Philips QT4014 Bedienungsanleitung
User manual
QT4015,
QT4015,
QT4014,
QT4013,
QT4011
1
4
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips
offers, register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Trimming comb
2 Cutting unit
3 Precision Zoom Lock™ adjustment ring
4 On/off slide with battery indicator
5 Socket for appliance plug
6 Pouch
7 Brush
8 Appliance plug
9 Adapter
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
- Make sure the adapter does not get wet.
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
- This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
- Children should be supervised to ensure that they
do not play with the appliance.
ENGLISH
Caution
- Never immerse the appliance in water or rinse it
under the tap. Only the cutting unit can be rinsed
under the tap.
- Use, charge and store the appliance at a
temperature between 5°C and 35°C.
- Only use the adapter supplied.
- If the adapter is damaged, always have it replaced
with one of the original type in order to avoid a
hazard.
- This appliance is only intended for trimming
the human beard. Do not use it for any other
purpose.
- Do not use the appliance if the cutting unit or the
trimming comb is damaged or broken, as this may
cause injury.
Electromagnetic elds
This Philips appliance complies with all standards
regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this
user manual, the appliance is safe to use based on
scientic evidence available today.
General
- The appliance is equipped with an automatic
voltage selector and is suitable for mains
voltages from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
ENGLISH 5
Charging
Charge the appliance fully before you use it for the
rst time.
It takes approximately 1 hour to fully charge the
appliance.
When it is fully charged, the appliance has a cordless
operating time of up to 60 minutes.
Note:You can use the appliance cordless as well as
connected to the mains.
1 Make sure the appliance is switched off.
2 Insert the appliance plug into the appliance.
3 Put the adapter in the wall socket.
,The charging light starts to ash green to
indicate that the appliance is charging.
,When the battery is fully charged, the charging
light lights up green continuously.
After 30 minutes, the charging light goes out.
4 After charging, remove the adapter from the
wall socket and pull the appliance plug out of
the appliance.
Battery low
When the battery is almost empty (when there are
only 5 or fewer trimming minutes left), the charging
light ashes orange.
Optimising the lifetime of the rechargeable
battery
When you have charged the appliance for the rst
time, we advise you to use it until the battery is
completely empty. Continue to use the appliance
until the motor almost stops running during a
session. Then recharge the battery. Follow this
procedure at least twice a year.
ENGLISH6
Using the appliance
Always comb the beard and/or moustache with a
ne comb before you start trimming.
When you trim for the rst time, be careful.
Do not move the trimmer too fast. Make smooth
and gentle movements.
Trimming with comb
1 Turn the Precision Zoom Lock™adjustment
ring to the desired setting.The selected setting
is the setting in the centre of the adjustment
ring.
See the table below for an overview of
the settings and the resulting hair lengths.
Setting Resulting hair
length
Setting Resulting hair
length
. 0.5mm . 5.5mm
1 1mm 6 6mm
. 1.5mm . 6.5mm
2 2mm 7 7mm
. 2.5mm . 7.5mm
3 3mm 8 8mm
. 3.5mm . 8.5mm
4 4mm 9 9mm
. 4.5mm . 9.5mm
5 5mm 10 10mm
3•
4••1
2
ENGLISH 7
Note: When you trim for the rst time, start at the
highest setting (10) to familiarise yourself with the
appliance.
2 Switch on the appliance.
3 To trim most effectively, move the trimmer
against the hair growth direction. Make sure
the surface of the comb always stays in contact
with the skin.
4 If a lot of hair has accumulated in the beard
trimming comb, remove the comb and blow and/
or shake the hair out of it.The selected setting
does not change when you do this.
Trimming at the unique ‘stubble look’
setting
1 To create a ‘stubble look’, trim with the beard
trimming comb set to setting 1.
Trimming without comb
Use the trimmer without beard trimming comb to
trim full beards and single hairs.
Be careful when you trim without comb because
the cutting element removes every hair it touches.
1 Pull the beard trimming comb off the appliance
as shown in gure 8.
2 Switch on the appliance.
ENGLISH8
3 Make well-controlled movements.Touch the
hair lightly with the trimmer.
Corded trimming
If the battery is low, you can also use the appliance
from the mains:
1 Switch off the appliance, insert the adapter in
the wall socket and wait a few seconds before
you switch on the appliance.
Cleaning
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as alcohol, petrol or
acetone to clean the appliance.
1 Make sure the appliance is switched off and
disconnected from the mains.
2 Wipe the housing of the appliance with a dry
cloth.
Never immerse the appliance in water or rinse it
under the tap.
3 Remove the trimming comb and clean it with
the brush.
4 Remove the cutting unit by pushing against the
teeth of the cutting unit and clean it with the
brush or rinse it under the tap.
ENGLISH 9
5 Shake off excess water and place the cutting
unit back by inserting the lug of the cutting unit
into the guiding slot.
6 Push the cutting unit back onto the appliance
(‘click’).
Replacement
Only replace a worn or damaged cutting unit with
an original Philips cutting unit, available from
authorised Philips service centres.
1 Open the cutting unit.
2 Remove the old cutting unit by pushing against
the teeth of the cutting unit.
3 Insert the lug of the new cutting unit into the
guiding slot.
4 Push the cutting unit back onto the appliance
(‘click’).
ENGLISH10
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Sprachen:
Andere Philips Elektrorasierer Handbücher
Philips
Philips HQ7870/19 Bedienungsanleitung
Philips
Philips 1180X/40 Bedienungsanleitung
Philips
Philips Bikini Perfect HP6364 Bedienungsanleitung
Philips
Philips HQ586 Bedienungsanleitung
Philips
Philips OneBlade QP2630 Bedienungsanleitung
Philips
Philips QG3150 Bedienungsanleitung
Philips
Philips AccuTrim T765 Bedienungsanleitung
Philips
Philips BT3237 Bedienungsanleitung
Philips
Philips YS534 Bedienungsanleitung
Philips
Philips NORELCO PT734 Bedienungsanleitung
Philips
Philips OneBlade QP2531 Bedienungsanleitung
Philips
Philips HS8460/75 Betriebsanleitung
Philips
Philips QS6160 Bedienungsanleitung
Philips
Philips QT4060 Philishave Bedienungsanleitung
Philips
Philips SW5700 Bedienungsanleitung
Philips
Philips HQT360/60 Bedienungsanleitung
Philips
Philips HQ7740 Bedienungsanleitung
Philips
Philips Norelco 7345XL Bedienungsanleitung
Philips
Philips HQ 7240 Bedienungsanleitung
Philips
Philips BT405 Handbuch
