Perle LINKSTREAM Bedienungsanleitung

PARTNo.5500040-16

LINKSTREAM

Installation Guide

No part of this document may be copied without written permission from

Perle Systems.

The Perle policy is one of continuous development and consequently the equipment

may vary in detail from the description and specification in this publication.

LINKSTREAM

USER GUIDE

Page 3

TABLE OF CONTENTS

SECTION PAGE

1.0 GETTING TO KNOW YOUR LINKSTREAM

Documentation 4

Introduction stand alone/rack mount 4

Package contents 4

LINKSTREAM construction 5

Front panel display 5

Reset button 6

Rear panel connections and switch 6

Optional upgrades 7

ISDN2e terminal adaptor 7

User channel expansion card 7

Voice over IP 7

2.0 CONNECTING TO YOUR LINKSTREAM

Power and console connection 8

User channel connection 8

Modem cable 8

Modem controls 9

ISDN connection 9

Serial link connection 9

Ethernet (LAN) connection 10

Ethernet interface/links 10

3.0 COMMAND LINE INTERFACE 11

4.0 CONFIGURING YOUR LINKSTREAM

Quick setup 12

Cold start 14

Accessing management screens 14

Node manager screen structure 16

Statistics screen structure 17

Manual configuration 18

Internet parameters 19

Domain name server configuration 19

Ethernet configuration 20

ISDN call parameter 21

PPP interface - LCP/PAP parameters, IPCP parameters 22

Configure session parameters, System reset 23

5.0 GENERAL INFORMATION

Approvals/RFC list 24

Specification 25

This Installation/User Guide has been designed to assist in the installation of LINKSTREAM in standard

configurations. If the more advanced features of the LINKSTREAM are required then the LINKSTREAM Range

Reference Manual is available. Please contact your supplier for details.

ACKNOWLEDGEMENTS

*Ethernet is a registered trademark of XEROX

*KILOSTREAM and MEGASTREAM are registered trademarks of BT plc

*VT100 is a registered trademark of Digital Equipment Corporation Inc.

LINKSTREAM

USER GUIDE

Page 4

This User Guide gives quick set up information. For more

detailed information, the LINKSTREAM Range Reference

Manual is available.

The LINKSTREAM is a stand alone product combining

the functions of a terminal server and router in the same

unit. It consists of a metal case with an internal power

supply with 8 asynchronous ports. In addition, there is

an Ethernet port and two WAN interface connections.

The LINKSTREAM function is primarily that of a

distributed data switch working at both the wide and local

area network level. LINKSTREAM combines a host of

features providing the user with two high speed link ports

to access remote local area networks, eliminating the

need for additional bridges and routers. The two high

speed link ports operate at speeds up to 2Mbps enabling

the user to perform remote terminal multiplexing

accommodating Nx64K digital services.

LINKSTREAM is supplied in packaging specially designed

to prevent damage during transit. It is important that

the contents are checked against the list below BEFORE

installing. In the unlikely event of a damaged or missing

item please contact your supplier.

1 x LINKSTREAM unit

1xMains cable

1x User Guide

1x Console cable

GETTING TO KNOW YOUR LINKSTREAM

DOCUMENTATION

INTRODUCTION

STAND ALONE

FUNCTION

PACKAGE CONTENTS

GETTINGTOKNOWYOUR LINKSTREAM SECTION 1.0

LINKSTREAM

USER GUIDE

Page 5

The LINKSTREAM consists of a stand alone case of metal

construction with an internal power supply. Up to two

expansion cards can be fitted to provide additional user

channels, up to a maximum of 24.

The unit is supplied as standard with the following

features:

2 x Serial (WAN) ports

8 x Asynchronous user channels

3 x Ethernet LAN ports 10Base5, 10Base2 and 10BaseT.

Optional upgrade modules are available and are detailed

later in this section.

The front panel of the unit is shown below.

RUN

A green LED which flashes at a constant rate of approx.

once every second. This indicates that the power is

applied, all self checks are completed and the unit is

running normally.

LNK0

A green LED which flashes to show data transfer over

Link0. When data transfer ceases, the LED may be left in

the ON or OFF condition.

LNK1

A green LED which flashes to show data transfer over

Link1. When data transfer ceases, the LED may be left in

the ON or OFF condition.

For data transfer over the ISDN the appropriate link LED

will be permanently on.

ENET

A green LED which flashes to show data transfer over the

Ethernet interface. When data transfer ceases the LED

may be left in the ON or OFF condition.

ATTN

An amber LED which when illuminated indicates that a

fault is present or has occurred during system operation.

If lit, please contact your supplier for assistance. If unable

to do this, the fault may be due to a corruption in the

unit's configuration and it is advised that a cold start is

activated and the unit re-configured.

RUN

LNK0

ENET

ATTN

LNK1

RSET

RSRT

FRONT PANEL

LED DISPLAY

Figure 1

LINKSTREAM

front panel

LINKSTREAM

CONSTRUCTION

SECTION 1.0 GETTINGTO KNOWYOUR LINKSTREAM

LINKSTREAM

USER GUIDE

Page 6

There are also two recessed push buttons on the front

panel:

RSET This performs a 'warm start' to the system in

that it clears down all queues and restarts the

system with existing configuration parameters.

RSRT This button is used to perform a full 'cold start'

and is used in conjunction with RSET.

The rear panel of the unit provides for all connections to

the unit.

FRONT PANEL

BUTTON

GETTINGTO KNOWYOUR LINKSTREAM SECTION 1.0

Connections are:

❑Mains Power Inlet

110-240V socket outlet to be nearby and accessible.

❑0 - 23

Up to 24 user channels, 8 on the base unit and 8

on each expansion card.

❑LINK 0

Serial WAN link.

❑LINK 1

Serial WAN link.

❑ISDN

ISDN2e Terminal Adaptor

❑10b5, 10b2, 10bT

Ethernet interfaces for the various types of

Ethernet connection.

See page 9 for optional upgrades.

This rear panel switch selects the serial link and ISDN

interface.

Select 'ISDN' for ISDN.

Select 'LINK' for serial link connector.

Figure 2

LINKSTREAM

rear panel

REAR PANEL

CONNECTIONS

REAR PANEL

SWITCH

LINKSTREAM

USER GUIDE

Page 7

OPTIONAL UPGRADES LINKSTREAM - ISDN2e Terminal Adaptor

8 Channel expansion card

Voice over IP card

Configured automatically or manually, one or both of the

WAN links can be replaced with an ISDN interface running

at 64Kbps on each link. The module is plugged into rear

socket on the LINKSTREAM.

LINKSTREAM switch settings

This rear panel switch is for each serial link

Select 'ISDN' for ISDN.

Select 'LINK' for serial link connector.

The ISDN function within LINKSTREAM has been designed

to offer the same operation to the user whether the

internal ISDN module is installed or an external Terminal

Adaptor is connected to the LINK0 or LINK1 interface.

Stand alone and rackmount units are supplied with 8 user

channels. Up to 24 user channels can be supported by

the addition of LINKSTREAM expansion cards. These are

ordered separately and are fitted by the user.

The LINKSTREAM VIP card provides 2 compressed voice/

fax channels for IP networks.

SECTION 1.0 GETTINGTO KNOWYOUR LINKSTREAM

INTEGRAL ISDN2e

TERMINAL ADAPTOR

USER CHANNEL

EXPANSION CARD

VOICE OVER IP

CAUTION

INSTALLATION OF MODULES SHOULD BE CARRIED OUT

BY QUALIFIED SERVICE PERSONEL ONLY.

LINKSTREAM

USER GUIDE

Page 8

On power up, the LEDs on the front panel illuminate while

the LINKSTREAM performs system checks. Once

successfully completed the RUN LED flashes at a constant

rate (approx. once every second).

If the RUN LED does not flash at a constant rate, or the

ATTN LED is on, then do not continue with the

installation. Contact your supplier for advice.

Connect the RJ45 end of your console cable into any of

the user channels. Connect the other end of the console

cable into the serial port of your computer or terminal,

tighten the locating screws where applicable.

To make up your own console cable the RJ45 socket pin

outs are detailed in the 'User Channel Connection' section,

below.

The user channel RJ45 sockets present asynchronous

V.24/V.28 as a DCE with the following pin outs :

LINKSTREAM Terminal

RJ45 DB25 Function

1 <<-- 4 RTS

2 <<-- 20 DTR

3 <<-- 2 TXD

4 -->> 8 DCD

5 -->> 3 RXD

6 7 GND

7 -->> 6 DSR

8 -->> 5 CTS

Please ensure that user channel cables do not exceed V.24/

V.28 (RS232) recommended lengths or data corruption

can occur.

The following cable specification is typical to allow

bidirectional modem access. We recommend that you

check with your modem manual to ensure that the

specification is suitable.

LINKSTREAM Path Modem DB25

RTS 1 <<-- 22 RINGIN

DTR 2 <<-- 5 CTS

TXD 3 <<-- 3 RXD

DCD 4 -->> 20 DTR

RXD 5 -->> 2 TXD

GND 6 7 GND

CTS 8 -->> 4 RTS

POWER CONNECTION

CONSOLE

CONNECTION

CONNECTING TO YOUR LINKSTREAM

MODEM CABLE

USER CHANNEL

CONNECTION

CONNECTINGTOYOUR LINKSTREAM SECTION 2.0

LINKSTREAM

USER GUIDE

Page 9

The user channels on LINKSTREAM have 5 control lines

for modem access, 3 outputs (DCD, DSR, CTS) and 2 inputs

(RTS, DTR). The 2 inputs are monitored for call status

whilst 2 outputs (DCD and CTS) are used by LINKSTREAM

to control access. DSR is permanently 'ON' by being tied

high through a resistor.

LINKSTREAM is capable of working in 3 different modes

with a modem to suit every application :

1. Initiate call only (Dial Out)

2. Receive calls only (Dial In)

3. Bidirectional calls (Dial In/Out)

This User Guide only deals with bidirectional call set up.

Full details of configuration for each mode are available

in the LINKSTREAM Range Reference Manual.

An optional ISDN2e Terminal Adaptor (TA) can be installed

in LINKSTREAM. This can be used to replace one or both

of the WAN links with an ISDN interface running at 64Kbps

on each link.

We recommend that you configure your LINKSTREAM

before connecting the TA or serial link cable. The ISDN

cable is supplied with the TA. A second serial link cable

can be ordered separately for connection to a NTU.

MODEM CONTROLS

SECTION 2.0 CONNECTINGTO YOUR LINKSTREAM

ISDN CONNECTION

LINKSTREAM

USER GUIDE

Page 10

The following cable is used to connect to V.35 DCEs.

LINKSTREAM DCE:

15-way D plug MRAC 345-J2 Function

2 P TXD-A

9 S TXD-B

4 R RXD-A

11 T RXD-B

3 C RTS

8 B Ground

5 F DCD

1 Y TXC-A

7 AA(a) TXC-B

6 V RXC-A

13 X RXC-B

14 U TXC(Ext)-A

15 W TXC(Ext)-B

The following cable is used to connect low speed X.21bis

Kilostream or a modem with a V.24 interface.

LINKSTREAM Modem:

15-way D plug 25-way D plug Function

2 2 TXD

4 3 RXD

3 4 RTS

8 7 Signal Ground

5 8 DCD

1 15 TXC

6 17 RXC

14 24 TXC(Ext)

The 15-way D socket uses UNC 440 retention screws.

We recommend that you configure your LINKSTREAM

before connecting the Ethernet port.

Care should be taken when connecting the Ethernet port

of the LINKSTREAM to your network. Ensure that you

follow the usual precautions as laid down in the Ethernet

guidelines. If unsure of connection procedures for

Ethernet then contact your supplier for advice.

10Base5, 10Base2 and 10BaseT interfaces are provided

on the stand alone LINKSTREAM although only one may

be used at any time. Failure to observe this will corrupt

the data and prevent correct operation. Selection of the

interface is by use of the 6-way multi-coder between

column pairs as set out below:

10BaseT RJ45 Link columns A-B (factory default).

10Base2 BNC Link columns B-C

10Base5 15 way D Link columns C-D

V.35 SERIAL LINK

CONNECTINGTO YOUR LINKSTREAM SECTION 2.0

V.24/V.28 SERIAL LINK

NOTE:

ETHERNET

CONNECTION

ETHERNET

INTERFACE

LINKS

Inhaltsverzeichnis

Andere Perle Netzwerk-Router Handbücher

Perle

Perle IRG5520 Series Bedienungsanleitung

Perle

Perle PERLE P850 Bedienungsanleitung

Perle

Perle IRG7440 Bedienungsanleitung

Perle

Perle P840 Bedienungsanleitung

Perle

Perle IRG5140+ Handbuch

Perle

Perle IOLAN SDS Bedienungsanleitung

Perle

Perle IOLAN STS8D GR Bedienungsanleitung

Perle

Perle IRG5541 Handbuch

Perle

Perle P841 Bedienungsanleitung

Perle

Perle P840 Bedienungsanleitung

Perle

Perle IOLINK-520 Bedienungsanleitung

Perle

Perle IRG5140+ Handbuch

Perle

Perle P1705 Bedienungsanleitung

Perle

Perle PERLE P850 Bedienungsanleitung

Perle

Perle IRG5410 Series Handbuch

Perle

Perle IOLAN SDG4 LA/LE Handbuch

Perle

Perle IRG5410 Series Bedienungsanleitung

Perle

Perle IOLAN SDG2 LA/LE Handbuch

Perle

Perle IOLINK-520 Bedienungsanleitung

Perle

Perle IRG5000 Series Handbuch

Perle

Perle P840 Bedienungsanleitung

Perle

Perle P2600 Bedienungsanleitung

Perle

Perle IRG5140+ Handbuch

Perle

Perle IRG5541+ FN Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise