Philips SL ePAR 180 LED Luminaire Bedienungsanleitung

SL ePAR 180 LED Luminaire

SL ePAR 180 User’s Manual

www.Philips.com/Showline

24-004-3564-00 Rev1.0

SL ePAR 180 LED Luminaire installation & User’s Manual

website

Installation & User’s Manual

SL ePAR 180 LED Luminaire

Additional Resources for DMX512

For more information on installing DMX512 control systems, the following publication is available for purchase

from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide

for Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:

USITT

315 South Crouse Avenue, Suite 200

Syracuse, NY 13210-1844

Phone: 1.800.938.7488 or 1.315.463.6463

www.usitt.org

Showline Limited Two-Year Warranty

Showline offers a two-year limited warranty of its luminaires against defects in materials or workmanship from the

date of delivery. A copy of the Showline two-year limited warranty containing specific terms and conditions can be

obtained by contacting your local Showline office.

You must have access to a mains circuit breaker or other power disconnect device

mains circuit breaker off before installation. Installing the device with power on may expose you to

TABLE OF CONTENTS

Showline Offices Inside Front Cover

IMPORTANT INFORMATION

Warnings and Notices

Additional Resources for DMX512

Showline Limited Two-Year Warranty

TABLE OF CONTENTS

PREFACE

About this Manual

Included Items

Accessories

SL ePAR 180 LED LUMINAIRE OVERVIEW

SL ePAR 180 LED Luminaire Components

Common Luminaire Components

LCD Display / Menu System

INSTALLATION AND SET UP

Power Requirements

Connecting Power

Floor Mounting

Truss/Hanging Applications

SL ePAR 180 LED Luminaire

Connecting to the DMX512 Network

Mounting Luminaire

OPERATION AND PROGRAMMING

LCD Display and Menu System

LCD Display and Menu System Operation

SL ePAR 180 LED Luminaire Menu Tree

Dimming Curve Selection

Master / Slave Operational Mode

DMX CONTROL

RDM PARAMETER IDs

16-Bit Mode

8-Bit Mode

HSIC Mode

DMX Timing Channel Detail

SL ePAR 180 LED Luminaire DMX Mapping

SL ePAR 180 LED Luminaire RDM Parameter IDs

CLEANING AND CARE

Special Cleaning and Care Instructions

Front Lens Cleaning

Service and Maintenance

Accessories

TECHNICAL SPECIFICATIONS

Operational Specifications

Luminaire Dimensions

Table of contents

Installation & User’s Manual SL ePAR 180 LED Luminaire

Installation & User’s Manual

SL ePAR 180 LED Luminaire

PREFACE

1. About this Manual

The document provides installation and operation instructions for the following products:

Please read all instructions before installing or using this product. Retain this manual for future reference.

Additional product information and descriptions may be found on the product specification sheet.

Note: The SL ePAR 180 LED Luminaire is universal voltage 100 to 240 VAC (auto-ranging).

2. Included Items

3. Accessories

Each SL ePAR 180 LED Luminaire includes the following items:

SL ePAR 180 LED Luminaire

SL 0 LED LuminaireePAR 18

Installation and User’s Manual (this document)

About this Manual

PC1BE - AC Power Input Cable (39 inches / 1 metre)

Contact your Authorized Showline Dealer for prices and availability of all accessories for SL ePAR 180

LED Luminaires.

SL ePAR 180 LED Luminaire Overview

Installation & User’s Manual SL ePAR 180 LED Luminaire

SL ePAR 180 LED Luminaire Overview

1. SL ePAR 180 LED Luminaire Components

Common Luminaire Components

Figure 1: SL ePAR 180 LED Luminaire Components

Front of Luminaire Rear of Luminiare

DMX512-A /

LCD Display /

High Intensity LED Array

Yoke Assembly

Luminaire Head Assembly

DMX512-A /

Accessory Holder

Yoke (Tilt) Position

Locking Handle

Truss Hook / Clamp

Attachment Point

Accessory Holder Clip

RDM Input RDM THRU

Menu System AC Power Input

Installation & User’s Manual

SL ePAR 180 LED Luminaire

LCD Display/Menu System

LCD Display / Menu System

Note: For Menu operation and programming details, refer to the "LCD Display and Menu System” on page 9.

Figure 2: LCD Display & Menu System

LEFT Arrow Button RIGHT Arrow Button

ENTER Button

EXIT Button

LCD Display

INSTALLATION AND SET UP

1. Power Requirements

The SL ePAR 180 LED Luminaire operates on AC input voltages from 100 to 240 VAC.

WARNING! This luminaire does not contain an ON/OFF switch. Always disconnect the power input cable to

completely remove power from the luminaire when not in use.

AC Power Operation

When connected to an AC source, the luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The

luminaire contains an auto-ranging power supply. Each luminaire can draw up to 180 Watts.

Table 1: SL ePAR 180Voltage (VAC) vs. Current*

Voltage (AC)Total Current (A)Voltage (AC)Total Current (A)

100 180

110 190

120 200

130 210

140 220

150 230

160

170

1.80

1.63

1.50

1.38

1.29

1.20

1.13

1.06

0.75

0.78

0.82

0.86

0.90

0.95

1.0

240

Installation and Set up

Installation & User’s Manual SL ePAR 180 LED Luminaire

2. Connecting Power

Direct connection to a AC power source using an AC input cable.

A total of 3 wires/conductors need to be brought to the luminaire. The following wiring scheme is required:

Wire Colour Purpose

Table 2: SL ePAR 180 LED Luminaire AC Input Connections

Brown Main / Line(100 to 240VAC)

Neutral

Ground(Earth)

Blue

Green/Yellow

Note: It is recommended that all the wiring works must be conducted by a qualified person.

Warning!

To reduce the risk of electrical shock or fire, do not expose this luminaire to rain or moisture.

Don not stare at the light of this luminaire, the bright light can damage the eyes.

Do not overload circuits!

3. Connecting to the DMX 512 Network

Basic DMX512 installation consists of connecting multiple SL ePAR 180 LED Luminaires together (up to 32 luminaires)

in a "daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to the DMX connector on

the connector on the first luminaire to first SL ePAR 180 LED Luminaire. Another cable runs from the other DMX

a DMX connector device to be controlled).on the next SL ePAR 180 LED Luminaire (or DMX512

Luminaire

Rear of Luminaire

DMX512-A / RDM DMX512-A / RDM

Input Connector THRU Connector

Figure 3: SL ePAR 180 LED Luminaire DMX512 Input / THRU Connections

Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on

page 1. For SL ePAR 180 LED Luminaire DMX Mapping, refer to "DMX CONTROL" on page 14.

Installation & User’s Manual

SL ePAR 180 LED Luminaire

Mounting Luminaire 7

Figure 4: SL ePAR 180 LED Luminaire - DMX512 Connections

DMX512 (out to the next luminaire or

DMX512 controlled device)

DMX512

DMX512 (out from first

to second luminaire)

DMX512 Connections

Note: Remaining pins on each connector are not used.

DMX512 Signal XLR Pin

Common (Drain) 1

DMX512 - 2

DMX512 + 3

(from console or

control device)

4. Mounting Luminaire

Floor Mounting

The SL ePAR 180 LED Luminaire is designed to sit directly on its yoke assembly in a floor installation application. When

used en the locking handle securing the inner portion of the yoke assembly and separate in this type of application, loos

out Figure 5). Be sure to leave enough space around the luminaire to allow proper, uninterrupted airflow(as shown in

for cooling.

Figure 5: Floor Mounting

Yoke Assembly

Inner Portion (Stand)

of Yoke Assembly

Truss / Hanging Applications

The SL ePAR 180 LED Luminaire is provided with the ability to hang via truss hooks, clamps, etc. (sold separately).

Simply attach hook, clamp, etc. to the SL ePAR 180 LED Luminaire assembly in the provided M10 holes.enclosure

It is recommended (and may be required by local and national safety codes) to use and install a safety cable (sold

separately) as illustrated in Figure 6. When hanging the fixture, be sure to leave enough space around the luminaire

to to for allow proper, uninterrupted airflow for cooling and positioning. Refer "Luminaire Dimensions" on page 35

spacing (dimensional) requirements.

OPERATION AND PROGRAMMING

Installation & User’s Manual SL ePAR 180 LED Luminaire

OPERATION AND PROGRAMMING

1. LCD Display and Menu System

SL PAR 150 RGBW LED Luminaires

The SL ePAR 180 LED Luminaire’s LCD Display and Menu System provides local control for accessing the

following settings:

Presets (Standard and User Defined)

Colour Filters

Effects (Chases - preloaded and user defined)

Strobe / Timing

Fixture Settings

Fixture Lockout (to prevent changes)

Password Setting

Current Fixture Operational Status

Setting the DMX512 Address

Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired. For

the SL ePAR 180 LED Luminaire menu structure, see "SL ePAR 180 LED Luminaire Menu Tree" on page 11.

Upon power up, the LCD will display the main screen display menu of SL ePAR 180 LED Luminaire.

Press “ ” or “ ” to select the press “OK” to enter the desired function menu.

Figure 6: Mounting the Fixture - Hanging Applications

SAFETY CABLE: Is sold separately and

recommended for all hanging installation and

may be required by national and local codes.

Use enclosure handles for safety cable anchor

point for this fixture.

Truss Hook or Clamp

(sold separately)

Inhaltsverzeichnis

Andere Philips Beleuchtungsausrüstung Handbücher

Philips

Philips CoreLine WT120C LED18S/840 PSU L600 Bedienungsanleitung

Philips

Philips StoreSet Linear SM504TI Bedienungsanleitung

Philips

Philips 56424-31-16 Bedienungsanleitung

Philips

Philips FBH 020 Bedienungsanleitung

Philips

Philips Bodine B54 Bedienungsanleitung

Philips

Philips Selecon Bedienungsanleitung

Philips

Philips 31608-48-16 Bedienungsanleitung

Philips

Philips 57946-17-16 Bedienungsanleitung

Philips

Philips PLFRESNEL 1 LED LUMINAIRES Bedienungsanleitung

Philips

Philips hue Bedienungsanleitung

Philips

Philips Illuminate Bedienungsanleitung

Philips

Philips EasySmart InstantFit t8 Bedienungsanleitung

Philips

Philips 59510-17-16 Bedienungsanleitung

Philips

Philips goLITE BLU Bedienungsanleitung

Philips

Philips BN012C Benutzerhandbuch

Philips

Philips Selecon Bedienungsanleitung

Philips

Philips Selecon Accent LED Beamshaper Bedienungsanleitung

Philips

Philips SL BAR 660 Bedienungsanleitung

Philips

Philips Hue Runner Bedienungsanleitung

Philips

Philips CR434B Bedienungsanleitung

Philips

Philips Bodine B426 Bedienungsanleitung

Philips

Philips ColorDial Pro Bedienungsanleitung

Philips

Philips VL440 Spot Bedienungsanleitung

Philips

Philips ColorBlast TRX Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung