PEERLESS Designer Series Leitfaden
ISSUED: 06-02-00 SHEET #: 170-9014-4 08-13-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
1 of 5
PART # PART # PART #
(Black) (White) (Silver) QTY. DESCRIPTION
A170-1033 170-2033 170-4033 1 31" support tray
B170-1034 170-2034 170-4034 1 27" cross arm
C170-1035 170-2035 170-4035 1 22" wall support arm
D170-1036 170-2036 170-4036 2 tilt adjuster gusset
E170-1039 170-2039 170-4039 1 11" wall bracket
F590-1005 9PT-66SW02P 590-4005 2 bushing
G590-1007 6PT-66XX02P 590-4118 1 retainer plug
H560-9643 560-9643 560-9643 1 retainer pin
I590-1053 590-1054 590-4053 2 cross arm endcap
J1545-275 1545-285 1545-265 1 retainer strap
K520-9400 5S2-M08-H71 5S2-M08-H71 1 M8 x 70 mm bolt
L520-9250 520-2005 520-2005 4 M5 x .8 x 10 mm pan screw
M1545-274 9PT-99XX02P 9PT-99XX02P 1 draw bar
N520-9270 520-9278 520-9278 2 M6 x 16 mm screw bolt
O520-1023 520-9406 520-9406 2 M5 x .8 x 6 mm pan screw
P560-9640 560-9640 560-9640 1 5 mm allen wrench
Q5S1-015-C03 5S1-015-C04 5S1-015-C04 3 #14 x 2.5 hex screw
Installation and Assembly - Designer Series TV Wall
Mount for 32" TV's Model: DS 32, DS 32-SV,
DS 32W
IMPORTANT! Read entire instruction sheet before you start installation and assembly.
Parts List
B
A
E
I
F
H
G
J
D
Q
Before you start make sure all parts listed are included with your product.
Fasteners
N
L
O
C
K
M
M A X I M U M L O A D C A P A C I T Y
MODELNUMBER MAX WEIGHT OF TV
DS 32, DS 32-SV, DS 32W 160 lbs. (73 kg.)
R
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
P
ISSUED: 06-02-00 SHEET #: 170-9014-4 08-13-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
2 of 5
For Wood Stud Walls (for concrete skip to step 2) drill
three 5/32" (4 mm) dia. holes 2 1/2" (65 mm) deep.
Attach wall bracket (E) using #14 x 2.5 (6 mm x 65 mm)
wood screws (Q).
Æ 5/32" (4 mm)
3/8"
(10 mm)
E
Q
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1 3/8" of actual concrete
surface in the 1/4" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of
ahammerdrilltoavoidbreakingoutthebackoftheholewhenenteringavoidorcavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support 4 times the combined load of the equipment and all attached hardware
andcomponents.
• NeverexceedtheMaximumLoadCapacityof160lb(73kg).
WARNING
• Tighten wood screws so that wall plate is firmly
attached,butdonotovertighten.Overtighteningcan
damagethescrews,greatlyreducingtheirholding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finderishighlyrecommended.
WARNING
ISSUED: 06-02-00 SHEET #: 170-9014-4 08-13-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
3 of 5
For Concrete Walls use wall bracket, making sure that it is
level, as a template to mark holes. Drill 1/4" (6 mm) dia. holes
to a minimum depth of 2.5" (64 mm). Concrete must be 2000
psi density minimum. Insert anchors in holes flush with wall
as shown (right). Place wall bracket over anchors and secure
with #14 x 2.5" (6 mm x 65 mm) wood screws. Tighten all
fasteners.
CUTAWAY VIEW
• Tighten wood screws so that wall plate is firmly
attached,butdonot overtighten.Overtighteningcan
damagethescrews,greatlyreducingtheirholding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finderishighlyrecommended.
WARNING
concrete
1
3
2
ACC203
(soldseparately)
Drillhole(s)andinsertanchor(s).
Placewallbracketoveranchor(s)andsecurewith
screw(s).
Tightenallfasteners.
wall
bracket
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Neverattachconcreteexpansionanchorstoconcrete
coveredwithplaster, drywall,orotherfinishingmate-
rial.Ifmountingtoconcretesurfacescoveredwitha
finishingsurfaceisunavoidable,the finishing surface
mustbecounterboredasshowninFigure1.Iffinishing
surface is thicker than 5/8", custom fasteners must be
suppliedbyinstaller.
WARNING
INCORRECT E
∅ 5/16" (8 mm)
ACC203 (not included)
E
∅ 5/16" (8 mm)
ACC203 (not included)
CORRECT
Figure 1
plaster/
drywall
mounting plate concrete
concrete
plaster/
drywall
mounting plate
ACC203
(soldseparately)
ISSUED: 06-02-00 SHEET #: 170-9014-4 08-13-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
4 of 5
Join support arm
(C) and plug
retainer (G) with
retainer pin (H).
Note: A gentle tap
with a hammer
may be necessary
to insert retainer
pin (H).
Snap bushings
(F) into wall
bracket(E).
Slide retainer
strap (J) onto
support arm (C)
Insert support
arm (C) into wall
bracket (E), then
insert support
arm retainer (G).
F
F
E
G
H
EE
CCC
GG
Plug retainer (G)
will hold support
arm (C) in place
on wall bracket (E).
Insert endcaps (I) into cross arm (B). Slide draw bar (M) into
support arm (C). Attach cross arm (B) to support arm (C) with
screw bolt (K) into draw bar (M) using allen wrench (P).
Note: Two holes in crossarm (B) (for VCR attachment)
should face bottom.
J
C
C
M
B
I
I
K
P
ISSUED: 06-02-00 SHEET #: 170-9014-4 08-13-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
5 of 5
Attach two tilt adjuster gussets (D) to
retainer strap (J) using two screws (O).
There are three settings (0°, 5° & 10° tilt).
Attach tray (A) to gussets (D) using four screws (L).
Secure tray (A) to endcaps (I) using two screws (N).
D
D
J
L
L
L
N
D
D
I
I
L
O
N
0°5°
10°
O
A
©2004PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
• Tray must be attached using the two holes at the front
of the tray as indicated. Moving it forward by attaching
toholesprovidedforTVmountingmaycausean
unsafemountingcondition.
WARNING
Dieses Handbuch passt für folgende Modelle
3
Andere PEERLESS TV-Halterung Handbücher
PEERLESS
PEERLESS PARAMOUNT PA730 Leitfaden
PEERLESS
PEERLESS PARAMOUNT PRFLU Bedienungsanleitung
PEERLESS
PEERLESS PARAMOUNT PA740 Leitfaden
PEERLESS
PEERLESS Jumbo 2000 JM 2630 Leitfaden
PEERLESS
PEERLESS PARAMOUNT PT660 Bedienungsanleitung
PEERLESS
PEERLESS EWMU Leitfaden
PEERLESS
PEERLESS PARAMOUNT PT632 and assembly Leitfaden
PEERLESS
PEERLESS SlimLine SLWS210/BK Bedienungsanleitung
PEERLESS
PEERLESS IM740P Leitfaden
PEERLESS
PEERLESS HAVE1 FPZ-655 Bedienungsanleitung
PEERLESS
PEERLESS D-FPT2-320 Leitfaden
PEERLESS
PEERLESS SUT645P Leitfaden
PEERLESS
PEERLESS Smartmount ST632P Leitfaden
PEERLESS
PEERLESS ECMU-01-C-S Leitfaden
PEERLESS
PEERLESS PLP PION50 Leitfaden
PEERLESS
PEERLESS SMARTMOUNT SF 635P Leitfaden
PEERLESS
PEERLESS SUF650P and assembly Leitfaden
PEERLESS
PEERLESS ST 632P Leitfaden
PEERLESS
PEERLESS PARAMOUNT PF632 and assembly Leitfaden
PEERLESS
PEERLESS DS-VL-H024 Leitfaden
