Pentair PROWLER 910 Bedienungsanleitung

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

KREEPY KRAULY®PROWLER®910

INSTALLATION AND

USER’S GUIDE

ROBOTIC ABOVEGROUND POOL CLEANER

KREEPY KRAULY®PROWLER®910 Robotic Aboveground Pool Cleaner Installation and User’s Guide

If you have questions about ordering Pentair Aquatic Systems®replacement parts, and pool products, please use

the following contact information:

CUSTOMER SERVICE / TECHNICAL SUPPORT

Customer Service (8 A.M. to 4:30 P.M. — Eastern

and Paciﬁc Times)

Phone: (800) 831-7133

Fax: (800) 284-4151

Web site

visit www.pentairpool.com or www.staritepool.com to

ﬁnd information about Pentair products.

Technical Support

Sanford, North Carolina (8 A.M. to 4:30 P.M. ET)

Phone: (919) 566-8000

Fax: (919) 566-8920

Moorpark, California (8 A.M. to 4:30 P.M. PT)

Phone: (805) 553-5000 (Ext. 5591)

Fax: (805) 553-5515

TABLE OF CONTENTS

Important Warning and Safety Instructions .......

Initial Setup and Operation ..................................

Overview

Cleaner Components

Initial Setup

Maintenance ........................................................

Removing the Cleaner from the Pool

Cleaning the Filter Basket

Cleaning the Impeller

Storing the Cleaner

Troubleshooting ..................................................

Replacement Parts ..............................................

Illustrated Parts List

Prowler 910 Parts List

P/N 371869 Rev. A 5/13/16

KREEPY KRAULY®PROWLER®910 Robotic Aboveground Pool Cleaner Installation and User’s Guide

Attention Installer: This guide contains important information about the

installation, operation and safe use of this product. This information should

be given to the owner and/or operator of this equipment after installation

of the pool cleaner.

Attention User: This manual contains important information that will help

you in operating and maintaining this pool cleaner. Please retain it for future

reference. Consult Pentair with any questions regarding this equipment.

Important Notice:

Before installing this product, read and follow all

warning notices and instructions which are included.

Failure to follow safety warnings and instructions can result in severe

injury, death, or property damage. Call (800) 831-7133 for additional free

copies of these instructions.

When examining the robotic pool cleaner, disconnect

the main power supply.

Keep the robotic pool cleaner out of reach of

children.

Only an original power cable must be used, at all

times. Replaced by a robotic pool cleaner certiﬁed

technician, in case of need to avoid hazard.

To reduce the risk of electrical shock, do not use

extension cord to connect unit to electrical supply;

provide a properly located outlet.

Consumer Information and Safety

The pool cleaners are designed and manufactured to provide many years

of safe and reliable service when installed, operated and maintained

according to the information in this manual. Throughout the manual, safety

warnings and cautions are identiﬁed by the “ ” symbol. Be sure to read

and comply with all of the warnings and cautions.

HAZARDOUS SUCTION.

Do not play with cleaner or hose or apply to body.

Can trap and tear hair or body parts. Hose can trip or

entangle swimmers which could result in drowning.

RISK OF ELECTRICAL SHOCK OR

ELECTROCUTION.

Connect only to a grounding type receptacle protected

by a ground-fault circuit-interrupter (GFCI). Contact

a qualiﬁed electrician if you cannot verify that the

receptacle is protected by a GFCI.

Only a trained operator should operate the robotic

pool cleaner.

To avoid hand injury, operator should keep hands

away from driving belt mechanism.

Position the caddy and power supply at least 10 feet

(3 m) from the edge of the pool during operation.

Do not bury cord - locate cord to minimize abuse

from lawn mowers, hedge trimmers and other

equipment.

General Installation Information

FCC Statement

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if installed and used in

accordance with the instructions, guarantees that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

interference by one or more following measures:

Pre-Installation Check List

Before installing your cleaner, review and understand all warnings and

safety information in this guide. Failure to follow these instructions or

improper installation of the cleaner can result in damage to the pool

ﬁnish or the vinyl liner, Pentair Aquatic Systems disclaims any liability for

repairs or replacement to any of these structures or components of the

customer’s pool.

Before installing the cleaner in a vinyl liner pool:

Check liner closely for signs of deterioration or damage from age,

chemicals, pool wall damage, etc. If any damage is found, have a qualiﬁed

pool professional make all the necessary repairs. Also, if there are stones,

roots, etc., under the liner, remove them before installing the cleaner.

Before installing the cleaner in a gunite pool or a pool that is partially

or completely tiled:

Repair loose tiles and tighten any loose light rings.

Before installing the cleaner, clean your ﬁlter system:

Make sure you have cleaned the ﬁlter, including backwashing, rinsing,

and emptying all baskets. A clean system is necessary for proper cleaner

operation and coverage.

Before installing the cleaner, understand cleaner coverage:

The cleaner is designed to rid your pool of debris in approximately 4-6

hours. Less time could be needed, depending on the pool size. The

cleaner was not designed to automatically clean steps or swimouts or to

work under a solar cover. It was also not designed to do initial cleanup

for a new pool or when opening your pool for the season.

AFTER installing the cleaner, make sure the cleaner is operating

correctly:

The cleaner may need some minor adjustments to make sure it is

operating properly so there is no damage to the pool ﬁnish. Certain

vinyl liner patterns are particularly susceptible to surface wear, pattern

removal, ink rubbing off of, or serious scratches to the pattern caused by

objects coming into contact with the vinyl surface, including automatic

pool cleaners. Pentair Aquatic Systems is not responsible for any pattern

removal, abrasions or markings on vinyl liners.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations to this equipment not expressly approved by the

party responsible for compliance (Pentair) could void the user’s authority

to operate this equipment.

IMPORTANT WARNING AND SAFETY INSTRUCTIONS

Do not operate the robotic pool cleaner when there

are people swimming in the pool. Hose can trip or

entangle swimmers which could result in drowning.

This product contains a chemical known to the state

of California to cause cancer, birth defects or other

reproductive harm.

Keep the robotic pool cleaner out of reach of

persons with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, without proper

supervision and understanding of the instructions.

When lifting the robotic pool cleaner, take care to

prevent back injury.

KREEPY KRAULY®PROWLER®910 Robotic Aboveground Pool Cleaner Installation and User’s Guide

iii

IMPORTANT WARNING AND SAFETY INSTRUCTIONS

Disclaimer of Liability

About your Pool and PROWLER 910

There are a multitude of factors that contribute to the life of your pool.

The Prowler 910 robotic pool cleaner are very passive products that will

have no impact on pool life.

Please be aware that over time, deterioration, discoloration and brittleness

of any pool ﬁnish can be caused separately by, or in combination with,

age, an imbalance in pool water chemistry, improper installation and other

factors. Robotic pool cleaners, such as the Prowler 910, will not remove

or cause wear on “good” pool plaster. In fact, the opposite is true–pool

plaster will eventually cause wear on the cleaner.

The same situation holds true for vinyl-lined in-ground swimming pools,

because vinyl liners are also affected by the environment and factors such

as pool water chemistry, sunlight and the pool’s surroundings. Therefore

over time, vinyl can become brittle and weak. In addition, vinyl-lined pools

are affected by the workmanship, composition and installation of the

liner and the workmanship and quality of construction of the supporting

walls and pool base. These are all factors which can contribute to liner

failure. The existence of any of these type of conditions in your pool is

not caused by the use or operation of the Prowler 910. The manufacturer

disclaims any liability for repairs or replacement to any of these structures

or components of the customer’s pool.

The pool owner must assume all responsibility for the condition and

maintenance of the pool’s surface, water and deck.

SAVE THESE INSTRUCTIONS

KREEPY KRAULY®PROWLER®910 Robotic Aboveground Pool Cleaner Installation and User’s Guide

Overview

Prowler®910 Robotic Pool Cleaners are designed to scrub, vacuum, and ﬁlter your aboveground pool. The Prowler

cleaner’s top loading basket ﬁltration design allows for quick removal of the ﬁlter basket and easier cleaning of the

basket. Before operating this product, be sure to read and follow all warning and safety instructions on pages ii-iii.

Cleaner Components:

• Cleaner with 40 ft. Floating Cable

• Power Supply

INITIAL SETUP AND OPERATION

Cleaner with 40 Ft.

Floating Cable Power Supply

STEP 1:

Power Supply Placement

Position the power supply at least 10 feet (3 m) from the

edge of the pool. See Figure 1.

STEP 2:

Unroll Floating Cleaner Cable

Unroll the ﬂoating cable and stretch it out completely so

that it has no kinks. See Figure 2.

Initial Setup

Before using the cleaner for the ﬁrst time, perform the following procedures:

Figure 2

Figure 1

Figure 3

STEP 3:

Connect Power Supply to Cleaner

Connect the ﬂoating cleaner cable to the power supply.

Ensure the connector notch is lined up with the

corresponding groove in the socket on the power supply.

Turn the cable connector clockwise to lock the cable into

the power supply connection. See Figure 3.

KREEPY KRAULY®PROWLER®910 Robotic Aboveground Pool Cleaner Installation and User’s Guide

Figure 4

STEP 4:

Connect Power Supply to Power Source

Connect the power supply to the electrical source/outlet.

See Figure 4.

RISK OF ELECTRICAL SHOCK OR

ELECTROCUTION: Connect only to a grounding

type receptacle protected by a ground-fault circuit-interrupter

(GFCI). Contact a qualiﬁed electrician if you cannot verify that the

receptacle is protected by a GFCI.

To reduce the risk of electrical shock, do not use

extension cord to connect unit to electrical supply;

provide a properly located outlet.

Do not switch the pool cleaner to “ON” if it is not

fully immersed in water. Operating the cleaner out

of water will immediately cause severe damage and will result in loss

of warranty. Do not leave the cleaner in the pool all the time. Always

remember to turn the power supply “OFF” and unplug it from the power

outlet before removing the cleaner from the pool.

1. Be sure the power supply is positioned at least 10 feet

(3 m) from the pool.

2. Lower the Prowler®910 Robotic Pool Cleaner into the

pool by the handle (see Figure 5).

Note: Never lower the cleaner into the pool by the

ﬂoating cable. This puts an unnecessary strain on the

cable and could result in damage to the cleaner.

3. Gently tilt the cleaner from side to side or turn upside

down to release trapped air. See Figure 6.

STEP 5:

Placing the Cleaner in the Pool

Figure 5 Figure 6

STEP 6:

Start the Cleaning Cycle

Once the cleaner is resting ﬂat on the bottom of the pool,

press the On/Off button on the power supply to begin a

cleaning cycle. See Figure 7.

The cleaner will now operate for one full cleaning cycle,

unless turned off using the On/Off button. A full cleaning

cycle will generally last 1½ hours. After the cleaner has

completed a cleaning cycle it will automatically come to a

stop.

Figure 7

KREEPY KRAULY®PROWLER®910 Robotic Aboveground Pool Cleaner Installation and User’s Guide

Removing the Cleaner from the Pool

The Prowler®910 Robotic Pool Cleaner will shut off automatically at the end of a cleaning cycle. Follow the steps below to

remove the cleaner from the pool.

1. Disconnect the power supply cable from the electrical outlet.

2. Using the ﬂoating cleaner cable, slowly and gently pull the cleaner to the waterline

at the edge of the pool until you may reach the handle. DO NOT lift the cleaner out

of the water by the cable.

3. Using the handle, lift the cleaner out of the pool. See Figure 8.

Note: Never lift the cleaner out of the pool by the ﬂoating cable. This puts an

unnecessary strain on the cable and could result in damage to the cleaner.

4. Place the cleaner on the edge of the pool and allow excess water to drain from the

cleaner body and basket.

5. Disconnect the ﬂoating cable from the power supply.

6. Store the cleaner in a covered area with the ﬂoating cable coiled.

MAINTENANCE

Ensure the power supply is turned “OFF” and disconnected from the electrical source/outlet before removing the cleaner from

the pool. Operating the cleaner out of water will immediately cause severe damage and will result in loss of warranty. Do not

leave the cleaner in the pool all the time.

Figure 8

Make sure the cleaner’s power supply is turned “OFF” and is disconnected from the electrical source/outlet before servicing

the cleaner. Moving parts may injure hands or ﬁngers if cleaner inadvertently powers on during servicing.

Cleaning the Filter Basket

Note: It is highly recommended that you clean the ﬁlter basket after each cleaning cycle. Too much debris in the ﬁlter will

restrict the suction power of the cleaner and reduce its effectiveness.

To clean the ﬁlter basket, follow the instructions given below:

Figure 9

STEP 1:

Open the Filter Cover and Remove the Basket

See Figure 9 and Figure 10.

Figure 10

Figure 11

STEP 2:

Empty and Clean the Filter Basket

Thoroughly clean the ﬁlter basket with a garden

hose. See Figure 11.

KREEPY KRAULY®PROWLER®910 Robotic Aboveground Pool Cleaner Installation and User’s Guide

Cleaning the Impeller

Always disconnect power to the cleaner before servicing, disassembly, or reassembly. Failure to do so could result in death or

serious injury to servicemen, pool users or others due to electrical shock. Read all servicing instructions before servicing the cleaner.

Every so often debris may become trapped in the Prowler®910 Robotic Pool Cleaner’s impeller. To clean out debris

trapped in the impeller opening, follow the instructions below:

STEP 2:

Remove Debris from Impeller Cover

By hand, clean as much debris as possible from the opening

of the cleaner’s impeller. See Figure 14.

Sometimes the debris may become lodged deeper in the

impeller where you can not reach it. If this is the case,

proceed to the next step to remove the impeller cover

Figure 14

STEP 3:

Unmount the Impeller Cover

Using a No. 2 Phillips-head screwdriver, remove the

two screws that hold the impeller cover in place. These

screws can be found in the bottom corners of the

impeller cover. See Figure 15.

Place the two screws to the side.

Figure 15

STEP 4:

Remove the Impeller Cover

Gently pull the impeller cover away from the cleaner

body. See Figure 16.

By hand, remove any debris that has become trapped

around the impeller.

Remount the impeller cover with two impeller cover

screws.

Figure 16

STEP 1:

Open the Filter Cover and Remove the Basket

See Figure 12 and Figure 13.

Figure 12

Figure 13

KREEPY KRAULY®PROWLER®910 Robotic Aboveground Pool Cleaner Installation and User’s Guide

Storing the Cleaner

Any time the cleaner will not be in use for an extended

period of time, for example during the winter, follow the

storage recommendations below:

• Be sure to disconnect the power supply.

• Always coil the cleaner’s ﬂoating cable.

• Store the cleaner in a protected area out of direct

sun, rain and frost, at a temperature between 5°-

45°C / 41°-113°F.

• Drain all water from the pool cleaner.

• Thoroughly clean the ﬁlter basket and ﬁlter screens

and store the cleaner with them installed.

KREEPY KRAULY®PROWLER®910 Robotic Aboveground Pool Cleaner Installation and User’s Guide

TROUBLESHOOTING

Problem Possible Cause Corrective Action

Cable twisting or cable

coils up.

Obstruction in pool

Gets stuck on main drain cover

Excess cable in the pool

Remove obstruction in pool.

Turn off ﬁlter and install main drain cover ring.

Straighten cable and lay in sun periodically.

Remove excess cable from pool.

Cleaner is moving in

circles

Dirt stuck in moving parts

Tracks worn due to extended use

Power supply positioned incorrectly

Wrong mounting of bottom lid

Algae in pool.

Remove dirt from moving parts.

Contact your dealer. Replace tracks.

Place power supply in a position so that the cleaner

can reach all walls.

Lock bottom lid in the right position.

Correct pool and water conditions.

Cleaner does not reach

all areas of the pool

Power supply positioned incorrectly

Algae on pool ﬂoor

Pool ﬁlter and pump is on

Place power supply in a position so that the cleaner

can reach all walls.

Brush pool ﬂoor.

Turn off pool ﬁlter and pump and run another

cleaning cycle.

Motor not working Impeller blocked

Drive system blocked

Electrical problem - motor unit, ﬂoating

cable, or power supply

Remove impeller tube. Clean impeller.

Clean tracks and wheels.

Consult with your dealer or service center.

Cleaner will not sink Air caught in trapped in cleaner Turn cleaner upside down under water to remove

trapped air. Wash the cartridge. Remove calcium

deposits or other chemical sediments.

Open inlet ﬂap in the bottom lid to remove dirt and/or

trapped air.

Power supply or power

supply switch light is

not working

Not plugged in properly or main socket is

damaged

Reconnect and check main power supply.

Inhaltsverzeichnis

Andere Pentair Ultraschall-Schmuckreiniger Handbücher

Pentair

Pentair KREEPY KRAULY Kruiser PRO Bedienungsanleitung

Beliebte Ultraschall-Schmuckreiniger Handbücher anderer Marken

Kränzle

Kränzle Round Cleaner 300 INOX Leitfaden

RIDGID

RIDGID 36023 Bedienungsanleitung

JOCCA

JOCCA 1249 Bedienungsanleitung

Kärcher

Kärcher FC 7 Cordless Bedienungsanleitung

Kärcher

Kärcher SB OB Bedienungsanleitung

Connoisseurs

Connoisseurs SafeWave LaSonic Bedienungsanleitung

Laser

Laser 6166 Bedienungsanleitung

poolstar

poolstar NetSpa Super Vac Bedienungsanleitung

Hammerhead

Hammerhead DCFSCP18 Bedienungsanleitung

Rothenberger

Rothenberger RODIA 1600 Bedienungsanleitung

Hedson

Hedson DRESTER X Series Bedienungsanleitung

ETEKCITY

ETEKCITY CD-2800 Bedienungsanleitung

RCBS

RCBS 87006 Merkblatt

Ryobi

Ryobi P2905 Bedienungsanleitung

Ryobi

Ryobi PBLHV704 Bedienungsanleitung

IPC

IPC Combo-C PW-C80 Bedienungsanleitung

Kärcher

Kärcher WRP 1000 Classic Bedienungsanleitung

Makita

Makita DCL280F Bedienungsanleitung