PEERLESS PARAMOUNT PP740 Leitfaden

Features:

•Fits 22" - 40" (56 - 102 cm) LCD screens

• Two tensionable pivot points for extensive adjustment of

viewing angle

• VESA®75/100/200 x 100/200 x 200 compatible

• Frees up space by folding ﬂat against the wall

Installation and Assembly:

Paramount™ Pivot for 22" - 40" (56 - 102 cm) LCD screens

Models: PP740, PWV240/BK

Max Load Capacity: 80lb (36 kg)

USC

ISSUED: 02-05-09 SHEET #: 202-9312-1

2 of 20 ISSUED: 02-05-09 SHEET #: 202-9312-1

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

• Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit - WSP490;

• Brick Contact Qualiﬁed Professional

• Other or unsure? Contact Qualiﬁed Professional

WARNING

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Wood Stud Wall................................................................................................................................................4

Installation to Solid Concrete and Cinder Block .....................................................................................................................5

Attaching Adapter Plate to Screen with VESA®Mounting Pattern..........................................................................................6

Installing to Peerless LC or PLP Model Adapter Bracket .......................................................................................................8

Cord Management and Arm Tension Adjustment ................................................................................................................10

NOTE: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

•stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

•drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

• level

3 of 20 ISSUED: 02-05-09 SHEET #: 202-9312-1

GIJ

MNO

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

PWV240/B

PP740

Description Qt

.Part #

wall mount assembly 1095-0545-GB

Bconcrete anchor 2 590-0320

Cretaining spacer 4 590-5005

D1/4-20 x 13 mm flat head phillips screw 2 520-1209

EM4 x 10 mm phillips screw 4 504-9012

FM4 x 20 mm phillips screw 4 504-9020

GM6 x 12 mm phillips screw 4 520-1128

H#14 x 63.5 mm flat head wood screw 2 520-1202

IM6 x 20 mm phillips screw 4 520-9402

JM6 x 30 mm phillips screw 4 510-9109

KM5 x 6 mm phillips screw 5 520-1023

L#10 flat washer 4 540-9400

Mhook bracket 1 095-P1346

Nadapter plate 1095-P1322

O#10-32 x 6 mm flat head phillips screw 1 520-1108

Pcable tie 1 560-1725

Parts List

4 of 20 ISSUED: 02-05-09 SHEET #: 202-9312-1

Installation to Wood Stud Wall

Using a stud ﬁnder, locate and mark the edges of the wood stud used in mounting this product. Use of an edge to

edge stud ﬁnder is highly recommended. Use a level to draw a vertical line down the center of the stud. Use wall

plate as template to mark center of holes along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (64 mm)

deep. Attach wall mount (A) to wall using two #14 x 63.5 mm ﬂat head wood screws (H) as shown.

Skip to step 2 on page 6.

WOOD STUD WALL

WALL PLATE

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations (not UL approved).

WARNING

5 of 20 ISSUED: 02-05-09 SHEET #: 202-9312-1

Installation to Solid Concrete and Cinder Block

Level and use wall plate as template to mark center

of holes. Drill two 5/16" (8 mm) dia. holes to a

minimum depth of 2.5" (64 mm). Insert anchors (B)

in holes ﬂush with wall. Place wall mount (A) over

anchors and secure with wood screws (H). Make

sure wall mount is level, and tighten all fasteners.

WALL PLATE

SOLID CONCRETE CINDER BLOCK

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall plaster/

drywall

concrete concrete

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a

solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90

speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

the screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material. If mounting to concrete surfaces

covered with a ﬁnishing surface is unavoidable,

the ﬁnishing surface must be counterbored as

shown below. Be sure concrete anchors do not

pull away from concrete when tightening screws. If

plaster/drywall is thicker than 5/8" (16 mm), custom

fasteners must be supplied by installer.

WARNING

Drill holes and insert anchors (B).

Place plate (A) over anchors (B) and secure with screws (H).

Tighten all fasteners.

concrete

surface

6 of 20 ISSUED: 02-05-09 SHEET #: 202-9312-1

Attaching Adapter Plate to Screen with VESA®200 x 100

or 200 x 200 Mounting Pattern

Attach hook bracket (M) to adapter plate (N) using

four M5 x 6 mm screws (K) and #10 washers (L) as

shown.

FOR VESA®200 x 100 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach

adapter plate (N) to back of screen using four M4 x

10 mm screws (E) as shown below.

*NOTE: If screw (E) gets less than three threads

of engagement, attach adapter plate (N) to back of

screen using four M4 x 20 mm screws (F) and four

spacers (C) as indicated below.

Skip to step 3 on page 9.

FOR VESA®200 x 200 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach adapter

plate (N) to back of screen using four M6 x 12 mm

screws (G) as shown below.

*NOTE: If screw (G) gets less than three threads

of engagement, attach adapter plate (N) to back of

screen using four M6 x 20 mm screws (I). If screw (I)

still gets less than three threads of engagement, use

four M6 x 30 mm screws (J).

Skip to step 3 on page 9.

NOTE: For VESA 75 mm and 100 mm patterns, see following page.

2-1

• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not

tightly secured, damage may occur to screen or product may fail.

WARNING

*For screens with a

hole pattern in a pocket,

spacers (C) go between

adapter plate (N) and

screen. C

7 of 20 ISSUED: 02-05-09 SHEET #: 202-9312-1

Attaching Hook Bracket to Screen with VESA®75 or 100 Mounting Pattern

FOR VESA®75 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach hook

bracket (M) to back of screen using four M4 x 10

mm screws (E) as shown below.

*NOTE: If hole pattern is in a pocket, attach hook

bracket (M) to back of screen using four M4 x 20

mm screws (F) and four retaining spacers (C) as

indicated below.

FOR VESA®100 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach hook

bracket (M) to back of screen using four M4 x 10

mm screws (E) as shown below.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

*For screens with a

hole pattern in a pocket,

spacers (C) go between

hook bracket (M) and

screen.

8 of 20 ISSUED: 02-05-09 SHEET #: 202-9312-1

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

GENERIC ADAPTER BRACKET

FOR INSTALLING TO PEERLESS LC MODEL ADAPTER BRACKET

For screen compatibility please refer to the LCD or plasma interface list on our website www.peerlessmounts.com or

call customer care for a screen speciﬁc adapter bracket LC or PLP models (not UL evaluated).

FOR INSTALLING TO PEERLESS PLP MODEL ADAPTER BRACKET

GENERIC ADAPTER BRACKET

M5 X 6 MM OR M5 X 10 MM SCREW

M5 X 10 MM SCREW

NOTE: Refer to LC model adapter bracket instruction sheet for attachment of adapter bracket to screen.

NOTE: Either M5 x 6 mm or M5 x 10 mm screws are included with the LC model adapter bracket.

NOTE: Refer to PLP model adapter bracket instruction sheet for attachment of adapter bracket to screen.

NOTE: M5 x 10 mm screws are included with the PLP model adapter bracket.

Attach hook bracket (M) to adapter bracket using four M5 x 6 mm or M5 x 10 mm screws.

Attach hook bracket (M) to adapter bracket using four M5 x 10 mm screws.

9 of 20 ISSUED: 02-05-09 SHEET #: 202-9312-1

Adjust tension knob on side of mount shown in

ﬁg. 4.1 to desired tension to balance your screen

size and weight.

Push or pull from top or bottom of screen to adjust

tilt as shown. The tilt can be adjusted to a maximum

of 15° forward or 5° backward.

• Be careful not to pinch ﬁngers when opening and

closing mount from the wall.

CAUTION

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

TENSION KNOB

ﬁg. 4.1

Roll screen to desired position (5° clockwise or

counter-clockwise). Insert #10-32 x 6 mm ﬂat head

phillips screw (O) to lock screen into position as

shown in ﬁgure 4.2. ﬁg. 4.2

To attach screen to wall mount (A), lower hook

bracket (M) with screen at an angle into pockets of

wall mount as shown in ﬁgure 3.1. Once clips are

engaged, push down to seat clips in pockets as

shown in ﬁgure 3.2. Insert and tighten M5 phillips

screw (K) to lock screen to wall mount as shown in

ﬁgure 3.3.

To remove screen from mount, loosen screw (K)

and lift screen off of mount.

Installing and Removing Flat Panel Screen

SCREEN

ﬁg. 3.1 ﬁg. 3.2

ﬁg. 3.3

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 20 in. • lb (2.26 N.M.) maximum torque.

CAUTION

• Do not lift more weight than you can handle. Use ad-

ditional man power or mechanical lifting equipment

to safely handle placement of the screen.

• Failure to lock hook bracket (M) with screw (K) can

cause screen to come off mount if hit accidentally.

WARNING POCKET

CLIP

4-1

10 of 20 ISSUED: 02-05-09 SHEET #: 202-9312-1

ARM TENSION ADJUSTMENT: If more or less tension is desired in the arm pivot points, do the following:

• To increase tension, turn tension screw(s) clockwise with allen wrench.

• To reduce tension, turn tension screw(s) counter-clockwise with allen wrench.

NOTE: Do not turn more than half a turn.

TENSION

SCREWS

• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the screen

to fall.

WARNING

CORD MANAGEMENT: Tighten cable to top of wall

mount assembly arm (A) using cable tie (P).

Cord Management and Arm Tension Adjustment

CORD

Andere Handbücher für PARAMOUNT PP740

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere PEERLESS TV-Halterung Handbücher

PEERLESS

PEERLESS Smartmount ST650 Leitfaden

PEERLESS

PEERLESS MIS374 Leitfaden

PEERLESS

PEERLESS SF630P and assembly Leitfaden

PEERLESS

PEERLESS Paramount PC930A Bedienungsanleitung

PEERLESS

PEERLESS PARAMOUNT PFT640 and assembly Leitfaden

PEERLESS

PEERLESS Paramount PP730 and assembly Leitfaden

PEERLESS

PEERLESS Smartmount ST640 Bedienungsanleitung

PEERLESS

PEERLESS SLWS410/BK Leitfaden

PEERLESS

PEERLESS SUAC9000 and assembly Leitfaden

PEERLESS

PEERLESS Peerless OneMount Flat Panel Modular Wall Mount... Leitfaden

PEERLESS

PEERLESS ACC324 Leitfaden

PEERLESS

PEERLESS Jumbo 2000 JM 2630 Leitfaden

PEERLESS

PEERLESS Jumbo 2000 OP-JMW2630 Leitfaden

PEERLESS

PEERLESS PARAMOUNT PT630 and assembly Leitfaden

PEERLESS

PEERLESS PARAMOUNT PT640 and assembly Bedienungsanleitung

PEERLESS

PEERLESS HP432-002 Leitfaden

PEERLESS

PEERLESS Smartmount ST630P and assembly Leitfaden

PEERLESS

PEERLESS PARAMOUNT PF630 and assembly Leitfaden

PEERLESS

PEERLESS Smartmount ST632 Bedienungsanleitung

PEERLESS

PEERLESS Smartmount ST630P and assembly Leitfaden

PEERLESS

PEERLESS FLD-UNV Leitfaden

PEERLESS

PEERLESS MM746PU Bedienungsanleitung

PEERLESS

PEERLESS SUF650P and assembly Leitfaden

PEERLESS

PEERLESS HLG452-002 Leitfaden

Beliebte TV-Halterung Handbücher anderer Marken

Ergotron

Ergotron Neo Flex Cantilever UHD Bedienungsanleitung

StarTech.com

StarTech.com FPCEILBTB Bedienungsanleitung

VonHaus

VonHaus 05/038 Bedienungsanleitung

Techlink

Techlink ECHO TV Bedienungsanleitung

Sandstrom

Sandstrom SSTVMC12X Bedienungsanleitung

Sony

Sony SU-WL700 Leitfaden

ICW

ICW SCACC18 Bedienungsanleitung

LG WM-L640V Bedienungsanleitung

Gembird

Gembird WM-65ST-01 Bedienungsanleitung

ERARD

ERARD FiTUP XXL 035320 Bedienungsanleitung

Kanto

Kanto RCF180 Bedienungsanleitung

GEM

GEM GEM GP001 Bedienungsanleitung

Gladiator Joe

Gladiator Joe GJ0A0053 Bedienungsanleitung

Vivotek

Vivotek AM-105 Bedienungsanleitung

Vivo

Vivo VESA STAND-VAD1B Bedienungsanleitung

AmazonBasics

AmazonBasics B07QG3LMG4 Bedienungsanleitung

Secura

Secura QLF210 Bedienungsanleitung

Marquant

Marquant 929-083 Betriebsanleitung