Philips BGP300 Bedienungsanleitung

Installation Instruction

Type : BGP300

Lamp : LED

Net Weight : 4 kg Approx

Voltage : 240 V, 50 Hz

Max. Projected Area : 0.16 m²

IP Classification : IP 66

CCT : 5700 K, 4000K, 3000 K

Application : Outdoor only

IP-66

Outdoor Luminaire

TOWN GLOW

Caution: Mounting to be done using M8 Grub Screw(3x).

Warranty void if Earthing is not connected.

Installation Instruction

All the pictures in the MI sheet are representative only and may vary from the Actual Product.

Outdoor Luminaire

TOWN GLOW

All the pictures in the MI sheet are representative only and may vary from the Actual Product.

IK-10

4. Use Surge protection (upto 10kV) to protect against surges/Use Type B+C surge type SPD in

distribution box to arrest switching and lighting surges.

6. Carefully re-install all seals and gaskets when servicing the luminaire.

CAUTION

1. Ensure Earthing is connected in right manner.

FAILURE OF PRODUCT DUE TO NON COMPLIANCE TO ANY OF THE ABOVE, VOIDS WARRANTY

2. Cable Entry gland should be properly tightened.

3. Product should be operated between 120-270V A.C.

5. The light source of this luminaire is not replaceable, when the light source reaches

its end of life the whole luminaire shall be replaced.

Signify Innovations India Limited

1. 2.

5. 6.

3. 4.

Fig. 1

Take the Luminaire out of the packing Box.

Unscrew the M4x8 Retainer Screw to open the

driver cover and to have access to the electrical

connections.

Note: Driver cover has Self retaining screws.

Fig. 2

Firstly, remove the LED Engine connections. Care

to be taken through out the process to not to

create any type of pull force on any of the LED

Engine wires.

Then, loosen the three M4 screw slightly, then

rotate the gear tray in ant-clockwise direction and

take the gear tray out of the housing.

Rotate the driver gear tray in clockwise direction to lock

the gear tray in between screws, then, fix it by tightening

the loosen screws

Fig.4

Fig. 6

Fig. 5

7. 8.

Fig. 7 Fig. 8

Screw the M4x8 Captive screw to close the

driver cover.

Tighten the Gland with the help of box

spanner with a torque of 2 to 2.5 Nm.

All the pictures in the MI sheet are representative only and may vary from the Actual Product.

Secure the Gasket on the housing rib. Place the

Driver Cover on the housing matching with the

profile of gasket.

Fix the driver tray as shown in the figure.

Care to be taken that no force to be applied on

earthing wires during the process.

40 mm 8-9 mm

O 8-10 mm

Loosen the Gland with the help of box

spanner and insert the wire from the Pole

mounting side. Take wire length of 80mm

inside the compartment.

Fig. 9

Make the electrical connections in 3 pole connector

as per the LNE marking. Then, connect the LED

Engine wire connections with the driver output.

Fig. 10

Fig.3

11.

This luminaire is suitable for Pole of outer

Dia 48mm to Dia 60mm. Tighten the screws

with a torque of 8Nm.

Tighten the M4 Retainer Screw after properly

placing the Driver Cover with initially a torque of

1Nm, then finally tighten with a torque of 1.2Nm.

10.

For pre-wired luminaire, directly connect it to the

incoming Power Cable. Wires to be properly

terminated to ensure safety, preferably using a IP65

sealed connector (not part of supply).

Ensure ground wire is properly connected.

For non-prewired luminaire follow the instructions

as per the steps defined.

DRIVER

SIDE

OUTER

SIDE

Fig. 11

All the pictures in the MI sheet are representative only and may vary from the Actual Product.

4mm

Andere Philips Laterne Handbücher

Philips

Philips Ledinaire Waterproof WT050C Benutzerhandbuch

Philips

Philips Selecon PLFR1MKII-03 Bedienungsanleitung

Philips

Philips VARI-Lite VL4000 Bedienungsanleitung

Philips

Philips LED Luminaires Bedienungsanleitung

Philips

Philips GentleSpace Gen3 Bedienungsanleitung

Philips

Philips CMFIC Series Bedienungsanleitung

Philips

Philips LifeLight Series Bedienungsanleitung

Philips

Philips CoreLine BN120C Series Bedienungsanleitung

Philips

Philips Iridium gen4 Benutzerhandbuch

Philips

Philips GSA ST321Y Bedienungsanleitung

Philips

Philips series Bedienungsanleitung

Philips

Philips PrimeSet LDM524 Bedienungsanleitung

Philips

Philips ClearScape LED Series Bedienungsanleitung

Philips

Philips SmartBirght BN013C Series Benutzerhandbuch

Philips

Philips InteGrade Bedienungsanleitung

Philips

Philips Luma gen 2 Series Bedienungsanleitung

Philips

Philips eColor Graze Powercore Bedienungsanleitung

Philips

Philips SFRA LUMINAIRE TO RND/SQ POLE Bedienungsanleitung

Philips

Philips Stylid Evo Compact ST770B Bedienungsanleitung

Philips

Philips CZS102 Bedienungsanleitung

Philips

Philips Coreline XL Bedienungsanleitung

Philips

Philips SolarSpot Bedienungsanleitung

Philips

Philips 16942-87-16 Bedienungsanleitung

Philips

Philips CoreLine Waterproof WT120C G2 EL MDU Bedienungsanleitung

Beliebte Laterne Handbücher anderer Marken

KYOWA

KYOWA KW-9114 Bedienungsanleitung

Stahl

Stahl ECOLUX 6610 Series Bedienungsanleitung

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Bedienungsanleitung

PRG

PRG VARI LITE VL5 Bedienungsanleitung

Raytec

Raytec VARIO2 series Bedienungsanleitung

ENSA

ENSA LEDBT18WS2 Bedienungsanleitung

LUG

LUG OFFICE LB LED N/T Bedienungsanleitung

GE Wallighter 250 Bedienungsanleitung

Draper

Draper RLEDL19/B Bedienungsanleitung

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Bedienungsanleitung

Panasonic

Panasonic EY3741B57 Bedienungsanleitung

Clas Ohlson

Clas Ohlson LCC8T Bedienungsanleitung

Coolon

Coolon WDN-140 Bedienungsanleitung

Holiday Travel

Holiday Travel 834873 Bedienungsanleitung

BEGA

BEGA 84 036 Bedienungsanleitung

BEGA

BEGA 33 596 Bedienungsanleitung

Dale Tiffany

Dale Tiffany GT701162 Bedienungsanleitung

Wagan

Wagan Brite Nite Pop-Up USB Lantern Bedienungsanleitung