Pepperl+Fuchs HiC2842 Bedienungsanleitung
Switch Amplifier
HiC2842
<2-channel isolated barrier
<24 V DC supply (bus powered)
<Dry contact or NAMUR inputs
<2 passive transistor outputs
<Line fault detection (LFD)
<Reversible mode of operation
<Up to SIL 2 (SC 3) acc. to IEC/EN 61508
Function
This isolated barrier is used for intrinsic safety applications.
The device transfers digital signals (NAMUR sensors/mechanical contacts) from the explosion-hazardous area to the non-explosion-
hazardous area.
Each input controls a passive transistor for the non-explosion-hazardous area load.
Via switches the mode of operation can be reversed and the line fault detection can be switched off.
During a fault state, the transistors revert to their de-energized state and LEDs indicate the fault according to NAMUR NE 44. A separate fault bus
is available. This fault bus can be monitored if the termination board supports a module fault detection.
This device mounts on a HiC termination board.
Connection
Zone 0, 1, 2
HiC2842
Termination Board
I
II
I
II
10 kΩ
1.5 kΩ
10a
9a
SL1
8a
7a
12
15
11
14
24 V DC
Fault
1a, 1b
2a, 2b
6b
5a
5b
1
4
-
+
+
-
SL2
10 kΩ
1.5 kΩ
1a
1b
2
5
+
-
+
-
+
-
Technical Data
General specifications
Signal type Digital Input
Functional safety related parameters
Safety Integrity Level (SIL) SIL 2
Systematic capability (SC) SC 3
Supply
Connection SL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage Ur19 ... 30 V DC bus powered via Termination Board
Ripple ≤ 10 %
Rated current Ir≤ 30 mA
1
Release
date:
2023-06--
05 Date of
Release date: 2023-06-05 Date of issue: 2023-06-05 Filename: 214234_eng.pdf
Germany: +49 621 776 2222Pepperl+Fuchs Group
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
USA: +1 330 486 0002 Singapore: +65 6779 9091
Technical Data
Power dissipation ≤ 600 mW
Power consumption ≤ 700 mW
Input
Connection side field side
Connection SL2: 5a(+), 5b(-); 1a(+), 1b(-)
Rated values acc. to EN 60947-5-6 (NAMUR), see manual for electrical data
Open circuit voltage/short-circuit current approx. 10 V DC / approx. 8 mA
Switching point/switching hysteresis 1.2 ... 2.1 mA / approx. 0.2 mA
Line fault detection breakage I ≤ 0.1 mA , short-circuit I ≥ 6.5 mA
Pulse/Pause ratio min. 100 µs / min. 100 µs
Output
Connection side control side
Connection SL1: 8a(+), 7a(-); 10a(+), 9a(-)
Rated voltage Ur30 V DC
Rated current Ir50 mA
Response time ≤ 200 µs
Signal level 1-signal: (external voltage) - 1 V max. for 50 mA (Tamb = 25 °C (77 °F))
0-signal: blocked output (off-state current ≤ 10 µA)
Output I signal ; Transistor
Output II signal ; Transistor
Fault indication output
Connection SL1: 6b
Output type open collector transistor (internal fault bus)
Transfer characteristics
Switching frequency ≤ 5 kHz
Galvanic isolation
Output/power supply basic insulation acc. to EN 50178, rated insulation voltage of 50 V AC
Output/Output basic insulation acc. to EN 50178, rated insulation voltage of 50 V AC
Indicators/settings
Display elements LEDs
Control elements DIP switch
Configuration via DIP switches
Labeling space for labeling at the front
Directive conformity
Electromagnetic compatibility
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
Conformity
Galvanic isolation EN 50178:1997
Electromagnetic compatibility NE 21:2012
For further information see system description.
Degree of protection IEC 60529
Protection against electrical shock IEC 61140
Ambient conditions
Ambient temperature -40 ... 70 °C (-40 ... 158 °F)
Relative humidity ≤ 90 % , non-condensing
Mechanical specifications
Degree of protection IP20
Mass approx. 100 g
Dimensions 12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch) (W x H x D)
Mounting on termination board
Coding pin 1 and 2 trimmed
For further information see system description.
Data for application in connection with hazardous areas
EU-type examination certificate BVS 09 ATEX E 157
Switch Amplifier HiC2842
Release date: 2023-06-05 Date of issue: 2023-06-05 Filename: 214234_eng.pdf
2
Germany: +49 621 776 2222Pepperl+Fuchs Group
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
USA: +1 330 486 0002 Singapore: +65 6779 9091
Technical Data
Marking 1 II (1)G [Ex ia Ga] IIC
1 II (1)D [Ex ia Da] IIIC
1 I (M1) [Ex ia Ma] I
Input Ex ia, Ex iaD
Voltage Uo10.5 V
Current Io17.1 mA
Power Po45 mW (linear characteristic)
Supply
Maximum safe voltage Um253 V AC (Attention! Um is no rated voltage.)
Output
Maximum safe voltage Um253 V AC (Attention! The rated voltage can be lower.)
Galvanic isolation
Input/Output safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Input/power supply safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
Directive 2014/34/EU EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 50303:2000
International approvals
UL approval E106378
Control drawing 116-0331
IECEx approval
IECEx certificate IECEx BVS 09.0060
IECEx marking [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I
General information
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals
where applicable. For information see www.pepperl-fuchs.com.
Assembly
PWR
HiC
2842
2 ch
Digital
Input
CH1
CH2
STATUS/
FAULT
LED green:
Power supply
Front view
Place for labeling
Switch 1 ... 4
LED yellow/red:
Status output 1/
Fault at input 1
LED yellow/red:
Status output 2/
Fault at input 2
Switch Amplifier HiC2842
Release date: 2023-06-05 Date of issue: 2023-06-05 Filename: 214234_eng.pdf
3
Germany: +49 621 776 2222Pepperl+Fuchs Group
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
USA: +1 330 486 0002 Singapore: +65 6779 9091
Configuration
S1 S4
I
II
S1 S4
I
II
Open - energized
Input to output operation
Function
I
S1
CH1
Switch settings
Input fault detection
Fault enable
Fault disable
Close - de-energized
Close - energized
Open - de-energized
S2
I
II
II
I
S3
CH2
S4
I
II
II
Refer to the Instruction
Manual to install and
operate the unit
CAUTION
Configuration
Configure the device in the following way:
lPush the red Quick Lok Bars on each side of the device in the upper position.
lRemove the device from termination board.
lSet the switches according to the figure in the Configuration section.
Note
The pins for this device are trimmed to polarize it according to its safety parameters. Do not change the setting. For further information
see system description.
Switch Amplifier HiC2842
Release date: 2023-06-05 Date of issue: 2023-06-05 Filename: 214234_eng.pdf
4
Germany: +49 621 776 2222Pepperl+Fuchs Group
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
USA: +1 330 486 0002 Singapore: +65 6779 9091
Andere Pepperl+Fuchs Verstärker Handbücher
Pepperl+Fuchs
Pepperl+Fuchs SIL HiD282 Series Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs KFU8-SR-Ex1.W Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs KCD2-SR Series Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs KFA4-SR2-Ex1.W Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs FYQLA1-140R-3 Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs HiC2831R1 Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs KFD2-SOT3-Ex Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs HiD2822 Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs KFD2-SR2-Ex1.W Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs KFD2-SH-Ex1 Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs HiC283 Series Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs KFD2-SR2-Ex1.W.LB Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs HiD2824 Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs HiD2844 Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs KFD2-SR3-2.2S Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs HiC2841 Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs SIL HiC2853R1 Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs KCD2-SON-Ex Series Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs KFD2-SR2-Ex Series Bedienungsanleitung
Pepperl+Fuchs
Pepperl+Fuchs HiD2844 Bedienungsanleitung
