Perry Electric 1TX RX01/P Bedienungsanleitung

lm - DERXPE001 02/18

Model with burner or solenoid valve control in wireless

temperature control systems

Modèle avec commande pour chaudière ou électro-

vanne en systèmes de réglage thermique sans fils

Modell mit drahtloser Steuerung für Durchlauferhitzer

oder Elektroventil in Heizanlagen

Modello con comando per caldaia o elettrovalvola in

impianti con sistema di termoregolazione senza fili

Modelo para controlar calderas o electroválvulas en

instalaciones de termorregulación sin cables

1 ZONE WALL MOUNTING RADIO RECEIVER

RECEPTEUR RADIO 1 ZONE POUR MONTAGE EN SAILLIE

FUNKEMPFÄNGER 1 ZONE WANDMONTAGE

RICEVITORE RADIO 1 ZONA DA PARETE

RECEPTOR RADIO DE 1 ZONA DE PARED

IT - Italiano

DE - Deutsch

FR - Français

EN - English

ES - Español

DATI TECNICI - ISTRUZIONI PER L’INSTALLATORE

- MESSA IN FUNZIONE E IMPIEGO

TECHNICAL SPECIFICATIONS - INSTRUCTIONS FOR

THE INSTALLER - PUTTING INTO OPERATION AND USE

DONNÉES TECHNIQUES - INSTRUCTIONS POUR

L’INSTALLATEUR - MISE EN MARCHE ET UTILISATION

TECHNISCHE DATEN - NORMEN FÜR DIE INSTALLATION

- INBETRIEBNAHME UND GEBRAUCH

DATOS TÉCNICOS - INSTRUCCIONES PARA EL

INSTALADOR - PUESTA EN FUNCIONAMIENTO Y USO

Page 3

Page 13

Seite 23

Pagina 33

Página 43

TECHNICAL SPECIFICATIONS

ENGLISH

Supply voltage: 230 V~ 50-60 Hz

Device Absorption: 2,5 VA max

Type of action, disconnection and appliance: 1/B/Electronic

Type of Output: 1 relay with unipolar changeover contact NC/NO/COM,

voltage-free 5(2) A / 250 V~

Wire section at terminals: min. 1 mm ÷ max. 2.5 mm

Reception frequency : 868 MHzband " -868.6"

Maximum signal capacity in free air: 120 m

Maximum signal capacity in the presence of walls: 30 m (according to the chap. 1.1 and to the chap. 1.4)

Signal reception mode: antenna internal to the receiver

Type of insulation: Class II

Protection degree: IP30 / wall-mounted

Pollution: normal

Operating temperature limits: -20 °C ÷ +70 °C

Storage temperature limits: -25 °C ÷ +85 °C

PERFORMANCE DATA

!Coupling transmitters in self-learning mode, facilitated by luminous and audio signals.

!It is possible to erase a transmitter coupling to the zone even in the event of transmitter failure.

!Manually forcing the state of the output to test the system (5 minutes, resettable).

!“RESET“ command to erase temporary data in memory and deactivate commands.

!Permanent modifiable memory for transmitter couplings.

!Luminous signals indicating malfunctions due to the absence of transmission or an almost dead battery

!Highly reliable communications thanks to the double transmission of data.

!Lighted and/or audio signal, on 3 levels, of the TEST signal to verify the presence and capacity of the signal (VMETER)

1 - INSTRUCTIONS FOR THE INSTALLER

DIMENSIONS

RESET

133

RESET

Burner

Receiver

Chronothermostat

Fig. 1.i

INSTALLATION EXAMPLE

RESET

INSTALLATION

Fig. 2.i

1.1 - INSTRUCTIONS AND REQUIREMENTS FOR INSTALLING THE RECEIVER

Install the receiver at a height that allows the antenna to stick up above any nearby metal container (boiler, expansion tanks, metal

cabinets); avoid positioning the antenna near cables and electrical panels (fig. 1.i - fig. 2.i)

Cabinets, walls and slabs containing metal can limit the operation of the product.

This system is incompatible with radio products a working on the same frequency using permanent

emission mode.

Instructions relative to the structure of realizable systems and the assignment of areas to individual timer-thermostats or

thermostats are shown in the technical documentation for the transmitter devices (chronothermostats and/or thermostats).

Important: installation and electrical connections of devices and appliances must be implemented only by a qualified

electrician and in compliance with current regulations. The manufacturer declines any liability in connection with the use of

products subject to special environmental and/or installation standards. The examples shown in this document are of principle.

Fig. 3.i

RESET

Fig. 4.i

Fig. 5.i

D= Catches for locking the

front to the base

Removable area for the

passage of wires

(Installation with built-in box)

Removable areas for

installation with trunking

System.

1.2 - INSTALLING THE BASE ON THE WALL

Installing the device: INDEPENDENT - FIXED

ATTENTION: INSTALLATION MUST BE PERFORMED AFTER SECTIONING

THE MAINS SUPPLY - 230 V~.

For installation, it is necessary to separate the front part, complete with

electronic card, from the base.

!First on one side and then on the other, insert a screwdriver in the slots

located on the sides of the product, exerting light pressure on the locking

catch, then, with a small forward rotation of the screwdriver (as shown in

figure 3.i), lift the front.

!Remove the front from the base (the resistance to removal is due to the

coupling pin on the terminal strip) fig. 4.i.

From the base, remove the parts prepared for the passage of the connection wires shown in fig. 5.i.

!Pass the connection wires through the opening you have made.

!Attach the base to the wall (or built-in box), with 2 screws using the pairs of holes provided (fig. 5.i).()A-A, B-B, C-C

!Make the electrical connections to the terminals located on the base as shown in the next chapter.

Open

L1 L2N

230 V~

2536

Example of a motorized

solenoid valve connection

- 3-wire

Example of a solenoid

valve connection - 2-wire

Example of a burner

connection

Burner

Solenoid valve

Receiver

Receiver Fig. 8.i

Fig. 7.i

Fig. 6.i

1.3 - ELECTRICAL CONNECTIONS

SWITCH MAINS SUPPLY 230 V~ OFF

With reference to figures 6.i, 7.i and 8.i:

Make the connection to the mains supply

terminal = NEUTRAL1

terminal = LINE2

Make the connections to the device to be controlled

(Such as: a burner, pump, or 2 or 3-wire motorized solenoid valve, servomotor)

Terminal = line, available for controlling the load3

terminal = contact normally closed4

terminal = contact normally open5

terminal = common6

NOTES AND INSTRUCTIONS FOR THE INSTALLER

!Also pay careful attention to the instructions for the device being

controlled.

!In the presence of loads with absorption higher than the data on the

product rating plate, interpose a power relay or a suitably

dimensioned contactor. In the presence of highly inductive loads

we recommend connecting an RC filter in parallel with the load.

!When making the electrical connections, in the case of a wall

installation without built-in box, pay particular attention that the

cabling is properly placed and does not interfere with the correct

closing of the front on the base.

!In the case of installing the receiver on a metal wall, use double

insulated cables for the electrical connections.

Fig. 9.i

RESET

Semi-hole: seat for vertically placed antenna

Fig. 10.i

Antenna factory position

RESET

1.4 - ATTACHING THE FRONT WITH CARD TO THE BASE

!Reinsert the front part with card on the base being careful to

correctly insert the pins connecting the card to the terminals.

!Push the front on to the base using both hands as shown in figure

9.i, until the catches click and lock the front to the base.

ATTENTION: IN THE EVENT THAT, DUE TO ENVIRONMENTAL CONDITIONS, YOU DETECT AN EXCESSIVELY LOW RADIO

SIGNAL, WE RECOMMEND MOVING THE ANTENNA OUTSIDE THE RECEIVER AND POSITION IT VERTICALLY.

With reference to the installation procedure (chapter 1.2):

!SWITCH MAINS SUPPLY 230 V~ OFF

!Open the receiver

!Move the antenna wire from its seat (upper inside part of

the front) and rotate it vertically

!Pass the wire through the small semi-hole provided for the

purpose (fig. 10.i)

!Carefully reclose the receiver (fig. 9.i - fig. 10.I)

!Switch on power 230V~

Power the receiver and attempt to operate it and couple the

transmitter, as shown in chapter 2 “PUTTING INTO OPERATION

AND USE.”

2 - PUTTING INTO OPERATION AND USE

2.1 - SIGNAL AND COMMAND LEGEND

RESET

LED ON:

lit = power present

intermittent = transmitter malfunction

VMETER:

LED indicating the intensity of

the received radio signal

Key “ ” - Command

- Channel

“RESET” key

Fig. 1

Place for label

Fig. 2

1 s

on off

Off

Fixed on

Fixed off

1 prolonged impulse

Intermittent (t on = t off)

every second

LED

Appearance of the lighted signals

Prolonged sound

Short sound

Audible signal

n° s

LED ““- Command status

- Channel status

5 s

5 minutes

Fig. 3 Fig. 4

RESET

Fig. 5

2.2 - NEW DEVICE

When turned on, the receiver has only the lit.ON LED

N.B.: lowerThere may be a weak lighted signal on the of the , due to the presence of radio interference.LED VMETER

2.3 - TEMPORARILY FORCING THE STATE OF THE CONTROL OUTPUT (for example, to test the system)

B) TRANSMITTER COUPLED AND HEAT REGULATION ACTIVE

The above-indicated operations can also be performed, using the same methods, during normal heat regulation operation; in this case,

the temporary forced control will cause the transmitter to be excluded and the reversal of the command status: if active, it will be

deactivated and vice versa. During the forced state, the “ ” is not functional.key

Cancelling the temporary forcing of the control

!Briefly press the ; when released the temporary forced control is“”Reset key

cancelled (fig.5).

N.B.: ResetBefore performing this operation, consult chapter 2.9 “”

A) TRANSMITTER NOT YET COUPLED OR NOT ACTIVE

!Hold down the “ ” until there is a brief audible signal, then release it: the control is activated and the corresponding iskey LED

steady on (fig.3).

The control will remain activated for 5 minutes, at the end of which, an audible signal will continue for to alert the operator of5 seconds

its imminent deactivation (fig.4): if you wish to keep it active, press the “ ” again while the audible signal is sounding;key

otherwise, when the signal ceases, the control will be deactivated.

Fig. 6

Fig. 7

Fig. 8

2.4 - COUPLING TO A TRANSMITTER

Activate the “Test” state on the transmitter to be coupled, as explained in the chapter in the“”Coupling to the receiver

transmitter manual.

ON THE RECEIVER

The “ ” is offLED (receiver not coupled)

!Hold the “ ” pressed until you hear a single audible signal; then let go:key LEDthe

will flash (fig.6).

The transmitter is coupled to the receiver.

Deactivate “Test” mode ON THE TRANSMITTER, as explained in the specific chapter of

the transmitter manual.

Deactivate “Test” mode ON THE TRANSMITTER, as explained in the specific chapter of the transmitter manual.

ATTENTION: Resetthe coupling status is stored in permanent memory and is not erased by the command or by a power failure.

N.B.: test mode on the transmitter automatically terminates 3 minutes from activation.

A) - FIRST COUPLING TO A TRANSMITTER

ATTENTION: LEDif the “ ” is flashing at the beginning of the operation it means

that the transmitter in “ ” mode has already been coupled to the receiver. To confirmTest

the coupling: deactivate “ ” mode on the transmitter.Test

To cancel the coupling: hold down the “ ” until you hear a single beep; thenkey

release it; (fig.7).the is off Deactivate “ ” mode on the TRANSMITTER.LED Test

ON THE RECEIVER

The “ ” is steady onLED (receiver already coupled to another transmitter)

!Hold the ” pressed until you hear a single beep; then release it:“ the iskey LED

flashing (fig. 8).

The new transmitter is coupled to the receiver.(in “Test” mode)

B) - SUBSEQUENT TRANSMITTER COUPLINGS (such as: replacing the transmitter)

Inhaltsverzeichnis

Sprachen:

Andere Perry Electric Empfänger Handbücher

Perry Electric

Perry Electric 1TX RX0801/P Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung