood wall stud wall construction, make sure that mounting screws are anchored into the center of the

studs. Use of an "edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power. See suggested torque values where applicable within these instructions.

WARNING

Accessories

• Metal StudAccessory Kit (ACC 908) (Not evaluated by UL)

Notes:

• Read entire instruction sheet before you start installation and assembly.

• Screen must be attached to the mount to enable tilting.

3 of 30 ISSUED: 06-10-05 SHEET #: 095-9223-8 09-07-06

D-LAL-100 D-LAL-100S

RTLAL-100 RTLAL-100S

SAL730P SAL730P-S

105457

Description Qty. Part # Part #

Awall arm assembly 1 095-0386-B 095-0386-S

B1/4-20 x 1.5" flat head screw 2 520-1264 520-2164

C.25" ID x .75" OD x 1/16" H washer 2 540-2015 540-2015

D1/4-20 nylock nut 2 530-2002 530-2002

E3/16" allen wrench 1 560-0071 560-0071

FAlligator® concrete anchor 2 590-0097 590-0097

G#14 x 2.5" flat head wood screw 2 520-1202 520-2165

HM4 x .7 x 12 mm phillips screw 4 504-9013 504-2013

Icord management clip 2 590-1264 590-2164

J.198" ID x .313" OD x .437" H retaining spacer 4 590-5005 590-5003

KM4 x .7 x 20 mm phillips screw 4 504-9020 504-2014

L5 mm allen wrench 1 560-9640 560-9640

Parts List

IJK

4 of 30 ISSUED: 06-10-05 SHEET #: 095-9223-8 09-07-06

fig. 1.2

fig. 1.1

SCREEN

CABINET

DOOR

CABINET

DOOR WALL

WALL

“D1” 11-7/8"

(302 mm)

max. distance from

cabinet door is

Installation to Side of Cabinet

If you are mounting your screen to a wall, skip to page 6 for wood stud walls and page 7 for concrete walls.

Note: Screen is not attached to mount at this point. It is shown only as a reference for visualization purposes.

Place your screen on side wall of cabinet in a location that will allow enough clearance between the screen and the

back wall when the mount is folded up as shown in figure 1.1. Mark the center of screen on the cabinet. Mark a

vertical line 1-1/2” (38 mm) toward the wall which represents the center of wall plate. Dimension “D1” represents the

minimum distance between the wall plate and the screen for this clearance.

Go to next page for installing the mount to the cabinet.

To swivel screen around the cabinet, read below.

If you would like the screen to swivel around the cabinet, place your wall arm in a location that will allow enough

clearance between the wall arm and the cabinet door as shown in figure 1.2.The dimension 11-7/8" (302 mm)

represents the maximum distance the center of the wall plate needs to be from the cabinet door. Mark a vertical line

on the cabinet where the wall arm assembly will be placed as shown in figure 1.2.

Notes:

• Beforeswiveling thewall armaround cabinet, ensure the cords have enough slack to allow fullarticulation ofwall

arm(A).

• Toallow swiveling around the cabinet and folding up the mount, the minimum distance from cabinet door must be

at least equal to dimension “D1”.

Go to next page for installing the mount to the cabinet.

Side View of Cabinet

(wall arm folded up against cabinet) Side View of Cabinet

(wall arm swiveled around cabinet)

• Make sure that the cabinet unit and cabinet side wall

will safely support the combined load of the

equipmentand all attached hardwareand

components.

• Beforeinstalling yourmount, emptycabinet and note

locationof shelves to avoiddrilling into theshelves.

CAUTIONWARNING

CS = center of screen

CP = center of wall plate

CS CP

1-1/2"

(38 mm)

WALL PLATE

5 of 30 ISSUED: 06-10-05 SHEET #: 095-9223-8 09-07-06

CORDCOVERS

Remove cord covers from wall arm assembly (A) as shown in figure 1.3. Use wall plate as template to mark center of

holes along the vertical line drawn in step 1. Make sure wall plate is level, then drill two 9/32" (7 mm) holes through

cabinetwallwhere marked.

Installation to Side of Cabinet

WALL

VERTICALLINE

WALL PLATE

Fasten wall arm assembly (A) to side of cabinet using two 1/4-20 flat head screws (B), washers (C), and 1/4-20

nylock nuts (D) as shown in figures 1.4 and 1.5.

Skip to step 2 on page 8.

CABINETSIDE WALL

A B CD

Bfig. 1.5

CABINET

SIDE

WALL

Side View of Cabinet

Cutaway View of Cabinet Side Wall

Isometric View of

Cabinet Side Wall

1-2

1-1

fig. 1.3

fig. 1.4

6 of 30 ISSUED: 06-10-05 SHEET #: 095-9223-8 09-07-06

Installation to Wood Stud Wall

Remove cord covers from wall arm (A) as shown in figure 1.6. Using a stud finder, locate and mark the edges of the

wood stud used in mounting this product. Use of an edge to edge stud finder is highly recommended. Use a level to

draw a vertical line down the center of the stud. Use wall plate as template to mark center of holes along the vertical

line. Drill two 5/32" (4 mm) dia. holes 2.5" (65 mm) deep.Attach wall arm (A) to wall using two #14 x 2.5" flat head

wood screws (G) as shown in figure 1.7.

Skip to step 2 on page 8.

• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhardwareand

components.

WARNING

WOOD

STUD

WALL

fig. 1.7

fig. 1.6

CORDCOVERS

• Tightenscrews sothat wallplate is firmly attached, but do not overtighten. Overtightening can damagethe screws,

greatlyreducingtheirholdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is

highlyrecommended.

WARNING

7 of 30 ISSUED: 06-10-05 SHEET #: 095-9223-8 09-07-06

Installation to Solid Concrete and Cinder Block

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.

It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid

breakingout the backof the hole when enteringa void orcavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardwareandcomponents.

WARNING

Removecord covers from wall arm(A) as shownin

figure 1.6. Level and use wall arm as template to

mark center of holes. Drill two 1/4" (6 mm) dia. holes

to a minimum depth of 2" (51 mm). Insert anchors (F)

in holes flush with wall as shown in fig 1.8. Place wall

arm(A) over anchorand secure with wood screw(G)

as shown in figures 1.9 and 1.11. Make sure wall arm

is level, and tighten all fasteners. See figure 1.10.

• Concrete anchors are notintendedfor attachment to

concretewall covered witha layer ofplaster,drywall,

orother finishing material asshown below. If mounting

toconcrete wall coveredwith plaster/drywall is

unavoidable,plaster/drywall (up to5/8" thick) mustbe

counterboredas shown below. Besureconcrete

anchorsdo not pullaway from concretewhen tighten-

ing screws. If plaster/drywall is thicker than

5/8", custom fasteners must be supplied by installer.

WARNING

concrete

wall

Drill holes

and insert

anchors.

Place wall

plate over

anchor and

secure with

screw.

Tighten all

fasteners.

WALL ARM

fig. 1.8

fig. 1.9

fig. 1.10

CUTAWAYVIEW

CORRECT

concrete

plaster/

drywall

INCORRECT

concrete

plaster/

drywall

• Tighten screws so that wall plate is firmly attached,

butdonotovertighten. Overtightening can damage the

screws,greatlyreducing their holdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

AGF

fig. 1.11

8 of 30 ISSUED: 06-10-05 SHEET #: 095-9223-8 09-07-06

Insert two M4 x 12 mm screws (H) into top two holes

ofscreen, leaving approximately 1/4" ofexposed

thread. Hook screws onto keyslots of adapter plate

as indicated in figures 2.1 and 2.2.

*Note: If hole pattern is in a pocket, insert two M4 x

20 mm screws (K) with two retaining spacers (J) into

top two holes of screen as indicated right.

fig. 2.1

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

Note: Toadd security, orderACC 918 for security

screws.Refer toACC918 instruction sheetfor

installing security screws.

1/4"

*For screens with a

hole pattern in a

pocket, spacers (J)

go between adapter

plate and screen.

ADAPTER

PLATE

FOR VESA®75

MOUNTINGPATTERN: FOR VESA100

MOUNTINGPATTERN:

fig. 2.2

Screen may appear

slightlydifferentthan

illustrated

InsertoneM4screw(H)throughbottomholeof

adapterplateas shown infigure3.1.

fig. 3.1

ADAPTER

PLATE

9 of 30 ISSUED: 06-10-05 SHEET #: 095-9223-8 09-07-06

Route cords through center of cord management clip (I). Next, attach cord management clip to adapter plate using

M4 screw (H) as shown in detail 1. Tighten all four screws (H).

Note:Acord management clip (I) was added for additional cords. If you want to use this added clip, remove the

opposite bottom screw and repeat this step on opposite side of adapter plate.

Idetail 1

Note: Makesure cords haveenough slack to allow fullmovement of thearm.

Route cords inside arm slots of wall arm assembly (A). Optional: Run power cord through one side of mount and

signalcable(s) through othersideto avoid interferencewith the signal.

Lock cords into place by sliding cord covers onto mount. Screen may have to be moved for better access for sliding

onthe cord covers.

CORDCOVERS

10 of 30 ISSUED: 06-10-05 SHEET #: 095-9223-8 09-07-06

If more or less tension is desired in the arm pivot points, do the following:

• To increase tension, turn socket screw clockwise with 3/16" allen wrench (E).

• To reduce tension, turn socket screw counter-clockwise with allen wrench (E). Do not turn more than half a turn.

PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

SOCKETSCREWS

NOTE: Adjustmentpoints(socket screws) are factory torquedfor optimal performance. This factory torque setting is

recommended to prevent the screen from slipping over time. If moreor less tensionis desired followthis optional

step. You may not achieve optimal torque value if factory torque settings are adjusted.

If more or less tension is desired in tilt mechanism, remove snap caps as shown in detail 2. Insert a flat head screw

driver into slot and pry cap away from tilt mechanism. To adjust tilt, simply tighten or loosen socket screw no more

than half a turn using 5 mm allen wrench (L). To adjust roll, simply tighten or loosen 10-32 nylock nut.

SNAPCAP

SOCKET

SCREW

10-32NYLOCKNUT

detail 2

OPTIONAL

SLOT

• Donot remove screw orloosenscrewuntilitisnolongerengaged with the mount.Doingsomaycausethescreentofall.

WARNING

Andere Handbücher für SAL730P

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere PEERLESS Rack & Stand Handbücher

PEERLESS

PEERLESS SOLID-POINT PLCM1CP Bedienungsanleitung

PEERLESS

PEERLESS SR1G Leitfaden

PEERLESS

PEERLESS PM 47 Leitfaden

PEERLESS

PEERLESS ESA746PU Leitfaden

PEERLESS

PEERLESS PLT BLK Leitfaden

PEERLESS

PEERLESS Paramount PP730 and assembly Leitfaden

PEERLESS

PEERLESS SUF650P and assembly Leitfaden

PEERLESS

PEERLESS Vision-Point LCV 100 Leitfaden

PEERLESS

PEERLESS DS-VW650 Leitfaden

PEERLESS

PEERLESS SmartMount SP740P Leitfaden

PEERLESS

PEERLESS Smartmount SA752PU Leitfaden

PEERLESS

PEERLESS WSP700 Bedienungsanleitung

PEERLESS

PEERLESS WSP700 Bedienungsanleitung

PEERLESS

PEERLESS A100IWBMOUNT Leitfaden

PEERLESS

PEERLESS RTLA-100 Leitfaden

PEERLESS

PEERLESS Paramount PC930A Leitfaden

PEERLESS

PEERLESS SF630P-S and assembly Leitfaden

PEERLESS

PEERLESS VPM 25-W Leitfaden

PEERLESS

PEERLESS SGLS01 Leitfaden

PEERLESS

PEERLESS SOLID POINT PLCM 1 Bedienungsanleitung

PEERLESS

PEERLESS LMAM1940 Leitfaden

PEERLESS

PEERLESS SF 24D Leitfaden

PEERLESS

PEERLESS PANA-85WM Leitfaden

PEERLESS

PEERLESS MOD-FPSKIT150 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung