Philips 32HF7543 Bedienungsanleitung

2005 HF Series User’s Manual 112505.0959

32HF7543 -37HF7543 –42HF7543 -User’s Manual

2005 HF Series User’s Manual 112505.0959

SAFETY INFORMATION

•Disconnect mains plug when:

Øthe red light below the TV screen is flashing continuously.

Øa bright white line is displayed across the screen.

Øcleaning the TV screen. Never use abrasive cleaning agents. Use a slightly

damp chamois leather or soft cloth.

Øthere is a lightning storm.

Øthe set is left unattended for a prolonged period of time.

•No open flame sources, such as lighted candles, should be placed on or near the TV.

•Do not place your TV set under direct sunlight or heat.

•Leave at least 1/4” around each side of TV set for sufficient ventilation to avoid over-

heating.

•Avoid placing set where it is likely to be exposed to rain or water (e.g. near the

window).

•No objects filled with liquids should be placed on top the TV in order to avoid

dripping or splashing of liquids into the set.

USEFUL TIPS

•Do not leave the television off (in standby mode) for a prolonged period of time.

•Do not re-position the television while it is switched on. Non-uniformity in screen

color may result.

•Never attempt to repair a defective TV yourself. Always consult skilled service

personnel.

2005 HF Series User’s Manual 112505.0959

Before Calling Service

A list of common symptoms is presented as follows. Before you call for service, perform

these simple checks. Some of these symptoms can be readily corrected. Note: Please

become familiar with the commercial features as described in TV Installation / Setup,

because the effects of several of these features, if they are not thoroughly understood,

might appear as faulty operation.

Symptom Possible Corrective Action

TV does not respond to commands (volume,

channel, power), or cannot be turned on if it is off,

or cannot be turned off if it is on.

Check commercial TV setup (TV installation /

setup) menu settings, including power forced on,

front keypad lockout, channel ring, volume

maximum features.

TV turns off by itself •TV automatically turns off afterwhen no RF

signal is present.

•Check Energy Saving Programmability setting

(see ESP) in TV installation / setup.

No power

Verify that the TV’s AC power cord is plugged into

the mains socket. If there is still no power,

disconnect plug. Wait for 60 seconds and re-insert

plug. Switch on the TV again.

No picture •Check antenna connection at rear of the TV.

•Possible TV station problem. Try another

channel.

Picture ok, no sound. •Try increasing the volume.

•Check that the sound is not muted. If it is

muted, press the Mute button on the remote

control to restore sound.

•Check the MAX VOLUME settings in the

setup menu

Sound ok, but poor color or no picture Check picture adjustments (brightness, contrast,

color, tint).

Snowy / noisy picture •Check antenna, cable, and/or set-top box

connections and antenna / cable.

•Possible electrical interference from appliances

or other sources.

Double images / “ghost” images Check antenna, cable and/or set-top box.

Television does not respond to remote control. •Check batteries.

•Aim remote control handset directly at remote

control sensorlens on the TV.

Channel Change to digital channels is slow The first time a digital channel is tuned, the tuning

time will be slow as information embedded in the

signal is processed. After that digital channel

tuning will be faster.

Note: These televisions are shipped in commercial mode with the processing of PSIP Virtual Channel

Table (VCT) disabled. To enable PSIP VCT processing,see the Hotel Mode Menu section.

2005 HF Series User’s Manual 112505.0959

Basic Television Connection

Antenna Connection

• Connect the antenna or RF cable signal

to the 75-ohm RF ‘F’ connector socket

located on the TV’s rear jack panel.

Mains Connection

• Verify that the mains voltage and

frequency are correct. Please refer to the

product labeling and documentation.

Note: The power button on the front panel

does not disconnect the television from the

AC mains; it toggles the

TV’s power mode

between on and standby. To completely

remove AC mains power, you must unplug

the AC mains plug.

Switching on the Set

• Press the power button on the TV’s front

panel or on the remote control to switch on

the set.

Note 1: If the TV is

in commercial mode, it

might not respond to the front panel or the

remote control, depending upon the TV’s

mode and setup configuration. Please refer

to the section TV Installation and TV

Setup Menu in this documentation for

more information.

Note 2: See

Mains Connection, above.

2005 HF Series User’s Manual 112505.0959

Use And Care of Remote Control

REMOTE CONTROLS

The following remote controls are applicable to the Philips’ HF-series television

products. These can be used for guest control functions and setup and configuration

purposes.

RC2888/01 RC2573GR

Guest Remote Setup Remote

(Optional)

To load the supplied batteries into the remote

control:

-Remove the battery compartment lid

from the back of the remote control.

-Insert the correct type of batteries into

the compartment.

-Ensure that the (+) and (-) ends of the

batteries are placed in the correct positions.

-Re-attach the battery compartment lid.

Note: Always remove the batteries from the

remote control if it is not to be used for a long

period. This can help prevent damage to the

remote from possible battery leakage.

2005 HF Series User’s Manual 112505.0959

A Guest Remote may be used to access a limited menu and to perform the basic

control functions of the television. Remote control RC2573GR is an optional remote

control specifically for configuring Institutional TV / Business Display Solutions features

and SmartCard settings. Refer to the documentationfor the RC2573GR for detailed

information. Remote controls are optional accessories for all HF-series products and must

be purchased separately.

When the RC2573GR in is setup mode and RECALL is pressed, information

similar to belowwill appear on the TV screen. This information describes the TV chassis

firmware version, diagnostic codes, setup information, and other service and technical

data regarding the television configuration.

Line 1 showsthe SmartPort Processor part number. Line 2 showsthe software

version number. Line 5 showsthe model number of the set (no distinction is made on

screen size). Lines 3, 4, 6 are blank. Line 7 shows the communication mode (always SP-

SPI for these models) and the status of the SmartPort, either online or offline. Line 8

showsthe source or channel that has been selected and if a signal is detected on that

source (Tuned or Not Tuned). Below is an example screen:

01 3104 337 01381

02 IJ5U1-1.0

05 MODEL xxHF7543 / 37

07 COMMUNICATION SP-SPI ONLINE

08 TV 3 TUNED

2005 HF Series User’s Manual 112505.0959

GUEST REMOTE CONTROL KEYS

Standby

Press to s

witch

the TV off.

DVD PLAY

To Start DVD playback

(if applicable)

DVD FAST

FORWARD

To Fast Forward DVD

playback (if applicable)

Close Caption

To activate Close

Caption functionality

DVD STOP

To Stop DVD

playback

(if applicable)

DVD PAUSE

To Pause DVD playback

(if applicable)

Smart Keys

To select

predefined picture

and sound settings.

Sleep

Activates the sleep timer.

Press repeatedly to

increment the countdown

time with 15 minutes.

+ Vol -

To adjust the volume.

Mute

Interrupt the sound or

restore it.

0/9 Digit keys

To select a TV channel.

For a two digit program

number, enter the second

digit before the dash

appears.

+ CH –Channel

Selection

To move up or down a TV

channel.

Formats

To adjust TV

screen formats

Alternate Channel

To toggle between

alternating channels

To call up or exit the

menus.

DVD Rewind

Rewind DVD playback

(if applicable)

Source Select

To toggle between

available video sources

CH Guide

activate Channel

Guide functionality

2005 HF Series User’s Manual 112505.0959

TV Setup Main Menu

SETUP

LANGUAGE ENGLISH

COMMUNICATION >

CHANNEL INSTALL >

SWITCH ON / OSD >

SECURITY >

CONTROL >

CLOSED CAPTION >

•To enter, press “M” on the RC2573GR setup remote control.

•To scroll through the menu, press (cursor up / down) on the remote

control. A highlight indicates that the respective menu item’s setting is selected for

modification.

•To modify the setting of the selected menu item press (cursor left /

right).

•To exit, press “M” on the RC2573GR setup remote control.

TV Setup Menu and Sub-Menus

LANGUAGE (English / Espanol / Francais)

When you first enter the TV SETUP menu, LANGUAGE is highlighted. You can scroll

to the LANGUAGE item. Select the desired language with cursor left or cursor right.

COMMUNICATION

COMMERCIAL MODE YES/NO

COMMERCIAL MODE

COMMERCIAL MODE is normally YES during typical operation in BDS Television

applications. When Commercial Mode is NO, the television’s Hotel Mode Menu may be

accessed. The user sends the sequence 3 1 9 7 5 3 MUTE to invoke the hotel mode sub-

menu.

2005 HF Series User’s Manual 112505.0959

The specific steps for entering Hotel Mode Menu, setting Hotel Mode to No, making

changes to the consumer set and then reversing the process are as follows:

1. Using RC2573GR setup remote, enter setup menu

2. Go to “Communication” item and right arrow to select

3. Set “Commercial Mode” to No

4. Exit setup menu (press “M” twice)

5. Press sequence 3,1,9,7,5,3, mute to enter “Hotel Mode Menu”

6. Set Hotel Mode to No

7. Scroll down to Store, press right arrow to go to “Store” on the right side of screen.

Press “F” button to get “Store Completed”

8. Remove AC power from set for at least 5 seconds

9. Power on set. Set is now in consumer mode and changes can be made to the non-

commercial settings.

10. When finished with consumer settings, press sequence 3,1,9,7,5,3, mute to enter

“Hotel Mode Menu”

11. Set Hotel Mode to yes, scroll down and ensure PSIP** is set to desired setting. Scroll

down to Store, press right arrow to go to “Store” on the right side of screen. Press

“F” button to get “Store Completed”

12. Remove AC power from set for at least 5 seconds and then restore AC power to set.

Set is now back in Hotel mode

13. Wait about 10 seconds (you will hear a click around that time), then press power

button on setup remote (in setup mode)

14. Wait a few seconds and press “M” to invoke menu.

15. Go to “Communication” item and right arrow to select

16. Set “Commercial Mode” to Yes

17. Exit setup menu (press “M” twice)

18. Press power button on setup remote to turn set off and then turn back on to ensure

settings are saved.

19. Set should now work as a commercial set

** ATSC digital terrestrial broadcast channels sendinformation along with the television signal that is

known as PSIP information. PSIP information contains data such as the channel numbers that will

normally be seen by the viewer of the channel. These channels are virtual channels meaning the channel

numbers displayed may not represent the channel numbers where the signals are physically located.In

normal viewing of ATSC signals by consumers, these virtual channels are used when tuning. However, in

some commercial applications there is a desire not to use virtual channels and instead use the physical

channel numbers when tuning.

The Hotel Mode Menu allowsthe selection of“PSIP”to either Yes or No. Setting PSIP to Yes means that

the PSIP Virtual Channel Tables will be processed and used when tuning digital signals. Setting PSIP to

No means PSIP Virtual Channel Tables will not be processed and digital channels will be tuned using the

RF channel location and MPEG program numberas defined in PAT/PMT.

2005 HF Series User’s Manual 112505.0959

CHANNEL INSTALL (>)

The CHANNEL INSTALL menu allows the user to configure the channels that can be

accessed. When installing the channels, different inputs can be mapped to TV channels to

allow seamless integration into the channel map. The two sections below explain how to

install analog channels and AV inputs, and how to install digital channels.

Installing Analog channels

When selected, CHANNEL INSTALL menu appears as follows. Configure the inputs

and channels as described.

CHANNEL INSTALL

CHANNEL TV1–125

SOURCE ANALOG/DIGITAL / AV 1 / AV 2 /HDMI 1/HDMI 2/

SIDE AV

RING SAVED

LABEL

( ) >

AUTO INSTALL TV >

•CHANNEL:

Select the channel you wish to configure.

•SOURCE:

Select the input source that you wish to associate with the specified CHANNEL. This

feature enables you to “map” (re-assign) a numeric channel number to a video input,

rather than to its normal RF TV channel (i.e. ANALOG). In other words, TV channel

2 could be used to select the AV 1 video input instead of RF (ANALOG) channel 2.

Special instructions for mapping digital channels are included below.

•RING:

Specify whether the current channel or input is to be SAVED to or DELETED from

the channel ring (i.e., list of channels available for selection by means of a standard

guest remote control).

•LABEL:

Input a maximum of 8 characters for the channel’s label. Cursor to the right to start

the first character. Cursor left or right to navigate between character positions within

the label field. Cursor up or down to select characters from the list:A to Z, 0 to 9, -, .,

/, :, =, ?, ;, <, >, @ or space. To edit, re-input the character at its position. To exit,

press “M” to navigate out of the label editing field.

•AUTO INSTALL TV:

When AUTO INSTALL TV is selected, the TV performs an automatic search for the

presence of viable RF analog signals at its tuner input. Channels 1through 125 will

be checked. When a viable signal is detected on a given channel, that channel is

added to the channel ring. Any command from a remote control terminates the AUTO

PROGRAM session.

Andere Handbücher für 32HF7543

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philips Flachbildfernseher Handbücher

Philips

Philips FTR9952/69C Bedienungsanleitung

Philips

Philips Cineos 50PF9631D Bedienungsanleitung

Philips

Philips 42HF9320A Bedienungsanleitung

Philips

Philips 20PFL4122/93 Bedienungsanleitung

Philips

Philips Matchline 50FD9935/01S Bedienungsanleitung

Philips

Philips 23PFL5522D Bedienungsanleitung

Philips

Philips 19PFL5422D Bedienungsanleitung

Philips

Philips 17PF9945 - annexe 3 Bedienungsanleitung

Philips

Philips 23PF8946M/78 Bedienungsanleitung

Philips

Philips 32PFL7602D - annexe 1 Bedienungsanleitung

Philips

Philips 29PT8618 Bedienungsanleitung

Philips

Philips 37PF3321/10 Bedienungsanleitung

Philips

Philips 23PF4310 Bedienungsanleitung

Philips

Philips Cineos 42PF9830 Bedienungsanleitung

Philips

Philips 37PF9731D Bedienungsanleitung

Philips

Philips 42PF7420 Bedienungsanleitung

Philips

Philips 32PFL7332D Bedienungsanleitung

Philips

Philips 42PFL2302/62 Bedienungsanleitung

Philips

Philips 50PF7320 Bedienungsanleitung

Philips

Philips 36PW9525 - annexe 1 Bedienungsanleitung

Philips

Philips 42PFL5578/V7 Bedienungsanleitung

Philips

Philips 40PFL8664H Bedienungsanleitung

Philips

Philips 26PFL5322 Bedienungsanleitung

Philips

Philips Matchline 42PF9996/37 Bedienungsanleitung

Beliebte Flachbildfernseher Handbücher anderer Marken

Samsung

Samsung LT-P326W Bedienungsanleitung

Sony

Sony WEGA KE-50XBR900, KE-42XBR900 Bedienungsanleitung

JVC

JVC LT-26DX7BFN Bedienungsanleitung

Samsung

Samsung CT2Z45 Bedienungsanleitung

Samsung

Samsung LNR1550X Bedienungsanleitung

Westinghouse

Westinghouse TX-42F970Z Bedienungsanleitung

Toshiba

Toshiba 32BV500B Bedienungsanleitung

Samsung

Samsung Smart TV UN55D6000 Leitfaden

RCA

RCA MR53R400 Bedienungsanleitung

JVC

JVC GGT0362-001A-H Bedienungsanleitung

Sanyo

Sanyo FVM4212 Bedienungsanleitung

JVC

JVC LT-32Z48 Bedienungsanleitung

Sony

Sony KE-42XBR900 - 42" Xbr Plasma Wega™ Integrated... Gebrauchsanweisung

Vizio

Vizio M190MV Gebrauchs- und Pflegehandbuch

Samsung

Samsung UN55F7050AF Bedienungsanleitung

RCA

RCA TruFlat F20TF30 Bedienungsanleitung

Samsung

Samsung LW32A33W Kurzanleitung

Sony

Sony FD Trinitron Wega KV-30HS420 Bedienungsanleitung